Hello.
Jordan Crouse wrote:
Maybe Jordan could try again with a fresh patch because it really does
seem to help...
Here you go, fresh out of the oven.. :)
------------------------------------------------------------------------
ALCHEMY: AU1200 I2C modifications
From: Jordan Crouse <jordan.crouse@xxxxxxx>
Modifications to the existing AU1XXX I2C controller for the Au1200.
Signed-off-by: Jordan Crouse <jordan.crouse@xxxxxxx>
---
arch/mips/au1000/db1x00/board_setup.c | 37 +++++++++++++++++++++++++++++
drivers/i2c/busses/Kconfig | 2 +-
drivers/i2c/busses/i2c-au1550.c | 29 ++++++++++++++++++-----
include/asm-mips/mach-au1x00/au1xxx_psc.h | 7 +++++
4 files changed, 67 insertions(+), 8 deletions(-)
diff --git a/arch/mips/au1000/db1x00/board_setup.c b/arch/mips/au1000/db1x00/board_setup.c
index f00ec3b..a2638c8 100644
--- a/arch/mips/au1000/db1x00/board_setup.c
+++ b/arch/mips/au1000/db1x00/board_setup.c
@@ -76,6 +76,43 @@ #if defined(CONFIG_IRDA) && (defined(CON
#endif
bcsr->pcmcia = 0x0000; /* turn off PCMCIA power */
+#if defined(CONFIG_I2C_AU1550) && defined(CONFIG_MIPS_DB1200)
+ {
+ u32 freq0, clksrc;
+
+ /* Select SMBUS in CPLD */
+ bcsr->resets &= ~(BCSR_RESETS_PCS0MUX);
+
+ pin_func = au_readl(SYS_PINFUNC);
+ au_sync();
+ pin_func &= ~(3<<17 | 1<<4);
+ /* Set GPIOs correctly */
+ pin_func |= 2<<17;
+ au_writel(pin_func, SYS_PINFUNC);
+ au_sync();
+
+ /* The i2c driver depends on 50Mhz clock */
+ freq0 = au_readl(SYS_FREQCTRL0);
+ au_sync();
+ freq0 &= ~(SYS_FC_FRDIV1_MASK | SYS_FC_FS1 | SYS_FC_FE1);
+ freq0 |= (3<<SYS_FC_FRDIV1_BIT);
+ /* 396Mhz / (3+1)*2 == 49.5Mhz */
+ au_writel(freq0, SYS_FREQCTRL0);
+ au_sync();
+ freq0 |= SYS_FC_FE1;
+ au_writel(freq0, SYS_FREQCTRL0);
+ au_sync();
+
+ clksrc = au_readl(SYS_CLKSRC);
+ au_sync();
+ clksrc &= ~0x01f00000;
+ /* bit 22 is EXTCLK0 for PSC0 */
+ clksrc |= (0x3 << 22);
+ au_writel(clksrc, SYS_CLKSRC);
+ au_sync();
+ }
+#endif
+
#ifdef CONFIG_MIPS_MIRAGE
/* enable GPIO[31:0] inputs */
au_writel(0, SYS_PININPUTEN);
Alas, I have to NAK this. DBAu1200 code should be in
arch/mips/au1000/pb1200/...
diff --git a/include/asm-mips/mach-au1x00/au1xxx_psc.h b/include/asm-mips/mach-au1x00/au1xxx_psc.h
index faa5ffe..a523079 100644
--- a/include/asm-mips/mach-au1x00/au1xxx_psc.h
+++ b/include/asm-mips/mach-au1x00/au1xxx_psc.h
@@ -48,6 +48,11 @@ #define PSC0_BASE_ADDR 0xb1a00000
#define PSC1_BASE_ADDR 0xb1b00000
#endif
+#ifdef CONFIG_SOC_AU1200
+#define PSC0_BASE_ADDR 0xb1a00000
+#define PSC1_BASE_ADDR 0xb1b00000
+#endif
+
/* The PSC select and control registers are common to
* all protocols.
*/
Well, I have already submitted this change this March, here's the patch:
http://www.linux-mips.org/archives/linux-mips/2006-03/msg00245.html
. As usual, Ralf is not eager to commit my patches... :-/
Thou wait... that hunk won't even aplly to the current git tree... Looks
like this patch is trying to redeclare PSC base addresses for Au1200 on top of
my patch... If it's so, NAK.
WBR, Sergei
