Hello all,
The patch below adds base support for NEC EMMA2RH Mark-eins board.
Any comments and feedback will be appreciated
Signed-off-by: dmitry pervushin <dpervushin@xxxxxxxxxxxxx>
Index: linux-2.6.10/arch/mips/configs/emma2rh_defconfig
===================================================================
--- /dev/null
+++ linux-2.6.10/arch/mips/configs/emma2rh_defconfig
@@ -0,0 +1,1088 @@
+#
+# Automatically generated make config: don't edit
+# Linux kernel version: 2.6.10_mvl401
+# Thu Apr 27 19:51:02 2006
+#
+CONFIG_MIPS=y
+# CONFIG_MIPS64 is not set
+# CONFIG_64BIT is not set
+CONFIG_MIPS32=y
+
+#
+# Code maturity level options
+#
+CONFIG_EXPERIMENTAL=y
+# CONFIG_CLEAN_COMPILE is not set
+CONFIG_BROKEN=y
+CONFIG_BROKEN_ON_SMP=y
+CONFIG_LOCK_KERNEL=y
+
+#
+# General setup
+#
+CONFIG_LOCALVERSION=""
+CONFIG_SWAP=y
+CONFIG_SYSVIPC=y
+CONFIG_SYSVIPC_SEMMNI=128
+CONFIG_SYSVIPC_SEMMSL=250
+CONFIG_POSIX_MQUEUE=y
+CONFIG_BSD_PROCESS_ACCT=y
+# CONFIG_BSD_PROCESS_ACCT_V3 is not set
+CONFIG_SYSCTL=y
+# CONFIG_AUDIT is not set
+CONFIG_LOG_BUF_SHIFT=14
+CONFIG_HOTPLUG=y
+CONFIG_KOBJECT_UEVENT=y
+CONFIG_IKCONFIG=y
+CONFIG_IKCONFIG_PROC=y
+CONFIG_EMBEDDED=y
+CONFIG_KALLSYMS=y
+# CONFIG_KALLSYMS_ALL is not set
+# CONFIG_KALLSYMS_EXTRA_PASS is not set
+CONFIG_FUTEX=y
+CONFIG_EPOLL=y
+# CONFIG_CC_OPTIMIZE_FOR_SIZE is not set
+CONFIG_SHMEM=y
+CONFIG_CC_ALIGN_FUNCTIONS=0
+CONFIG_CC_ALIGN_LABELS=0
+CONFIG_CC_ALIGN_LOOPS=0
+CONFIG_CC_ALIGN_JUMPS=0
+CONFIG_LTT_MAX_HANDLES=128
+# CONFIG_BOOT_FLIGHT_RECORDER is not set
+CONFIG_LOCKLESS=y
+CONFIG_BOOT_FLIGHT_BUFFERS=4
+CONFIG_BOOT_FLIGHT_SIZE=524288
+CONFIG_FLIGHT_PROC_BUFFERS=8
+CONFIG_FLIGHT_PROC_SIZE=8192
+CONFIG_NEWEV=y
+CONFIG_CSTM=y
+# CONFIG_TINY_SHMEM is not set
+
+#
+# Loadable module support
+#
+CONFIG_MODULES=y
+CONFIG_MODULE_UNLOAD=y
+CONFIG_MODULE_FORCE_UNLOAD=y
+CONFIG_OBSOLETE_MODPARM=y
+CONFIG_MODVERSIONS=y
+# CONFIG_MODULE_SRCVERSION_ALL is not set
+CONFIG_KMOD=y
+
+#
+# Machine selection
+#
+# CONFIG_MACH_JAZZ is not set
+# CONFIG_MACH_VR41XX is not set
+# CONFIG_MIPS_BRCM is not set
+# CONFIG_TOSHIBA_JMR3927 is not set
+# CONFIG_MIPS_COBALT is not set
+# CONFIG_MACH_DECSTATION is not set
+# CONFIG_MIPS_EV64120 is not set
+# CONFIG_MIPS_EV96100 is not set
+# CONFIG_MIPS_IVR is not set
+# CONFIG_LASAT is not set
+# CONFIG_MIPS_ITE8172 is not set
+# CONFIG_MIPS_ATLAS is not set
+# CONFIG_MIPS_MALTA is not set
+# CONFIG_MIPS_SEAD is not set
+# CONFIG_MOMENCO_OCELOT is not set
+# CONFIG_MOMENCO_OCELOT_G is not set
+# CONFIG_MOMENCO_OCELOT_C is not set
+# CONFIG_MOMENCO_OCELOT_3 is not set
+# CONFIG_PNX8550_V2PCI is not set
+# CONFIG_PNX8550_JBS is not set
+# CONFIG_PNX8550_STB810 is not set
+# CONFIG_MOMENCO_JAGUAR_ATX is not set
+# CONFIG_PMC_YOSEMITE is not set
+# CONFIG_DDB5074 is not set
+# CONFIG_DDB5476 is not set
+# CONFIG_DDB5477 is not set
+# CONFIG_VR5701_SG2 is not set
+# CONFIG_NEC_OSPREY is not set
+CONFIG_MARKEINS=y
+# CONFIG_SGI_IP22 is not set
+# CONFIG_SOC_AU1X00 is not set
+# CONFIG_SIBYTE_SB1xxx_SOC is not set
+# CONFIG_SNI_RM200_PCI is not set
+# CONFIG_TOSHIBA_RBTX4927 is not set
+# CONFIG_TOSHIBA_RBTX4938 is not set
+# CONFIG_TOSHIBA_RBTX4939 is not set
+# CONFIG_CAVIUM_OCTEON_EBT3000 is not set
+# CONFIG_PREEMPT_NONE is not set
+# CONFIG_PREEMPT_VOLUNTARY is not set
+# CONFIG_PREEMPT_DESKTOP is not set
+CONFIG_PREEMPT_RT=y
+CONFIG_PREEMPT=y
+CONFIG_PREEMPT_SOFTIRQS=y
+CONFIG_PREEMPT_HARDIRQS=y
+CONFIG_PREEMPT_RCU=y
+CONFIG_PREEMPT_BKL=y
+CONFIG_RWSEM_GENERIC_SPINLOCK=y
+CONFIG_ASM_SEMAPHORES=y
+CONFIG_HAVE_DEC_LOCK=y
+CONFIG_DMA_NONCOHERENT=y
+# CONFIG_CPU_LITTLE_ENDIAN is not set
+CONFIG_IRQ_CPU=y
+CONFIG_SWAP_IO_SPACE=y
+CONFIG_EMMA2RH=y
+CONFIG_MIPS_L1_CACHE_SHIFT=5
+
+#
+# CPU selection
+#
+CONFIG_CPU_MIPS32=y
+# CONFIG_CPU_MIPS64 is not set
+# CONFIG_CPU_R3000 is not set
+# CONFIG_CPU_TX39XX is not set
+# CONFIG_CPU_VR41XX is not set
+# CONFIG_CPU_R4300 is not set
+# CONFIG_CPU_R4X00 is not set
+# CONFIG_CPU_TX49XX is not set
+# CONFIG_CPU_R5000 is not set
+# CONFIG_CPU_R5432 is not set
+# CONFIG_CPU_R5500 is not set
+# CONFIG_CPU_R6000 is not set
+# CONFIG_CPU_NEVADA is not set
+# CONFIG_CPU_R8000 is not set
+# CONFIG_CPU_R10000 is not set
+# CONFIG_CPU_RM7000 is not set
+# CONFIG_CPU_RM9000 is not set
+# CONFIG_CPU_SB1 is not set
+# CONFIG_CPU_CAVIUM_OCTEON is not set
+CONFIG_PAGE_SIZE_4KB=y
+# CONFIG_PAGE_SIZE_8KB is not set
+# CONFIG_PAGE_SIZE_16KB is not set
+# CONFIG_PAGE_SIZE_64KB is not set
+# CONFIG_VTAG_ICACHE is not set
+# CONFIG_64BIT_PHYS_ADDR is not set
+# CONFIG_CPU_ADVANCED is not set
+CONFIG_CPU_HAS_LLSC=y
+CONFIG_CPU_HAS_SYNC=y
+# CONFIG_HIGH_RES_TIMERS is not set
+# CONFIG_CPU_TIMER is not set
+
+#
+# Bus options (PCI, PCMCIA, EISA, ISA, TC)
+#
+CONFIG_HW_HAS_PCI=y
+CONFIG_PCI=y
+# CONFIG_PCI_LEGACY_PROC is not set
+CONFIG_PCI_NAMES=y
+CONFIG_MMU=y
+
+#
+# PCCARD (PCMCIA/CardBus) support
+#
+# CONFIG_PCCARD is not set
+
+#
+# PC-card bridges
+#
+
+#
+# PCI Hotplug Support
+#
+# CONFIG_HOTPLUG_PCI is not set
+
+#
+# Executable file formats
+#
+CONFIG_BINFMT_ELF=y
+# CONFIG_BINFMT_MISC is not set
+CONFIG_TRAD_SIGNALS=y
+# CONFIG_BINFMT_IRIX is not set
+
+#
+# Device Drivers
+#
+
+#
+# Generic Driver Options
+#
+CONFIG_STANDALONE=y
+CONFIG_PREVENT_FIRMWARE_BUILD=y
+# CONFIG_FW_LOADER is not set
+# CONFIG_DEBUG_DRIVER is not set
+
+#
+# Memory Technology Devices (MTD)
+#
+CONFIG_MTD=y
+# CONFIG_MTD_DEBUG is not set
+# CONFIG_MTD_CONCAT is not set
+CONFIG_MTD_PARTITIONS=y
+# CONFIG_MTD_REDBOOT_PARTS is not set
+CONFIG_MTD_CMDLINE_PARTS=y
+
+#
+# User Modules And Translation Layers
+#
+CONFIG_MTD_CHAR=y
+CONFIG_MTD_BLOCK=y
+# CONFIG_FTL is not set
+# CONFIG_NFTL is not set
+# CONFIG_INFTL is not set
+# CONFIG_RFD_FTL is not set
+
+#
+# RAM/ROM/Flash chip drivers
+#
+CONFIG_MTD_CFI=y
+# CONFIG_MTD_JEDECPROBE is not set
+CONFIG_MTD_GEN_PROBE=y
+# CONFIG_MTD_CFI_ADV_OPTIONS is not set
+CONFIG_MTD_MAP_BANK_WIDTH_1=y
+CONFIG_MTD_MAP_BANK_WIDTH_2=y
+CONFIG_MTD_MAP_BANK_WIDTH_4=y
+# CONFIG_MTD_MAP_BANK_WIDTH_8 is not set
+# CONFIG_MTD_MAP_BANK_WIDTH_16 is not set
+# CONFIG_MTD_MAP_BANK_WIDTH_32 is not set
+CONFIG_MTD_CFI_I1=y
+CONFIG_MTD_CFI_I2=y
+# CONFIG_MTD_CFI_I4 is not set
+# CONFIG_MTD_CFI_I8 is not set
+# CONFIG_MTD_CFI_INTELEXT is not set
+CONFIG_MTD_CFI_AMDSTD=y
+CONFIG_MTD_CFI_AMDSTD_RETRY=0
+# CONFIG_MTD_CFI_STAA is not set
+CONFIG_MTD_CFI_UTIL=y
+# CONFIG_MTD_RAM is not set
+# CONFIG_MTD_ROM is not set
+# CONFIG_MTD_ABSENT is not set
+# CONFIG_MTD_OBSOLETE_CHIPS is not set
+# CONFIG_MTD_XIP is not set
+
+#
+# Mapping drivers for chip access
+#
+# CONFIG_MTD_COMPLEX_MAPPINGS is not set
+# CONFIG_MTD_PHYSMAP is not set
+# CONFIG_MTD_MULTI_PHYSMAP is not set
+CONFIG_MTD_EMMA2RH=y
+# CONFIG_MTD_PLATRAM is not set
+
+#
+# Self-contained MTD device drivers
+#
+# CONFIG_MTD_PMC551 is not set
+# CONFIG_MTD_SLRAM is not set
+# CONFIG_MTD_PHRAM is not set
+# CONFIG_MTD_MTDRAM is not set
+# CONFIG_RAMTD is not set
+# CONFIG_MTD_BLKMTD is not set
+# CONFIG_MTD_BLOCK2MTD is not set
+
+#
+# Disk-On-Chip Device Drivers
+#
+# CONFIG_MTD_DOC2000 is not set
+# CONFIG_MTD_DOC2001 is not set
+# CONFIG_MTD_DOC2001PLUS is not set
+
+#
+# NAND Flash Device Drivers
+#
+# CONFIG_MTD_NAND is not set
+
+#
+# Parallel port support
+#
+# CONFIG_PARPORT is not set
+
+#
+# Plug and Play support
+#
+
+#
+# Block devices
+#
+# CONFIG_BLK_DEV_FD is not set
+# CONFIG_BLK_CPQ_DA is not set
+# CONFIG_BLK_CPQ_CISS_DA is not set
+# CONFIG_BLK_DEV_DAC960 is not set
+# CONFIG_BLK_DEV_UMEM is not set
+CONFIG_BLK_DEV_LOOP=m
+CONFIG_BLK_DEV_CRYPTOLOOP=m
+# CONFIG_BLK_DEV_NBD is not set
+# CONFIG_BLK_DEV_SX8 is not set
+# CONFIG_BLK_DEV_RAM is not set
+CONFIG_BLK_DEV_RAM_COUNT=16
+CONFIG_INITRAMFS_SOURCE=""
+CONFIG_LBD=y
+# CONFIG_CDROM_PKTCDVD is not set
+
+#
+# IO Schedulers
+#
+CONFIG_IOSCHED_NOOP=y
+CONFIG_IOSCHED_AS=y
+CONFIG_IOSCHED_DEADLINE=y
+CONFIG_IOSCHED_CFQ=y
+
+#
+# ATA/ATAPI/MFM/RLL support
+#
+# CONFIG_IDE is not set
+
+#
+# SCSI device support
+#
+CONFIG_SCSI=m
+# CONFIG_SCSI_PROC_FS is not set
+
+#
+# SCSI support type (disk, tape, CD-ROM)
+#
+CONFIG_BLK_DEV_SD=m
+# CONFIG_CHR_DEV_ST is not set
+# CONFIG_CHR_DEV_OSST is not set
+# CONFIG_BLK_DEV_SR is not set
+CONFIG_CHR_DEV_SG=m
+
+#
+# Some SCSI devices (e.g. CD jukebox) support multiple LUNs
+#
+# CONFIG_SCSI_MULTI_LUN is not set
+# CONFIG_SCSI_CONSTANTS is not set
+# CONFIG_SCSI_LOGGING is not set
+
+#
+# SCSI Transport Attributes
+#
+# CONFIG_SCSI_SPI_ATTRS is not set
+# CONFIG_SCSI_FC_ATTRS is not set
+
+#
+# SCSI low-level drivers
+#
+# CONFIG_BLK_DEV_3W_XXXX_RAID is not set
+# CONFIG_SCSI_3W_9XXX is not set
+# CONFIG_SCSI_ACARD is not set
+# CONFIG_SCSI_AACRAID is not set
+# CONFIG_SCSI_AIC7XXX is not set
+# CONFIG_SCSI_AIC7XXX_OLD is not set
+# CONFIG_SCSI_AIC79XX is not set
+# CONFIG_SCSI_ADP94XX is not set
+# CONFIG_SCSI_DPT_I2O is not set
+# CONFIG_SCSI_ADVANSYS is not set
+# CONFIG_MEGARAID_NEWGEN is not set
+# CONFIG_MEGARAID_LEGACY is not set
+# CONFIG_SCSI_SATA is not set
+# CONFIG_SCSI_BUSLOGIC is not set
+# CONFIG_SCSI_CPQFCTS is not set
+# CONFIG_SCSI_DMX3191D is not set
+# CONFIG_SCSI_EATA is not set
+# CONFIG_SCSI_EATA_PIO is not set
+# CONFIG_SCSI_FUTURE_DOMAIN is not set
+# CONFIG_SCSI_GDTH is not set
+# CONFIG_SCSI_IPS is not set
+# CONFIG_SCSI_INITIO is not set
+# CONFIG_SCSI_INIA100 is not set
+# CONFIG_SCSI_SYM53C8XX_2 is not set
+# CONFIG_SCSI_IPR is not set
+# CONFIG_SCSI_PCI2000 is not set
+# CONFIG_SCSI_PCI2220I is not set
+# CONFIG_SCSI_QLOGIC_ISP is not set
+# CONFIG_SCSI_QLOGIC_FC is not set
+# CONFIG_SCSI_QLOGIC_1280 is not set
+CONFIG_SCSI_QLA2XXX=m
+# CONFIG_SCSI_QLA21XX is not set
+# CONFIG_SCSI_QLA22XX is not set
+# CONFIG_SCSI_QLA2300 is not set
+# CONFIG_SCSI_QLA2322 is not set
+# CONFIG_SCSI_QLA6312 is not set
+# CONFIG_SCSI_QLA6322 is not set
+# CONFIG_SCSI_DC395x is not set
+# CONFIG_SCSI_DC390T is not set
+# CONFIG_SCSI_NSP32 is not set
+# CONFIG_SCSI_DEBUG is not set
+
+#
+# Multi-device support (RAID and LVM)
+#
+# CONFIG_MD is not set
+
+#
+# Fusion MPT device support
+#
+# CONFIG_FUSION is not set
+
+#
+# IEEE 1394 (FireWire) support
+#
+# CONFIG_IEEE1394 is not set
+
+#
+# I2O device support
+#
+# CONFIG_I2O is not set
+
+#
+# Networking support
+#
+CONFIG_NET=y
+
+#
+# Networking options
+#
+CONFIG_PACKET=y
+CONFIG_PACKET_MMAP=y
+# CONFIG_NETLINK_DEV is not set
+CONFIG_UNIX=y
+CONFIG_NET_KEY=y
+# CONFIG_NET_KEY_MIGRATE is not set
+CONFIG_USE_POLICY_FWD=y
+CONFIG_INET=y
+CONFIG_IP_MULTICAST=y
+CONFIG_IP_ADVANCED_ROUTER=y
+CONFIG_IP_MULTIPLE_TABLES=y
+CONFIG_IP_ROUTE_MULTIPATH=y
+CONFIG_IP_ROUTE_VERBOSE=y
+CONFIG_IP_PNP=y
+# CONFIG_IP_PNP_DHCP is not set
+CONFIG_IP_PNP_BOOTP=y
+# CONFIG_IP_PNP_RARP is not set
+# CONFIG_NET_IPIP is not set
+# CONFIG_NET_IPGRE is not set
+# CONFIG_IP_MROUTE is not set
+# CONFIG_ARPD is not set
+CONFIG_SYN_COOKIES=y
+# CONFIG_INET_AH is not set
+# CONFIG_INET_ESP is not set
+# CONFIG_INET_IPCOMP is not set
+# CONFIG_INET_TUNNEL is not set
+# CONFIG_IP_TCPDIAG is not set
+# CONFIG_IP_TCPDIAG_IPV6 is not set
+CONFIG_IPV6=m
+# CONFIG_IPV6_PRIVACY is not set
+# CONFIG_IPV6_ROUTER_PREF is not set
+# CONFIG_INET6_AH is not set
+# CONFIG_INET6_ESP is not set
+# CONFIG_INET6_IPCOMP is not set
+# CONFIG_INET6_TUNNEL is not set
+# CONFIG_IPV6_TUNNEL is not set
+# CONFIG_IPV6_ADVANCED_ROUTER is not set
+# CONFIG_IPV6_MIP6 is not set
+# CONFIG_NETFILTER is not set
+CONFIG_XFRM=y
+# CONFIG_XFRM_USER is not set
+# CONFIG_XFRM_ENHANCEMENT is not set
+
+#
+# SCTP Configuration (EXPERIMENTAL)
+#
+CONFIG_IP_SCTP=m
+# CONFIG_SCTP_DBG_MSG is not set
+# CONFIG_SCTP_DBG_OBJCNT is not set
+# CONFIG_SCTP_HMAC_NONE is not set
+# CONFIG_SCTP_HMAC_SHA1 is not set
+CONFIG_SCTP_HMAC_MD5=y
+# CONFIG_ATM is not set
+# CONFIG_BRIDGE is not set
+# CONFIG_VLAN_8021Q is not set
+# CONFIG_DECNET is not set
+# CONFIG_LLC2 is not set
+# CONFIG_IPX is not set
+# CONFIG_ATALK is not set
+# CONFIG_X25 is not set
+# CONFIG_LAPB is not set
+# CONFIG_NET_DIVERT is not set
+# CONFIG_ECONET is not set
+# CONFIG_WAN_ROUTER is not set
+
+#
+# QoS and/or fair queueing
+#
+# CONFIG_NET_SCHED is not set
+# CONFIG_NET_CLS_ROUTE is not set
+
+#
+# Network testing
+#
+# CONFIG_NET_PKTGEN is not set
+# CONFIG_NETPOLL is not set
+# CONFIG_NET_POLL_CONTROLLER is not set
+# CONFIG_HAMRADIO is not set
+# CONFIG_IRDA is not set
+# CONFIG_BT is not set
+# CONFIG_IEEE80211 is not set
+CONFIG_NETDEVICES=y
+# CONFIG_DUMMY is not set
+# CONFIG_BONDING is not set
+# CONFIG_EQUALIZER is not set
+# CONFIG_TUN is not set
+
+#
+# ARCnet devices
+#
+# CONFIG_ARCNET is not set
+
+#
+# PHY device support
+#
+# CONFIG_PHYLIB is not set
+
+#
+# Ethernet (10 or 100Mbit)
+#
+CONFIG_NET_ETHERNET=y
+CONFIG_MII=y
+# CONFIG_HAPPYMEAL is not set
+# CONFIG_SUNGEM is not set
+# CONFIG_NET_VENDOR_3COM is not set
+# CONFIG_SMC91X is not set
+
+#
+# Tulip family network device support
+#
+# CONFIG_NET_TULIP is not set
+# CONFIG_HP100 is not set
+
+#
+# Broadcom network devices
+#
+# CONFIG_HND is not set
+CONFIG_NET_PCI=y
+# CONFIG_PCNET32 is not set
+# CONFIG_AMD8111_ETH is not set
+# CONFIG_ADAPTEC_STARFIRE is not set
+# CONFIG_B44 is not set
+# CONFIG_FORCEDETH is not set
+# CONFIG_DGRS is not set
+# CONFIG_EEPRO100 is not set
+# CONFIG_E100 is not set
+# CONFIG_FEALNX is not set
+CONFIG_NATSEMI=y
+# CONFIG_NE2K_PCI is not set
+# CONFIG_8139CP is not set
+# CONFIG_8139TOO is not set
+# CONFIG_SIS900 is not set
+# CONFIG_EPIC100 is not set
+# CONFIG_SUNDANCE is not set
+# CONFIG_TLAN is not set
+# CONFIG_VIA_RHINE is not set
+# CONFIG_LAN_SAA9730 is not set
+
+#
+# Ethernet (1000 Mbit)
+#
+# CONFIG_ACENIC is not set
+# CONFIG_DL2K is not set
+# CONFIG_E1000 is not set
+# CONFIG_NS83820 is not set
+# CONFIG_HAMACHI is not set
+# CONFIG_YELLOWFIN is not set
+# CONFIG_R8169 is not set
+# CONFIG_SK98LIN is not set
+# CONFIG_VIA_VELOCITY is not set
+# CONFIG_TIGON3 is not set
+
+#
+# Ethernet (10000 Mbit)
+#
+# CONFIG_IXGB is not set
+# CONFIG_S2IO is not set
+
+#
+# Token Ring devices
+#
+# CONFIG_TR is not set
+
+#
+# Wireless LAN (non-hamradio)
+#
+# CONFIG_NET_RADIO is not set
+
+#
+# Wan interfaces
+#
+# CONFIG_WAN is not set
+# CONFIG_FDDI is not set
+# CONFIG_HIPPI is not set
+# CONFIG_PPP is not set
+# CONFIG_SLIP is not set
+# CONFIG_NET_FC is not set
+# CONFIG_SHAPER is not set
+# CONFIG_NETCONSOLE is not set
+
+#
+# ISDN subsystem
+#
+# CONFIG_ISDN is not set
+
+#
+# Telephony Support
+#
+# CONFIG_PHONE is not set
+
+#
+# Input device support
+#
+CONFIG_INPUT=y
+
+#
+# Userland interfaces
+#
+# CONFIG_INPUT_MOUSEDEV is not set
+# CONFIG_INPUT_JOYDEV is not set
+# CONFIG_INPUT_TSDEV is not set
+# CONFIG_INPUT_TSLIBDEV is not set
+# CONFIG_INPUT_EVDEV is not set
+# CONFIG_INPUT_EVBUG is not set
+
+#
+# Input I/O drivers
+#
+# CONFIG_GAMEPORT is not set
+CONFIG_SOUND_GAMEPORT=y
+# CONFIG_SERIO is not set
+# CONFIG_SERIO_I8042 is not set
+
+#
+# Input Device Drivers
+#
+# CONFIG_INPUT_KEYBOARD is not set
+# CONFIG_INPUT_MOUSE is not set
+# CONFIG_INPUT_JOYSTICK is not set
+# CONFIG_INPUT_TOUCHSCREEN is not set
+# CONFIG_INPUT_MISC is not set
+
+#
+# Character devices
+#
+# CONFIG_VT is not set
+# CONFIG_SERIAL_NONSTANDARD is not set
+
+#
+# Serial drivers
+#
+CONFIG_SERIAL_8250=y
+CONFIG_SERIAL_8250_CONSOLE=y
+CONFIG_SERIAL_8250_NR_UARTS=4
+# CONFIG_SERIAL_8250_EXTENDED is not set
+
+#
+# Non-8250 serial port support
+#
+CONFIG_SERIAL_CORE=y
+CONFIG_SERIAL_CORE_CONSOLE=y
+CONFIG_UNIX98_PTYS=y
+CONFIG_LEGACY_PTYS=y
+CONFIG_LEGACY_PTY_COUNT=256
+
+#
+# IPMI
+#
+# CONFIG_IPMI_HANDLER is not set
+
+#
+# Watchdog Cards
+#
+# CONFIG_WATCHDOG is not set
+CONFIG_RTC=m
+# CONFIG_RTC_HISTOGRAM is not set
+# CONFIG_BLOCKER is not set
+CONFIG_GEN_RTC=m
+CONFIG_GEN_RTC_X=y
+# CONFIG_DTLK is not set
+# CONFIG_R3964 is not set
+# CONFIG_APPLICOM is not set
+
+#
+# Ftape, the floppy tape device driver
+#
+# CONFIG_DRM is not set
+# CONFIG_RAW_DRIVER is not set
+
+#
+# I2C support
+#
+CONFIG_I2C=y
+CONFIG_I2C_CHARDEV=y
+
+#
+# I2C Algorithms
+#
+# CONFIG_I2C_ALGOBIT is not set
+# CONFIG_I2C_ALGOPCF is not set
+# CONFIG_I2C_ALGOPCA is not set
+# CONFIG_I2C_ALGO_SGI is not set
+CONFIG_I2C_ALGO_EMMA2RH=y
+
+#
+# I2C Hardware Bus support
+#
+# CONFIG_I2C_ALI1535 is not set
+# CONFIG_I2C_ALI1563 is not set
+# CONFIG_I2C_ALI15X3 is not set
+# CONFIG_I2C_AMD756 is not set
+# CONFIG_I2C_AMD8111 is not set
+# CONFIG_I2C_I801 is not set
+# CONFIG_I2C_I810 is not set
+# CONFIG_I2C_ISA is not set
+# CONFIG_I2C_NFORCE2 is not set
+# CONFIG_I2C_PARPORT_LIGHT is not set
+# CONFIG_I2C_PIIX4 is not set
+# CONFIG_I2C_PROSAVAGE is not set
+# CONFIG_I2C_SAVAGE4 is not set
+# CONFIG_SCx200_ACB is not set
+# CONFIG_I2C_SIS5595 is not set
+# CONFIG_I2C_SIS630 is not set
+# CONFIG_I2C_SIS96X is not set
+# CONFIG_I2C_STUB is not set
+# CONFIG_I2C_VIA is not set
+# CONFIG_I2C_VIAPRO is not set
+# CONFIG_I2C_VOODOO3 is not set
+# CONFIG_I2C_PCA_ISA is not set
+# CONFIG_I2C_OMAP is not set
+CONFIG_I2C_EMMA2RH=y
+
+#
+# Hardware Sensors Chip support
+#
+# CONFIG_I2C_SENSOR is not set
+# CONFIG_SENSORS_ADM1021 is not set
+# CONFIG_SENSORS_ADM1025 is not set
+# CONFIG_SENSORS_ADM1026 is not set
+# CONFIG_SENSORS_ADM1031 is not set
+# CONFIG_SENSORS_ASB100 is not set
+# CONFIG_SENSORS_DS1621 is not set
+# CONFIG_SENSORS_FSCHER is not set
+# CONFIG_SENSORS_GL518SM is not set
+# CONFIG_SENSORS_IT87 is not set
+# CONFIG_SENSORS_LM63 is not set
+# CONFIG_SENSORS_LM75 is not set
+# CONFIG_SENSORS_LM77 is not set
+# CONFIG_SENSORS_LM78 is not set
+# CONFIG_SENSORS_LM80 is not set
+# CONFIG_SENSORS_LM83 is not set
+# CONFIG_SENSORS_LM85 is not set
+# CONFIG_SENSORS_LM87 is not set
+# CONFIG_SENSORS_LM90 is not set
+# CONFIG_SENSORS_MAX1619 is not set
+# CONFIG_SENSORS_PC87360 is not set
+# CONFIG_SENSORS_SMSC47M1 is not set
+# CONFIG_SENSORS_VIA686A is not set
+# CONFIG_SENSORS_W83781D is not set
+# CONFIG_SENSORS_W83L785TS is not set
+# CONFIG_SENSORS_W83627HF is not set
+
+#
+# Other I2C Chip support
+#
+# CONFIG_SENSORS_DS1374 is not set
+# CONFIG_SENSORS_EEPROM is not set
+# CONFIG_SENSORS_PCF8574 is not set
+# CONFIG_SENSORS_PCF8591 is not set
+# CONFIG_SENSORS_RTC8564 is not set
+# CONFIG_TPS65010 is not set
+# CONFIG_I2C_DEBUG_CHIP is not set
+
+#
+# SPI support
+#
+# CONFIG_SPI is not set
+# CONFIG_SPI_MASTER is not set
+
+#
+# Dallas's 1-wire bus
+#
+# CONFIG_W1 is not set
+
+#
+# Misc devices
+#
+
+#
+# Multimedia Capabilities Port drivers
+#
+
+#
+# Multimedia devices
+#
+# CONFIG_VIDEO_DEV is not set
+
+#
+# Digital Video Broadcasting Devices
+#
+# CONFIG_DVB is not set
+
+#
+# Graphics support
+#
+# CONFIG_FB is not set
+
+#
+# Sound
+#
+# CONFIG_SOUND is not set
+
+#
+# USB support
+#
+# CONFIG_USB is not set
+CONFIG_USB_ARCH_HAS_HCD=y
+CONFIG_USB_ARCH_HAS_OHCI=y
+
+#
+# NOTE: USB_STORAGE enables SCSI, and 'SCSI disk support' may also be needed; see USB_STORAGE Help for more information
+#
+
+#
+# USB Gadget Support
+#
+# CONFIG_USB_GADGET is not set
+
+#
+# MMC/SD Card support
+#
+# CONFIG_MMC is not set
+
+#
+# Synchronous Serial Interfaces (SSI)
+#
+
+#
+# File systems
+#
+CONFIG_EXT2_FS=y
+CONFIG_EXT2_FS_XATTR=y
+CONFIG_EXT2_FS_POSIX_ACL=y
+CONFIG_EXT2_FS_SECURITY=y
+# CONFIG_EXT3_FS is not set
+# CONFIG_JBD is not set
+CONFIG_FS_MBCACHE=y
+# CONFIG_REISERFS_FS is not set
+# CONFIG_JFS_FS is not set
+CONFIG_FS_POSIX_ACL=y
+# CONFIG_XFS_FS is not set
+# CONFIG_MINIX_FS is not set
+# CONFIG_ROMFS_FS is not set
+# CONFIG_QUOTA is not set
+# CONFIG_DNOTIFY is not set
+# CONFIG_AUTOFS_FS is not set
+# CONFIG_AUTOFS4_FS is not set
+
+#
+# CD-ROM/DVD Filesystems
+#
+# CONFIG_ISO9660_FS is not set
+# CONFIG_UDF_FS is not set
+
+#
+# DOS/FAT/NT Filesystems
+#
+CONFIG_FAT_FS=y
+CONFIG_MSDOS_FS=y
+CONFIG_VFAT_FS=y
+CONFIG_FAT_DEFAULT_CODEPAGE=437
+CONFIG_FAT_DEFAULT_IOCHARSET="iso8859-1"
+CONFIG_NTFS_FS=m
+# CONFIG_NTFS_DEBUG is not set
+# CONFIG_NTFS_RW is not set
+
+#
+# Pseudo filesystems
+#
+CONFIG_PROC_FS=y
+CONFIG_PROC_KCORE=y
+CONFIG_SYSFS=y
+# CONFIG_DEVFS_FS is not set
+CONFIG_DEVPTS_FS_XATTR=y
+CONFIG_DEVPTS_FS_SECURITY=y
+CONFIG_TMPFS=y
+CONFIG_TMPFS_XATTR=y
+CONFIG_TMPFS_SECURITY=y
+# CONFIG_HUGETLBFS is not set
+# CONFIG_HUGETLB_PAGE is not set
+CONFIG_RAMFS=y
+# CONFIG_RELAYFS_FS is not set
+
+#
+# Miscellaneous filesystems
+#
+# CONFIG_ADFS_FS is not set
+# CONFIG_AFFS_FS is not set
+# CONFIG_HFS_FS is not set
+# CONFIG_HFSPLUS_FS is not set
+# CONFIG_BEFS_FS is not set
+# CONFIG_BFS_FS is not set
+# CONFIG_EFS_FS is not set
+# CONFIG_JFFS_FS is not set
+CONFIG_JFFS2_FS=y
+CONFIG_JFFS2_FS_DEBUG=0
+CONFIG_JFFS2_FS_WRITEBUFFER=y
+CONFIG_JFFS2_COMPRESSION_OPTIONS=y
+CONFIG_JFFS2_ZLIB=y
+CONFIG_JFFS2_RTIME=y
+# CONFIG_JFFS2_RUBIN is not set
+# CONFIG_JFFS2_CMODE_NONE is not set
+CONFIG_JFFS2_CMODE_PRIORITY=y
+# CONFIG_JFFS2_CMODE_SIZE is not set
+# CONFIG_CRAMFS is not set
+# CONFIG_VXFS_FS is not set
+# CONFIG_HPFS_FS is not set
+# CONFIG_QNX4FS_FS is not set
+# CONFIG_SYSV_FS is not set
+# CONFIG_UFS_FS is not set
+# CONFIG_YAFFS_FS is not set
+# CONFIG_YAFFS1_FS is not set
+
+#
+# Network File Systems
+#
+CONFIG_NFS_FS=y
+CONFIG_NFS_V3=y
+CONFIG_NFS_V4=y
+CONFIG_NFS_DIRECTIO=y
+# CONFIG_NFSD is not set
+CONFIG_ROOT_NFS=y
+CONFIG_LOCKD=y
+CONFIG_LOCKD_V4=y
+# CONFIG_EXPORTFS is not set
+CONFIG_SUNRPC=y
+CONFIG_SUNRPC_GSS=y
+CONFIG_RPCSEC_GSS_KRB5=y
+# CONFIG_RPCSEC_GSS_SPKM3 is not set
+# CONFIG_SMB_FS is not set
+# CONFIG_CIFS is not set
+# CONFIG_NCP_FS is not set
+# CONFIG_CODA_FS is not set
+# CONFIG_AFS_FS is not set
+
+#
+# Partition Types
+#
+# CONFIG_PARTITION_ADVANCED is not set
+CONFIG_MSDOS_PARTITION=y
+
+#
+# Native Language Support
+#
+CONFIG_NLS=y
+CONFIG_NLS_DEFAULT=""
+# CONFIG_NLS_CODEPAGE_437 is not set
+# CONFIG_NLS_CODEPAGE_737 is not set
+# CONFIG_NLS_CODEPAGE_775 is not set
+# CONFIG_NLS_CODEPAGE_850 is not set
+# CONFIG_NLS_CODEPAGE_852 is not set
+# CONFIG_NLS_CODEPAGE_855 is not set
+# CONFIG_NLS_CODEPAGE_857 is not set
+# CONFIG_NLS_CODEPAGE_860 is not set
+# CONFIG_NLS_CODEPAGE_861 is not set
+# CONFIG_NLS_CODEPAGE_862 is not set
+# CONFIG_NLS_CODEPAGE_863 is not set
+# CONFIG_NLS_CODEPAGE_864 is not set
+# CONFIG_NLS_CODEPAGE_865 is not set
+# CONFIG_NLS_CODEPAGE_866 is not set
+# CONFIG_NLS_CODEPAGE_869 is not set
+# CONFIG_NLS_CODEPAGE_936 is not set
+# CONFIG_NLS_CODEPAGE_950 is not set
+# CONFIG_NLS_CODEPAGE_932 is not set
+# CONFIG_NLS_CODEPAGE_949 is not set
+# CONFIG_NLS_CODEPAGE_874 is not set
+# CONFIG_NLS_ISO8859_8 is not set
+# CONFIG_NLS_CODEPAGE_1250 is not set
+# CONFIG_NLS_CODEPAGE_1251 is not set
+# CONFIG_NLS_ASCII is not set
+# CONFIG_NLS_ISO8859_1 is not set
+# CONFIG_NLS_ISO8859_2 is not set
+# CONFIG_NLS_ISO8859_3 is not set
+# CONFIG_NLS_ISO8859_4 is not set
+# CONFIG_NLS_ISO8859_5 is not set
+# CONFIG_NLS_ISO8859_6 is not set
+# CONFIG_NLS_ISO8859_7 is not set
+# CONFIG_NLS_ISO8859_9 is not set
+# CONFIG_NLS_ISO8859_13 is not set
+# CONFIG_NLS_ISO8859_14 is not set
+# CONFIG_NLS_ISO8859_15 is not set
+# CONFIG_NLS_KOI8_R is not set
+# CONFIG_NLS_KOI8_U is not set
+# CONFIG_NLS_UTF8 is not set
+
+#
+# Profiling support
+#
+# CONFIG_PROFILING is not set
+
+#
+# Kernel hacking
+#
+# CONFIG_DEBUG_KERNEL=y
+# CONFIG_MAGIC_SYSRQ is not set
+# CONFIG_SCHEDSTATS is not set
+# CONFIG_DEBUG_SLAB is not set
+# CONFIG_DEBUG_PREEMPT is not set
+# CONFIG_DEBUG_SPINLOCK_SLEEP is not set
+# CONFIG_WAKEUP_TIMING is not set
+# CONFIG_CRITICAL_PREEMPT_TIMING is not set
+# CONFIG_CRITICAL_IRQSOFF_TIMING is not set
+#CONFIG_RT_DEADLOCK_DETECT=y
+#CONFIG_DEBUG_KOBJECT=y
+#CONFIG_DEBUG_INFO=y
+# CONFIG_KGDB is not set
+CONFIG_CROSSCOMPILE=y
+# CONFIG_CMDLINE=""
+# CONFIG_DEBUG_STACK_USAGE is not set
+# CONFIG_RUNTIME_DEBUG is not set
+# CONFIG_MIPS_UNCACHED is not set
+
+#
+# Security options
+#
+# CONFIG_KEYS is not set
+# CONFIG_SECURITY is not set
+
+#
+# Cryptographic options
+#
+CONFIG_CRYPTO=y
+CONFIG_CRYPTO_HMAC=y
+# CONFIG_CRYPTO_NULL is not set
+# CONFIG_CRYPTO_MD4 is not set
+CONFIG_CRYPTO_MD5=y
+# CONFIG_CRYPTO_SHA1 is not set
+# CONFIG_CRYPTO_SHA256 is not set
+# CONFIG_CRYPTO_SHA512 is not set
+# CONFIG_CRYPTO_WP512 is not set
+CONFIG_CRYPTO_DES=y
+# CONFIG_CRYPTO_BLOWFISH is not set
+# CONFIG_CRYPTO_TWOFISH is not set
+# CONFIG_CRYPTO_SERPENT is not set
+# CONFIG_CRYPTO_AES is not set
+# CONFIG_CRYPTO_CAST5 is not set
+# CONFIG_CRYPTO_CAST6 is not set
+# CONFIG_CRYPTO_TEA is not set
+# CONFIG_CRYPTO_ARC4 is not set
+# CONFIG_CRYPTO_KHAZAD is not set
+# CONFIG_CRYPTO_ANUBIS is not set
+# CONFIG_CRYPTO_DEFLATE is not set
+# CONFIG_CRYPTO_MICHAEL_MIC is not set
+# CONFIG_CRYPTO_CRC32C is not set
+# CONFIG_CRYPTO_TEST is not set
+
+#
+# Library routines
+#
+# CONFIG_CRC_CCITT is not set
+CONFIG_CRC32=y
+# CONFIG_LIBCRC32C is not set
+CONFIG_ZLIB_INFLATE=y
+CONFIG_ZLIB_DEFLATE=y
+
+#
+# Fast Real-Time Domain
+#
+# CONFIG_FRD is not set
+
+#
+# Fast Real-Time Domain Advanced Options
+#
+CONFIG_GENERIC_HARDIRQS=y
+CONFIG_GENERIC_IRQ_PROBE=y
Index: linux-2.6.10/arch/mips/emma2rh/common/irq.c
===================================================================
--- /dev/null
+++ linux-2.6.10/arch/mips/emma2rh/common/irq.c
@@ -0,0 +1,108 @@
+/*
+ * arch/mips/emma2rh/common/irq.c
+ * This file is common irq dispatcher.
+ *
+ * Copyright (C) NEC Electronics Corporation 2005-2006
+ *
+ * This file is based on the arch/mips/ddb5xxx/ddb5477/irq.c
+ *
+ * Copyright 2001 MontaVista Software Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
+ */
+#include <linux/config.h>
+#include <linux/init.h>
+#include <linux/interrupt.h>
+#include <linux/irq.h>
+#include <linux/types.h>
+
+#include <asm/i8259.h>
+#include <asm/system.h>
+#include <asm/mipsregs.h>
+#include <asm/debug.h>
+#include <asm/addrspace.h>
+#include <asm/bootinfo.h>
+
+#include <asm/emma2rh/emma2rh.h>
+
+/*
+ * the first level int-handler will jump here if it is a emma2rh irq
+ */
+asmlinkage void emma2rh_irq_dispatch(struct pt_regs *regs)
+{
+ u32 intStatus;
+ u32 bitmask;
+ u32 i;
+
+ intStatus = emma2rh_in32(EMMA2RH_BHIF_INT_ST_0)
+ & emma2rh_in32(EMMA2RH_BHIF_INT_EN_0);
+
+#ifdef EMMA2RH_SW_CASCADE
+ if (intStatus &
+ (1 << ((EMMA2RH_SW_CASCADE - EMMA2RH_IRQ_INT0) & (32 - 1)))) {
+ u32 swIntStatus;
+ swIntStatus = emma2rh_in32(EMMA2RH_BHIF_SW_INT)
+ & emma2rh_in32(EMMA2RH_BHIF_SW_INT_EN);
+ for (i = 0, bitmask = 1; i < 32; i++, bitmask <<= 1) {
+ if (swIntStatus & bitmask) {
+ do_IRQ(EMMA2RH_SW_IRQ_BASE + i, regs);
+ return;
+ }
+ }
+ }
+#endif
+
+ for (i = 0, bitmask = 1; i < 32; i++, bitmask <<= 1) {
+ if (intStatus & bitmask) {
+ do_IRQ(EMMA2RH_IRQ_BASE + i, regs);
+ return;
+ }
+ }
+
+ intStatus = emma2rh_in32(EMMA2RH_BHIF_INT_ST_1)
+ & emma2rh_in32(EMMA2RH_BHIF_INT_EN_1);
+
+#ifdef EMMA2RH_GPIO_CASCADE
+ if (intStatus &
+ (1 << ((EMMA2RH_GPIO_CASCADE - EMMA2RH_IRQ_INT0) & (32 - 1)))) {
+ u32 gpioIntStatus;
+ gpioIntStatus = emma2rh_in32(EMMA2RH_GPIO_INT_ST)
+ & emma2rh_in32(EMMA2RH_GPIO_INT_MASK);
+ for (i = 0, bitmask = 1; i < 32; i++, bitmask <<= 1) {
+ if (gpioIntStatus & bitmask) {
+ do_IRQ(EMMA2RH_GPIO_IRQ_BASE + i, regs);
+ return;
+ }
+ }
+ }
+#endif
+
+ for (i = 32, bitmask = 1; i < 64; i++, bitmask <<= 1) {
+ if (intStatus & bitmask) {
+ do_IRQ(EMMA2RH_IRQ_BASE + i, regs);
+ return;
+ }
+ }
+
+ intStatus = emma2rh_in32(EMMA2RH_BHIF_INT_ST_2)
+ & emma2rh_in32(EMMA2RH_BHIF_INT_EN_2);
+
+ for (i = 64, bitmask = 1; i < 96; i++, bitmask <<= 1) {
+ if (intStatus & bitmask) {
+ do_IRQ(EMMA2RH_IRQ_BASE + i, regs);
+ return;
+ }
+ }
+}
Index: linux-2.6.10/arch/mips/emma2rh/common/irq_emma2rh.c
===================================================================
--- /dev/null
+++ linux-2.6.10/arch/mips/emma2rh/common/irq_emma2rh.c
@@ -0,0 +1,135 @@
+/*
+ * arch/mips/emma2rh/common/irq_emma2rh.c
+ * This file defines the irq handler for EMMA2RH.
+ *
+ * Copyright (C) NEC Electronics Corporation 2005-2006
+ *
+ * This file is based on the arch/mips/ddb5xxx/ddb5477/irq_5477.c
+ *
+ * Copyright 2001 MontaVista Software Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
+ */
+
+/*
+ * EMMA2RH defines 64 IRQs.
+ *
+ * This file exports one function:
+ * emma2rh_irq_init(u32 irq_base);
+ */
+
+#include <linux/interrupt.h>
+#include <linux/types.h>
+#include <linux/ptrace.h>
+
+#include <asm/debug.h>
+
+#include <asm/emma2rh/emma2rh.h>
+
+/* number of total irqs supported by EMMA2RH */
+#define NUM_EMMA2RH_IRQ 96
+
+static int emma2rh_irq_base = -1;
+
+void ll_emma2rh_irq_enable(int);
+void ll_emma2rh_irq_disable(int);
+
+static void emma2rh_irq_enable(unsigned int irq)
+{
+ ll_emma2rh_irq_enable(irq - emma2rh_irq_base);
+}
+
+static void emma2rh_irq_disable(unsigned int irq)
+{
+ ll_emma2rh_irq_disable(irq - emma2rh_irq_base);
+}
+
+static unsigned int emma2rh_irq_startup(unsigned int irq)
+{
+ emma2rh_irq_enable(irq);
+ return 0;
+}
+
+#define emma2rh_irq_shutdown emma2rh_irq_disable
+
+static void emma2rh_irq_ack(unsigned int irq)
+{
+ /* disable interrupt - some handler will re-enable the irq
+ * and if the interrupt is leveled, we will have infinite loop
+ */
+ ll_emma2rh_irq_disable(irq - emma2rh_irq_base);
+}
+
+static void emma2rh_irq_end(unsigned int irq)
+{
+ if (!(irq_desc[irq].status & (IRQ_DISABLED | IRQ_INPROGRESS)))
+ ll_emma2rh_irq_enable(irq - emma2rh_irq_base);
+}
+
+hw_irq_controller emma2rh_irq_controller = {
+ .typename = "emma2rh_irq",
+ .startup = emma2rh_irq_startup,
+ .shutdown = emma2rh_irq_shutdown,
+ .enable = emma2rh_irq_enable,
+ .disable = emma2rh_irq_disable,
+ .ack = emma2rh_irq_ack,
+ .end = emma2rh_irq_end,
+ .set_affinity = NULL /* no affinity stuff for UP */
+};
+
+void emma2rh_irq_init(u32 irq_base)
+{
+ extern irq_desc_t irq_desc[];
+ u32 i;
+
+ for (i = irq_base; i < irq_base + NUM_EMMA2RH_IRQ; i++) {
+ irq_desc[i].status = IRQ_DISABLED;
+ irq_desc[i].action = NULL;
+ irq_desc[i].depth = 1;
+ irq_desc[i].handler = &emma2rh_irq_controller;
+ }
+
+ emma2rh_irq_base = irq_base;
+}
+
+void ll_emma2rh_irq_enable(int emma2rh_irq)
+{
+ u32 reg_value;
+ u32 reg_bitmask;
+ u32 reg_index;
+
+ reg_index = EMMA2RH_BHIF_INT_EN_0
+ + (EMMA2RH_BHIF_INT_EN_1 - EMMA2RH_BHIF_INT_EN_0)
+ * (emma2rh_irq / 32);
+ reg_value = emma2rh_in32(reg_index);
+ reg_bitmask = 0x1 << (emma2rh_irq % 32);
+ db_assert((reg_value & reg_bitmask) == 0);
+ emma2rh_out32(reg_index, reg_value | reg_bitmask);
+}
+
+void ll_emma2rh_irq_disable(int emma2rh_irq)
+{
+ u32 reg_value;
+ u32 reg_bitmask;
+ u32 reg_index;
+
+ reg_index = EMMA2RH_BHIF_INT_EN_0
+ + (EMMA2RH_BHIF_INT_EN_1 - EMMA2RH_BHIF_INT_EN_0)
+ * (emma2rh_irq / 32);
+ reg_value = emma2rh_in32(reg_index);
+ reg_bitmask = 0x1 << (emma2rh_irq % 32);
+ db_assert((reg_value & reg_bitmask) != 0);
+ emma2rh_out32(reg_index, reg_value & ~reg_bitmask);
+}
Index: linux-2.6.10/arch/mips/emma2rh/common/Makefile
===================================================================
--- /dev/null
+++ linux-2.6.10/arch/mips/emma2rh/common/Makefile
@@ -0,0 +1,13 @@
+#
+# arch/mips/emma2rh/common/Makefile
+# Makefile for the common code of NEC EMMA2RH based board.
+#
+# Copyright (C) NEC Electronics Corporation 2005-2006
+#
+# This program is free software; you can redistribute it and/or modify
+# it under the terms of the GNU General Public License as published by
+# the Free Software Foundation; either version 2 of the License, or
+# (at your option) any later version.
+#
+
+obj-$(CONFIG_MARKEINS) += irq.o irq_emma2rh.o prom.o
Index: linux-2.6.10/arch/mips/emma2rh/common/prom.c
===================================================================
--- /dev/null
+++ linux-2.6.10/arch/mips/emma2rh/common/prom.c
@@ -0,0 +1,77 @@
+/*
+ * arch/mips/emma2rh/common/prom.c
+ * This file is prom file.
+ *
+ * Copyright (C) NEC Electronics Corporation 2004-2006
+ *
+ * This file is based on the arch/mips/ddb5xxx/common/prom.c
+ *
+ * Copyright 2001 MontaVista Software Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
+ */
+#include <linux/config.h>
+#include <linux/init.h>
+#include <linux/mm.h>
+#include <linux/sched.h>
+#include <linux/bootmem.h>
+
+#include <asm/addrspace.h>
+#include <asm/bootinfo.h>
+#include <asm/emma2rh/emma2rh.h>
+#include <asm/debug.h>
+
+const char *get_system_type(void)
+{
+ switch (mips_machtype) {
+ case MACH_NEC_MARKEINS:
+ return "NEC EMMA2RH Mark-eins";
+ default:
+ return "Unknown NEC board";
+ }
+}
+
+/* [jsun@xxxxxxxxxx] PMON passes arguments in C main() style */
+void __init prom_init(void)
+{
+ int argc = fw_arg0;
+ char **arg = (char **)fw_arg1;
+ int i;
+
+ /* if user passes kernel args, ignore the default one */
+ if (argc > 1)
+ arcs_cmdline[0] = '\0';
+
+ /* arg[0] is "g", the rest is boot parameters */
+ for (i = 1; i < argc; i++) {
+ if (strlen(arcs_cmdline) + strlen(arg[i] + 1)
+ >= sizeof(arcs_cmdline))
+ break;
+ strcat(arcs_cmdline, arg[i]);
+ strcat(arcs_cmdline, " ");
+ }
+
+ mips_machgroup = MACH_GROUP_NEC_EMMA2RH;
+
+#if defined(CONFIG_MARKEINS)
+ mips_machtype = MACH_NEC_MARKEINS;
+ add_memory_region(0, EMMA2RH_RAM_SIZE, BOOT_MEM_RAM);
+#endif
+
+}
+
+void __init prom_free_prom_memory(void)
+{
+}
Index: linux-2.6.10/arch/mips/emma2rh/markeins/int-handler.S
===================================================================
--- /dev/null
+++ linux-2.6.10/arch/mips/emma2rh/markeins/int-handler.S
@@ -0,0 +1,88 @@
+/*
+ * arch/mips/emma2rh/markeins/int-handler.S
+ * first level dispatcher for EMMA2RH Mark-eins.
+ *
+ * Copyright (C) NEC Electronics Corporation 2004-2006
+ *
+ * This file is based on the arch/mips/ddb5xxx/ddb5477/int-handler.S
+ *
+ * Copyright 2001 MontaVista Software Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
+ */
+#include <asm/asm.h>
+#include <asm/mipsregs.h>
+#include <asm/addrspace.h>
+#include <asm/regdef.h>
+#include <asm/stackframe.h>
+#include <asm/emma2rh/emma2rh.h>
+
+/*
+ * first level interrupt dispatcher for Mark-eins board -
+ * We check for the timer first, then check PCI ints A and D.
+ * Then check for serial IRQ and fall through.
+ */
+ .align 5
+ NESTED(emma2rh_handle_int, PT_SIZE, sp)
+ SAVE_ALL
+ CLI
+ .set at
+ .set noreorder
+ mfc0 t0, CP0_CAUSE
+ mfc0 t2, CP0_STATUS
+
+ and t0, t2
+
+ andi t1, t0, STATUSF_IP7 /* cpu timer */
+ bnez t1, ll_cputimer_irq
+ andi t1, t0, STATUSF_IP2 /* emma2rh int 2 */
+ bnez t1, ll_emma2rh_irq
+ andi t1, t0, STATUSF_IP1 /* software int 1 */
+ bnez t1, ll_cpu_ip1
+ andi t1, t0, STATUSF_IP0 /* software int 0 */
+ bnez t1, ll_cpu_ip0
+ nop
+ .set reorder
+
+ /* wrong alarm or masked ... */
+ j spurious_interrupt
+ nop
+ END(emma2rh_handle_int)
+
+ .align 5
+
+ll_emma2rh_irq:
+ move a0, sp
+ jal emma2rh_irq_dispatch
+ j ret_from_irq
+
+ll_cputimer_irq:
+ li a0, CPU_IRQ_BASE + 7
+ move a1, sp
+ jal do_IRQ
+ j ret_from_irq
+
+
+ll_cpu_ip0:
+ li a0, CPU_IRQ_BASE + 0
+ move a1, sp
+ jal do_IRQ
+ j ret_from_irq
+
+ll_cpu_ip1:
+ li a0, CPU_IRQ_BASE + 1
+ move a1, sp
+ jal do_IRQ
+ j ret_from_irq
Index: linux-2.6.10/arch/mips/emma2rh/markeins/irq.c
===================================================================
--- /dev/null
+++ linux-2.6.10/arch/mips/emma2rh/markeins/irq.c
@@ -0,0 +1,112 @@
+/*
+ * arch/mips/emma2rh/markeins/irq.c
+ * This file defines the irq handler for EMMA2RH.
+ *
+ * Copyright (C) NEC Electronics Corporation 2004-2006
+ *
+ * This file is based on the arch/mips/ddb5xxx/ddb5477/irq.c
+ *
+ * Copyright 2001 MontaVista Software Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
+ */
+#include <linux/config.h>
+#include <linux/init.h>
+#include <linux/interrupt.h>
+#include <linux/irq.h>
+#include <linux/types.h>
+#include <linux/ptrace.h>
+
+#include <asm/i8259.h>
+#include <asm/system.h>
+#include <asm/mipsregs.h>
+#include <asm/debug.h>
+#include <asm/addrspace.h>
+#include <asm/bootinfo.h>
+
+#include <asm/emma2rh/emma2rh.h>
+
+/*
+ * IRQ mapping
+ *
+ * 0-7: 8 CPU interrupts
+ * 0 - software interrupt 0
+ * 1 - software interrupt 1
+ * 2 - most Vrc5477 interrupts are routed to this pin
+ * 3 - (optional) some other interrupts routed to this pin for debugg
+ * 4 - not used
+ * 5 - not used
+ * 6 - not used
+ * 7 - cpu timer (used by default)
+ *
+ */
+
+extern void emma2rh_sw_irq_init(u32 base);
+extern void emma2rh_gpio_irq_init(u32 base);
+extern void emma2rh_irq_init(u32 base);
+extern void mips_cpu_irq_init(u32 base);
+extern asmlinkage void emma2rh_handle_int(void);
+extern int setup_irq(unsigned int irq, struct irqaction *irqaction);
+static struct irqaction irq_cascade =
+ { no_action, 0, CPU_MASK_NONE, "cascade", NULL, NULL };
+
+void __init arch_init_irq(void)
+{
+ u32 reg;
+
+ db_run(printk("markeins_irq_setup invoked.\n"));
+
+ /* by default, interrupts are disabled. */
+ emma2rh_out32(EMMA2RH_BHIF_INT_EN_0, 0);
+ emma2rh_out32(EMMA2RH_BHIF_INT_EN_1, 0);
+ emma2rh_out32(EMMA2RH_BHIF_INT_EN_2, 0);
+ emma2rh_out32(EMMA2RH_BHIF_INT1_EN_0, 0);
+ emma2rh_out32(EMMA2RH_BHIF_INT1_EN_1, 0);
+ emma2rh_out32(EMMA2RH_BHIF_INT1_EN_2, 0);
+ emma2rh_out32(EMMA2RH_BHIF_SW_INT_EN, 0);
+
+ clear_c0_status(0xff00);
+ set_c0_status(0x0400);
+
+#define GPIO_PCI (0xf<<15)
+ /* setup GPIO interrupt for PCI interface */
+ /* direction input */
+ reg = emma2rh_in32(EMMA2RH_GPIO_DIR);
+ emma2rh_out32(EMMA2RH_GPIO_DIR, reg & ~GPIO_PCI);
+ /* disable interrupt */
+ reg = emma2rh_in32(EMMA2RH_GPIO_INT_MASK);
+ emma2rh_out32(EMMA2RH_GPIO_INT_MASK, reg & ~GPIO_PCI);
+ /* level triggerd */
+ reg = emma2rh_in32(EMMA2RH_GPIO_INT_MODE);
+ emma2rh_out32(EMMA2RH_GPIO_INT_MODE, reg | GPIO_PCI);
+ reg = emma2rh_in32(EMMA2RH_GPIO_INT_CND_A);
+ emma2rh_out32(EMMA2RH_GPIO_INT_CND_A, reg & (~GPIO_PCI));
+ /* interrupt clear */
+ emma2rh_out32(EMMA2RH_GPIO_INT_ST, ~GPIO_PCI);
+
+ /* init all controllers */
+ emma2rh_irq_init(EMMA2RH_IRQ_BASE);
+ emma2rh_sw_irq_init(EMMA2RH_SW_IRQ_BASE);
+ emma2rh_gpio_irq_init(EMMA2RH_GPIO_IRQ_BASE);
+ mips_cpu_irq_init(CPU_IRQ_BASE);
+
+ /* setup cascade interrupts */
+ setup_irq(EMMA2RH_IRQ_BASE + EMMA2RH_SW_CASCADE, &irq_cascade);
+ setup_irq(EMMA2RH_IRQ_BASE + EMMA2RH_GPIO_CASCADE, &irq_cascade);
+ setup_irq(CPU_IRQ_BASE + CPU_EMMA2RH_CASCADE, &irq_cascade);
+
+ /* hook up the first-level interrupt handler */
+ set_except_vector(0, emma2rh_handle_int);
+}
Index: linux-2.6.10/arch/mips/emma2rh/markeins/irq_markeins.c
===================================================================
--- /dev/null
+++ linux-2.6.10/arch/mips/emma2rh/markeins/irq_markeins.c
@@ -0,0 +1,198 @@
+/*
+ * arch/mips/emma2rh/markeins/irq_markeins.c
+ * This file defines the irq handler for Mark-eins.
+ *
+ * Copyright (C) NEC Electronics Corporation 2004-2006
+ *
+ * This file is based on the arch/mips/ddb5xxx/ddb5477/irq_5477.c
+ *
+ * Copyright 2001 MontaVista Software Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
+ */
+#include <linux/interrupt.h>
+#include <linux/types.h>
+#include <linux/ptrace.h>
+
+#include <asm/debug.h>
+#include <asm/emma2rh/emma2rh.h>
+
+static int emma2rh_sw_irq_base = -1;
+static int emma2rh_gpio_irq_base = -1;
+
+void ll_emma2rh_sw_irq_enable(int reg);
+void ll_emma2rh_sw_irq_disable(int reg);
+void ll_emma2rh_gpio_irq_enable(int reg);
+void ll_emma2rh_gpio_irq_disable(int reg);
+
+static void emma2rh_sw_irq_enable(unsigned int irq)
+{
+ ll_emma2rh_sw_irq_enable(irq - emma2rh_sw_irq_base);
+}
+
+static void emma2rh_sw_irq_disable(unsigned int irq)
+{
+ ll_emma2rh_sw_irq_disable(irq - emma2rh_sw_irq_base);
+}
+
+static unsigned int emma2rh_sw_irq_startup(unsigned int irq)
+{
+ emma2rh_sw_irq_enable(irq);
+ return 0;
+}
+
+#define emma2rh_sw_irq_shutdown emma2rh_sw_irq_disable
+
+static void emma2rh_sw_irq_ack(unsigned int irq)
+{
+ ll_emma2rh_sw_irq_disable(irq - emma2rh_sw_irq_base);
+}
+
+static void emma2rh_sw_irq_end(unsigned int irq)
+{
+ if (!(irq_desc[irq].status & (IRQ_DISABLED | IRQ_INPROGRESS)))
+ ll_emma2rh_sw_irq_enable(irq - emma2rh_sw_irq_base);
+}
+
+hw_irq_controller emma2rh_sw_irq_controller = {
+ .typename = "emma2rh_sw_irq",
+ .startup = emma2rh_sw_irq_startup,
+ .shutdown = emma2rh_sw_irq_shutdown,
+ .enable = emma2rh_sw_irq_enable,
+ .disable = emma2rh_sw_irq_disable,
+ .ack = emma2rh_sw_irq_ack,
+ .end = emma2rh_sw_irq_end,
+ .set_affinity = NULL,
+};
+
+void emma2rh_sw_irq_init(u32 irq_base)
+{
+ extern irq_desc_t irq_desc[];
+ u32 i;
+
+ for (i = irq_base; i < irq_base + NUM_EMMA2RH_IRQ_SW; i++) {
+ irq_desc[i].status = IRQ_DISABLED;
+ irq_desc[i].action = NULL;
+ irq_desc[i].depth = 2;
+ irq_desc[i].handler = &emma2rh_sw_irq_controller;
+ }
+
+ emma2rh_sw_irq_base = irq_base;
+}
+
+void ll_emma2rh_sw_irq_enable(int irq)
+{
+ u32 reg;
+
+ db_assert(irq >= 0);
+ db_assert(irq < NUM_EMMA2RH_IRQ_SW);
+
+ reg = emma2rh_in32(EMMA2RH_BHIF_SW_INT_EN);
+ reg |= 1 << irq;
+ emma2rh_out32(EMMA2RH_BHIF_SW_INT_EN, reg);
+}
+
+void ll_emma2rh_sw_irq_disable(int irq)
+{
+ u32 reg;
+
+ db_assert(irq >= 0);
+ db_assert(irq < 32);
+
+ reg = emma2rh_in32(EMMA2RH_BHIF_SW_INT_EN);
+ reg &= ~(1 << irq);
+ emma2rh_out32(EMMA2RH_BHIF_SW_INT_EN, reg);
+}
+
+static void emma2rh_gpio_irq_enable(unsigned int irq)
+{
+ ll_emma2rh_gpio_irq_enable(irq - emma2rh_gpio_irq_base);
+}
+
+static void emma2rh_gpio_irq_disable(unsigned int irq)
+{
+ ll_emma2rh_gpio_irq_disable(irq - emma2rh_gpio_irq_base);
+}
+
+static unsigned int emma2rh_gpio_irq_startup(unsigned int irq)
+{
+ emma2rh_gpio_irq_enable(irq);
+ return 0;
+}
+
+#define emma2rh_gpio_irq_shutdown emma2rh_gpio_irq_disable
+
+static void emma2rh_gpio_irq_ack(unsigned int irq)
+{
+ irq -= emma2rh_gpio_irq_base;
+ emma2rh_out32(EMMA2RH_GPIO_INT_ST, ~(1 << irq));
+ ll_emma2rh_gpio_irq_disable(irq);
+}
+
+static void emma2rh_gpio_irq_end(unsigned int irq)
+{
+ if (!(irq_desc[irq].status & (IRQ_DISABLED | IRQ_INPROGRESS)))
+ ll_emma2rh_gpio_irq_enable(irq - emma2rh_gpio_irq_base);
+}
+
+hw_irq_controller emma2rh_gpio_irq_controller = {
+ .typename = "emma2rh_gpio_irq",
+ .startup = emma2rh_gpio_irq_startup,
+ .shutdown = emma2rh_gpio_irq_shutdown,
+ .enable = emma2rh_gpio_irq_enable,
+ .disable = emma2rh_gpio_irq_disable,
+ .ack = emma2rh_gpio_irq_ack,
+ .end = emma2rh_gpio_irq_end,
+ .set_affinity = NULL,
+};
+
+void emma2rh_gpio_irq_init(u32 irq_base)
+{
+ extern irq_desc_t irq_desc[];
+ u32 i;
+
+ for (i = irq_base; i < irq_base + NUM_EMMA2RH_IRQ_GPIO; i++) {
+ irq_desc[i].status = IRQ_DISABLED;
+ irq_desc[i].action = NULL;
+ irq_desc[i].depth = 2;
+ irq_desc[i].handler = &emma2rh_gpio_irq_controller;
+ }
+
+ emma2rh_gpio_irq_base = irq_base;
+}
+
+void ll_emma2rh_gpio_irq_enable(int irq)
+{
+ u32 reg;
+
+ db_assert(irq >= 0);
+ db_assert(irq < NUM_EMMA2RH_IRQ_GPIO);
+
+ reg = emma2rh_in32(EMMA2RH_GPIO_INT_MASK);
+ reg |= 1 << irq;
+ emma2rh_out32(EMMA2RH_GPIO_INT_MASK, reg);
+}
+
+void ll_emma2rh_gpio_irq_disable(int irq)
+{
+ u32 reg;
+
+ db_assert(irq >= 0);
+ db_assert(irq < NUM_EMMA2RH_IRQ_GPIO);
+
+ reg = emma2rh_in32(EMMA2RH_GPIO_INT_MASK);
+ reg &= ~(1 << irq);
+ emma2rh_out32(EMMA2RH_GPIO_INT_MASK, reg);
+}
Index: linux-2.6.10/arch/mips/emma2rh/markeins/led.c
===================================================================
--- /dev/null
+++ linux-2.6.10/arch/mips/emma2rh/markeins/led.c
@@ -0,0 +1,60 @@
+/*
+ * arch/mips/emma2rh/markeins/led.c
+ * This file defines the led display for Mark-eins.
+ *
+ * Copyright (C) NEC Electronics Corporation 2004-2006
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
+ */
+#include <linux/kernel.h>
+#include <linux/types.h>
+#include <linux/string.h>
+#include <asm/emma2rh/emma2rh.h>
+
+const unsigned long clear = 0x20202020;
+
+#define LED_BASE 0xb1400038
+
+void markeins_led_clear(void)
+{
+ emma2rh_out32(LED_BASE, clear);
+ emma2rh_out32(LED_BASE + 4, clear);
+}
+
+void markeins_led(const char *str)
+{
+ int i;
+ int len = strlen(str);
+
+ markeins_led_clear();
+ if (len > 8)
+ len = 8;
+
+ if (emma2rh_in32(0xb0000800) & (0x1 << 18))
+ for (i = 0; i < len; i++)
+ emma2rh_out8(LED_BASE + i, str[i]);
+ else
+ for (i = 0; i < len; i++)
+ emma2rh_out8(LED_BASE + (i & 4) + (3 - (i & 3)),
+ str[i]);
+}
+
+void markeins_led_hex(u32 val)
+{
+ char str[10];
+
+ sprintf(str, "%08x", val);
+ markeins_led(str);
+}
Index: linux-2.6.10/arch/mips/emma2rh/markeins/Makefile
===================================================================
--- /dev/null
+++ linux-2.6.10/arch/mips/emma2rh/markeins/Makefile
@@ -0,0 +1,14 @@
+#
+# arch/mips/emma2rh/markeins/Makefile
+# Makefile for the common code of NEC EMMA2RH based board.
+#
+# Copyright (C) NEC Electronics Corporation 2005-2006
+#
+# This program is free software; you can redistribute it and/or modify
+# it under the terms of the GNU General Public License as published by
+# the Free Software Foundation; either version 2 of the License, or
+# (at your option) any later version.
+#
+
+obj-$(CONFIG_MARKEINS) += int-handler.o irq.o irq_markeins.o setup.o led.o platform.o
+# EXTRA_AFLAGS := $(CFLAGS)
Index: linux-2.6.10/arch/mips/emma2rh/markeins/setup.c
===================================================================
--- /dev/null
+++ linux-2.6.10/arch/mips/emma2rh/markeins/setup.c
@@ -0,0 +1,173 @@
+/*
+ * arch/mips/emma2rh/markeins/setup.c
+ * This file is setup for EMMA2RH Mark-eins.
+ *
+ * Copyright (C) NEC Electronics Corporation 2004-2006
+ *
+ * This file is based on the arch/mips/ddb5xxx/ddb5477/setup.c.
+ *
+ * Copyright 2001 MontaVista Software Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
+ */
+#include <linux/config.h>
+#include <linux/init.h>
+#include <linux/kernel.h>
+#include <linux/kdev_t.h>
+#include <linux/types.h>
+#include <linux/sched.h>
+#include <linux/pci.h>
+#include <linux/ide.h>
+#include <linux/fs.h> /* for ROOT_DEV */
+#include <linux/ioport.h>
+#include <linux/param.h> /* for HZ */
+#include <linux/major.h>
+#include <linux/kdev_t.h>
+#include <linux/root_dev.h>
+#include <linux/serial_8250.h>
+
+#include <asm/cpu.h>
+#include <asm/bootinfo.h>
+#include <asm/addrspace.h>
+#include <asm/time.h>
+#include <asm/bcache.h>
+#include <asm/irq.h>
+#include <asm/reboot.h>
+#include <asm/gdb-stub.h>
+#include <asm/traps.h>
+#include <asm/debug.h>
+
+#include <asm/emma2rh/emma2rh.h>
+
+#define USE_CPU_COUNTER_TIMER /* whether we use cpu counter */
+
+extern void markeins_led(const char *);
+
+static int bus_frequency = 0;
+
+static void markeins_machine_restart(char *command)
+{
+ static void (*back_to_prom) (void) = (void (*)(void))0xbfc00000;
+
+ printk("cannot EMMA2RH Mark-eins restart.\n");
+ markeins_led("restart.");
+ back_to_prom();
+}
+
+static void markeins_machine_halt(void)
+{
+ printk("EMMA2RH Mark-eins halted.\n");
+ markeins_led("halted.");
+ while (1) ;
+}
+
+static void markeins_machine_power_off(void)
+{
+ printk("EMMA2RH Mark-eins halted. Please turn off the power.\n");
+ markeins_led("poweroff.");
+ while (1) ;
+}
+
+static unsigned long clock[4] = { 166500000, 187312500, 199800000, 210600000 };
+
+static unsigned int __init detect_bus_frequency(unsigned long rtc_base)
+{
+ u32 reg;
+
+ /* detect from boot strap */
+ reg = emma2rh_in32(EMMA2RH_BHIF_STRAP_0);
+ reg = (reg >> 4) & 0x3;
+ return clock[reg];
+}
+
+static void __init emma2rh_time_init(void)
+{
+ u32 reg;
+ if (bus_frequency == 0)
+ bus_frequency = detect_bus_frequency(0);
+
+ reg = emma2rh_in32(EMMA2RH_BHIF_STRAP_0);
+ if ((reg & 0x3) == 0)
+ reg = (reg >> 6) & 0x3;
+ else {
+ reg = emma2rh_in32(EMMA2RH_BHIF_MAIN_CTRL);
+ reg = (reg >> 4) & 0x3;
+ }
+ mips_hpt_frequency = (bus_frequency * (4 + reg)) / 4 / 2;
+}
+
+extern int setup_irq(unsigned int irq, struct irqaction *irqaction);
+
+static void __init emma2rh_timer_setup(struct irqaction *irq)
+{
+ /* we are using the cpu counter for timer interrupts */
+ setup_irq(CPU_IRQ_BASE + 7, irq);
+}
+
+static void markeins_board_init(void);
+extern void markeins_irq_setup(void);
+
+#if defined(CONFIG_BLK_DEV_INITRD)
+extern unsigned long __rd_start, __rd_end, initrd_start, initrd_end;
+#endif
+
+int __init platform_setup(void)
+{
+ extern int panic_timeout;
+
+ /* initialize board - we don't trust the loader */
+ markeins_board_init();
+
+ set_io_port_base(KSEG1ADDR(EMMA2RH_PCI_IO_BASE));
+
+ board_time_init = emma2rh_time_init;
+ board_timer_setup = emma2rh_timer_setup;
+
+ _machine_restart = markeins_machine_restart;
+ _machine_halt = markeins_machine_halt;
+ _machine_power_off = markeins_machine_power_off;
+
+ /* setup resource limits */
+ ioport_resource.start = EMMA2RH_PCI_IO_BASE;
+ ioport_resource.end = EMMA2RH_PCI_IO_BASE + EMMA2RH_PCI_IO_SIZE - 1;
+ iomem_resource.start = EMMA2RH_IO_BASE;
+ iomem_resource.end = EMMA2RH_PCI_MEM_BASE + EMMA2RH_PCI_MEM_SIZE - 1;
+
+ /* Reboot on panic */
+ panic_timeout = 180;
+
+#if defined(CONFIG_BLK_DEV_INITRD)
+ ROOT_DEV = MKDEV(RAMDISK_MAJOR, 0);
+ initrd_start = (unsigned long)&__rd_start;
+ initrd_end = (unsigned long)&__rd_end;
+#endif
+
+ return 0;
+}
+
+static void __init markeins_board_init(void)
+{
+ u32 val;
+
+ val = emma2rh_in32(EMMA2RH_PBRD_INT_EN); /* open serial interrupts. */
+ emma2rh_out32(EMMA2RH_PBRD_INT_EN, val | 0xaa);
+ val = emma2rh_in32(EMMA2RH_PBRD_CLKSEL); /* set serial clocks. */
+ emma2rh_out32(EMMA2RH_PBRD_CLKSEL, val | 0x5); /* 18MHz */
+ emma2rh_out32(EMMA2RH_PCI_CONTROL, 0);
+
+ markeins_led("MVL E2RH");
+}
+
+early_initcall(platform_setup);
Index: linux-2.6.10/arch/mips/Kconfig
===================================================================
--- linux-2.6.10.orig/arch/mips/Kconfig
+++ linux-2.6.10/arch/mips/Kconfig
@@ -516,6 +516,19 @@ config NEC_OSPREY
select DMA_NONCOHERENT
select IRQ_CPU
+config MARKEINS
+ bool "Support for NEC EMMA2RH Mark-eins"
+ select DMA_NONCOHERENT
+ select HW_HAS_PCI
+ select IRQ_CPU
+ select SWAP_IO_SPACE
+ help
+ This enables support for the R5432-based NEC Mark-eins
+ boards with R5500 CPU.
+
+ Features : kernel debugging, serial terminal, NFS root fs, on-board
+ ether port USB, PCI, etc.
+
config SGI_IP22
bool "Support for SGI IP22 (Indy/Indigo2)"
select ARC
@@ -1134,7 +1147,7 @@ config MIPS_DISABLE_OBSOLETE_IDE
config CPU_LITTLE_ENDIAN
bool "Generate little endian code"
default y if ACER_PICA_61 || CASIO_E55 || DDB5074 || DDB5476 || DDB5477 || MACH_DECSTATION || IBM_WORKPAD || LASAT || MIPS_COBALT || MIPS_ITE8172 || MIPS_IVR || SOC_AU1X00 || NEC_OSPREY || OLIVETTI_M700 || SNI_RM200_PCI || VICTOR_MPC30X || ZAO_CAPCELLA
- default n if MIPS_EV64120 || MIPS_EV96100 || MOMENCO_OCELOT || MOMENCO_OCELOT_G || SGI_IP22 || SGI_IP27 || SGI_IP32 || TOSHIBA_JMR3927 || CAVIUM_OCTEON_EBT3000
+ default n if MIPS_EV64120 || MIPS_EV96100 || MOMENCO_OCELOT || MOMENCO_OCELOT_G || SGI_IP22 || SGI_IP27 || SGI_IP32 || TOSHIBA_JMR3927 || CAVIUM_OCTEON_EBT3000 || MARKEINS
help
Some MIPS machines can be configured for either little or big endian
byte order. These modes require different kernels. Say Y if your
@@ -1198,6 +1211,11 @@ config SOC_PNX8550
config SWAP_IO_SPACE
bool
+config EMMA2RH
+ bool
+ depends on MARKEINS
+ default y
+
#
# Unfortunately not all GT64120 systems run the chip at the same clock.
# As the user for the clock rate and try to minimize the available options.
Index: linux-2.6.10/arch/mips/Makefile
===================================================================
--- linux-2.6.10.orig/arch/mips/Makefile
+++ linux-2.6.10/arch/mips/Makefile
@@ -177,7 +177,7 @@ cflags-$(CONFIG_CPU_MIPS64) += \
cflags-$(CONFIG_CPU_R5000) += \
$(call set_gccflags,r5000,mips4,r5000,mips4,mips2) \
- -Wa,--trap
+ -Wa,--trap
cflags-$(CONFIG_CPU_R5432) += \
$(call set_gccflags,r5400,mips4,r5000,mips4,mips2) \
@@ -577,6 +577,16 @@ load-$(CONFIG_PNX8550_JBS) += 0xffffffff
#
libs-$(CONFIG_PNX8550_STB810) += arch/mips/philips/pnx8550/stb810/
load-$(CONFIG_PNX8550_STB810) += 0xffffffff80060000
+# NEC EMMA2RH boards
+#
+core-$(CONFIG_EMMA2RH) += arch/mips/emma2rh/common/
+cflags-$(CONFIG_EMMA2RH) += -Iinclude/asm-mips/mach-emma2rh
+
+# NEC EMMA2RH Mark-eins
+core-$(CONFIG_MARKEINS) += arch/mips/emma2rh/markeins/
+load-$(CONFIG_MARKEINS) += 0xffffffff88100000
+
+#
#
# SGI IP22 (Indy/Indigo2)
@@ -816,7 +826,7 @@ archclean:
@$(MAKE) $(clean)=arch/mips/boot
@$(MAKE) $(clean)=arch/mips/lasat
-# Generate <asm/offset.h
+# Generate <asm/offset.h
#
# The default rule is suffering from funny problems on MIPS so we using our
# own ...
Index: linux-2.6.10/include/asm-mips/bootinfo.h
===================================================================
--- linux-2.6.10.orig/include/asm-mips/bootinfo.h
+++ linux-2.6.10/include/asm-mips/bootinfo.h
@@ -250,6 +250,12 @@
#define MACH_GROUP_VR5701 24 /* VR5701 */
#define MACH_VR5701_SG2 0 /* VR5701_SG2 */
+/*
+ * Valid machtype for group NEC EMMA2RH
+ */
+#define MACH_GROUP_NEC_EMMA2RH 25 /* NEC EMMA2RH (was 23) */
+#define MACH_NEC_MARKEINS 0 /* NEC EMMA2RH Mark-eins */
+
#define CL_SIZE COMMAND_LINE_SIZE
const char *get_system_type(void);
Index: linux-2.6.10/include/asm-mips/emma2rh/emma2rh.h
===================================================================
--- /dev/null
+++ linux-2.6.10/include/asm-mips/emma2rh/emma2rh.h
@@ -0,0 +1,332 @@
+/*
+ * include/asm-mips/emma2rh/emma2rh.h
+ * This file is EMMA2RH common header.
+ *
+ * Copyright (C) NEC Electronics Corporation 2005-2006
+ *
+ * This file based on include/asm-mips/ddb5xxx/ddb5xxx.h
+ * Copyright 2001 MontaVista Software Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
+ */
+#ifndef __ASM_EMMA2RH_EMMA2RH_H
+#define __ASM_EMMA2RH_EMMA2RH_H
+
+/*
+ * EMMA2RH registers
+ */
+#define REGBASE 0x10000000
+
+#define EMMA2RH_BHIF_STRAP_0 (0x000010+REGBASE)
+#define EMMA2RH_BHIF_INT_ST_0 (0x000030+REGBASE)
+#define EMMA2RH_BHIF_INT_ST_1 (0x000034+REGBASE)
+#define EMMA2RH_BHIF_INT_ST_2 (0x000038+REGBASE)
+#define EMMA2RH_BHIF_INT_EN_0 (0x000040+REGBASE)
+#define EMMA2RH_BHIF_INT_EN_1 (0x000044+REGBASE)
+#define EMMA2RH_BHIF_INT_EN_2 (0x000048+REGBASE)
+#define EMMA2RH_BHIF_INT1_EN_0 (0x000050+REGBASE)
+#define EMMA2RH_BHIF_INT1_EN_1 (0x000054+REGBASE)
+#define EMMA2RH_BHIF_INT1_EN_2 (0x000058+REGBASE)
+#define EMMA2RH_BHIF_SW_INT (0x000070+REGBASE)
+#define EMMA2RH_BHIF_SW_INT_EN (0x000080+REGBASE)
+#define EMMA2RH_BHIF_SW_INT_CLR (0x000090+REGBASE)
+#define EMMA2RH_BHIF_MAIN_CTRL (0x0000b4+REGBASE)
+#define EMMA2RH_BHIF_EXCEPT_VECT_BASE_ADDRESS (0x0000c0+REGBASE)
+#define EMMA2RH_GPIO_DIR (0x110d20+REGBASE)
+#define EMMA2RH_GPIO_INT_ST (0x110d30+REGBASE)
+#define EMMA2RH_GPIO_INT_MASK (0x110d3c+REGBASE)
+#define EMMA2RH_GPIO_INT_MODE (0x110d48+REGBASE)
+#define EMMA2RH_GPIO_INT_CND_A (0x110d54+REGBASE)
+#define EMMA2RH_GPIO_INT_CND_B (0x110d60+REGBASE)
+#define EMMA2RH_PBRD_INT_EN (0x100010+REGBASE)
+#define EMMA2RH_PBRD_CLKSEL (0x100028+REGBASE)
+#define EMMA2RH_PFUR0_BASE (0x101000+REGBASE)
+#define EMMA2RH_PFUR1_BASE (0x102000+REGBASE)
+#define EMMA2RH_PFUR2_BASE (0x103000+REGBASE)
+#define EMMA2RH_PIIC0_BASE (0x107000+REGBASE)
+#define EMMA2RH_PIIC1_BASE (0x108000+REGBASE)
+#define EMMA2RH_PIIC2_BASE (0x109000+REGBASE)
+#define EMMA2RH_PCI_CONTROL (0x200000+REGBASE)
+#define EMMA2RH_PCI_ARBIT_CTR (0x200004+REGBASE)
+#define EMMA2RH_PCI_IWIN0_CTR (0x200010+REGBASE)
+#define EMMA2RH_PCI_IWIN1_CTR (0x200014+REGBASE)
+#define EMMA2RH_PCI_INIT_ESWP (0x200018+REGBASE)
+#define EMMA2RH_PCI_INT (0x200020+REGBASE)
+#define EMMA2RH_PCI_INT_EN (0x200024+REGBASE)
+#define EMMA2RH_PCI_TWIN_CTR (0x200030+REGBASE)
+#define EMMA2RH_PCI_TWIN_BADR (0x200034+REGBASE)
+#define EMMA2RH_PCI_TWIN0_DADR (0x200038+REGBASE)
+#define EMMA2RH_PCI_TWIN1_DADR (0x20003c+REGBASE)
+
+/*
+ * Memory map (physical address)
+ *
+ * Note most of the following address must be properly aligned by the
+ * corresponding size. For example, if PCI_IO_SIZE is 16MB, then
+ * PCI_IO_BASE must be aligned along 16MB boundary.
+ */
+
+/* the actual ram size is detected at run-time */
+#define EMMA2RH_RAM_BASE 0x00000000
+#define EMMA2RH_RAM_SIZE 0x10000000 /* less than 256MB */
+
+#define EMMA2RH_IO_BASE 0x10000000
+#define EMMA2RH_IO_SIZE 0x01000000 /* 16 MB */
+
+#define EMMA2RH_GENERALIO_BASE 0x11000000
+#define EMMA2RH_GENERALIO_SIZE 0x01000000 /* 16 MB */
+
+#define EMMA2RH_PCI_IO_BASE 0x12000000
+#define EMMA2RH_PCI_IO_SIZE 0x02000000 /* 32 MB */
+
+#define EMMA2RH_PCI_MEM_BASE 0x14000000
+#define EMMA2RH_PCI_MEM_SIZE 0x08000000 /* 128 MB */
+
+#define EMMA2RH_ROM_BASE 0x1c000000
+#define EMMA2RH_ROM_SIZE 0x04000000 /* 64 MB */
+
+#define EMMA2RH_PCI_CONFIG_BASE EMMA2RH_PCI_IO_BASE
+#define EMMA2RH_PCI_CONFIG_SIZE EMMA2RH_PCI_IO_SIZE
+
+#define NUM_CPU_IRQ 8
+#define NUM_EMMA2RH_IRQ 96
+
+#define CPU_EMMA2RH_CASCADE 2
+#define EMMA2RH_IRQ_BASE 0
+
+/*
+ * emma2rh irq defs
+ */
+
+#define EMMA2RH_IRQ_INT0 (0 + EMMA2RH_IRQ_BASE)
+#define EMMA2RH_IRQ_INT1 (1 + EMMA2RH_IRQ_BASE)
+#define EMMA2RH_IRQ_INT2 (2 + EMMA2RH_IRQ_BASE)
+#define EMMA2RH_IRQ_INT3 (3 + EMMA2RH_IRQ_BASE)
+#define EMMA2RH_IRQ_INT4 (4 + EMMA2RH_IRQ_BASE)
+#define EMMA2RH_IRQ_INT5 (5 + EMMA2RH_IRQ_BASE)
+#define EMMA2RH_IRQ_INT6 (6 + EMMA2RH_IRQ_BASE)
+#define EMMA2RH_IRQ_INT7 (7 + EMMA2RH_IRQ_BASE)
+#define EMMA2RH_IRQ_INT8 (8 + EMMA2RH_IRQ_BASE)
+#define EMMA2RH_IRQ_INT9 (9 + EMMA2RH_IRQ_BASE)
+#define EMMA2RH_IRQ_INT10 (10 + EMMA2RH_IRQ_BASE)
+#define EMMA2RH_IRQ_INT11 (11 + EMMA2RH_IRQ_BASE)
+#define EMMA2RH_IRQ_INT12 (12 + EMMA2RH_IRQ_BASE)
+#define EMMA2RH_IRQ_INT13 (13 + EMMA2RH_IRQ_BASE)
+#define EMMA2RH_IRQ_INT14 (14 + EMMA2RH_IRQ_BASE)
+#define EMMA2RH_IRQ_INT15 (15 + EMMA2RH_IRQ_BASE)
+#define EMMA2RH_IRQ_INT16 (16 + EMMA2RH_IRQ_BASE)
+#define EMMA2RH_IRQ_INT17 (17 + EMMA2RH_IRQ_BASE)
+#define EMMA2RH_IRQ_INT18 (18 + EMMA2RH_IRQ_BASE)
+#define EMMA2RH_IRQ_INT19 (19 + EMMA2RH_IRQ_BASE)
+#define EMMA2RH_IRQ_INT20 (20 + EMMA2RH_IRQ_BASE)
+#define EMMA2RH_IRQ_INT21 (21 + EMMA2RH_IRQ_BASE)
+#define EMMA2RH_IRQ_INT22 (22 + EMMA2RH_IRQ_BASE)
+#define EMMA2RH_IRQ_INT23 (23 + EMMA2RH_IRQ_BASE)
+#define EMMA2RH_IRQ_INT24 (24 + EMMA2RH_IRQ_BASE)
+#define EMMA2RH_IRQ_INT25 (25 + EMMA2RH_IRQ_BASE)
+#define EMMA2RH_IRQ_INT26 (26 + EMMA2RH_IRQ_BASE)
+#define EMMA2RH_IRQ_INT27 (27 + EMMA2RH_IRQ_BASE)
+#define EMMA2RH_IRQ_INT28 (28 + EMMA2RH_IRQ_BASE)
+#define EMMA2RH_IRQ_INT29 (29 + EMMA2RH_IRQ_BASE)
+#define EMMA2RH_IRQ_INT30 (30 + EMMA2RH_IRQ_BASE)
+#define EMMA2RH_IRQ_INT31 (31 + EMMA2RH_IRQ_BASE)
+#define EMMA2RH_IRQ_INT32 (32 + EMMA2RH_IRQ_BASE)
+#define EMMA2RH_IRQ_INT33 (33 + EMMA2RH_IRQ_BASE)
+#define EMMA2RH_IRQ_INT34 (34 + EMMA2RH_IRQ_BASE)
+#define EMMA2RH_IRQ_INT35 (35 + EMMA2RH_IRQ_BASE)
+#define EMMA2RH_IRQ_INT36 (36 + EMMA2RH_IRQ_BASE)
+#define EMMA2RH_IRQ_INT37 (37 + EMMA2RH_IRQ_BASE)
+#define EMMA2RH_IRQ_INT38 (38 + EMMA2RH_IRQ_BASE)
+#define EMMA2RH_IRQ_INT39 (39 + EMMA2RH_IRQ_BASE)
+#define EMMA2RH_IRQ_INT40 (40 + EMMA2RH_IRQ_BASE)
+#define EMMA2RH_IRQ_INT41 (41 + EMMA2RH_IRQ_BASE)
+#define EMMA2RH_IRQ_INT42 (42 + EMMA2RH_IRQ_BASE)
+#define EMMA2RH_IRQ_INT43 (43 + EMMA2RH_IRQ_BASE)
+#define EMMA2RH_IRQ_INT44 (44 + EMMA2RH_IRQ_BASE)
+#define EMMA2RH_IRQ_INT45 (45 + EMMA2RH_IRQ_BASE)
+#define EMMA2RH_IRQ_INT46 (46 + EMMA2RH_IRQ_BASE)
+#define EMMA2RH_IRQ_INT47 (47 + EMMA2RH_IRQ_BASE)
+#define EMMA2RH_IRQ_INT48 (48 + EMMA2RH_IRQ_BASE)
+#define EMMA2RH_IRQ_INT49 (49 + EMMA2RH_IRQ_BASE)
+#define EMMA2RH_IRQ_INT50 (50 + EMMA2RH_IRQ_BASE)
+#define EMMA2RH_IRQ_INT51 (51 + EMMA2RH_IRQ_BASE)
+#define EMMA2RH_IRQ_INT52 (52 + EMMA2RH_IRQ_BASE)
+#define EMMA2RH_IRQ_INT53 (53 + EMMA2RH_IRQ_BASE)
+#define EMMA2RH_IRQ_INT54 (54 + EMMA2RH_IRQ_BASE)
+#define EMMA2RH_IRQ_INT55 (55 + EMMA2RH_IRQ_BASE)
+#define EMMA2RH_IRQ_INT56 (56 + EMMA2RH_IRQ_BASE)
+#define EMMA2RH_IRQ_INT57 (57 + EMMA2RH_IRQ_BASE)
+#define EMMA2RH_IRQ_INT58 (58 + EMMA2RH_IRQ_BASE)
+#define EMMA2RH_IRQ_INT59 (59 + EMMA2RH_IRQ_BASE)
+#define EMMA2RH_IRQ_INT60 (60 + EMMA2RH_IRQ_BASE)
+#define EMMA2RH_IRQ_INT61 (61 + EMMA2RH_IRQ_BASE)
+#define EMMA2RH_IRQ_INT62 (62 + EMMA2RH_IRQ_BASE)
+#define EMMA2RH_IRQ_INT63 (63 + EMMA2RH_IRQ_BASE)
+
+#define EMMA2RH_IRQ_PFUR0 EMMA2RH_IRQ_INT49
+#define EMMA2RH_IRQ_PFUR1 EMMA2RH_IRQ_INT50
+#define EMMA2RH_IRQ_PFUR2 EMMA2RH_IRQ_INT51
+#define EMMA2RH_IRQ_PIIC0 EMMA2RH_IRQ_INT56
+#define EMMA2RH_IRQ_PIIC1 EMMA2RH_IRQ_INT57
+#define EMMA2RH_IRQ_PIIC2 EMMA2RH_IRQ_INT58
+
+/*
+ * EMMA2RH Register Access
+ */
+
+#define EMMA2RH_BASE (0xa0000000)
+
+#ifndef __ASSEMBLY__
+static inline void emma2rh_sync(void)
+{
+ volatile u32 *p = (volatile u32 *)0xbfc00000;
+ (void)(*p);
+}
+
+static inline void emma2rh_out32(u32 offset, u32 val)
+{
+ *(volatile u32 *)(EMMA2RH_BASE | offset) = val;
+ emma2rh_sync();
+}
+
+static inline u32 emma2rh_in32(u32 offset)
+{
+ u32 val = *(volatile u32 *)(EMMA2RH_BASE | offset);
+ emma2rh_sync();
+ return val;
+}
+
+static inline void emma2rh_out16(u32 offset, u16 val)
+{
+ *(volatile u16 *)(EMMA2RH_BASE | offset) = val;
+ emma2rh_sync();
+}
+
+static inline u16 emma2rh_in16(u32 offset)
+{
+ u16 val = *(volatile u16 *)(EMMA2RH_BASE | offset);
+ emma2rh_sync();
+ return val;
+}
+
+static inline void emma2rh_out8(u32 offset, u8 val)
+{
+ *(volatile u8 *)(EMMA2RH_BASE | offset) = val;
+ emma2rh_sync();
+}
+
+static inline u8 emma2rh_in8(u32 offset)
+{
+ u8 val = *(volatile u8 *)(EMMA2RH_BASE | offset);
+ emma2rh_sync();
+ return val;
+}
+#endif
+
+/**
+ * IIC registers map
+ **/
+
+/*---------------------------------------------------------------------------*/
+/* CNT - Control register (00H R/W) */
+/*---------------------------------------------------------------------------*/
+#define SPT 0x00000001
+#define STT 0x00000002
+#define ACKE 0x00000004
+#define WTIM 0x00000008
+#define SPIE 0x00000010
+#define WREL 0x00000020
+#define LREL 0x00000040
+#define IICE 0x00000080
+#define CNT_RESERVED 0x000000ff /* reserved bit 0 */
+
+#define I2C_EMMA_START (IICE | STT)
+#define I2C_EMMA_STOP (IICE | SPT)
+#define I2C_EMMA_REPSTART I2C_EMMA_START
+
+/*---------------------------------------------------------------------------*/
+/* STA - Status register (10H Read) */
+/*---------------------------------------------------------------------------*/
+#define MSTS 0x00000080
+#define ALD 0x00000040
+#define EXC 0x00000020
+#define COI 0x00000010
+#define TRC 0x00000008
+#define ACKD 0x00000004
+#define STD 0x00000002
+#define SPD 0x00000001
+
+/*---------------------------------------------------------------------------*/
+/* CSEL - Clock select register (20H R/W) */
+/*---------------------------------------------------------------------------*/
+#define FCL 0x00000080
+#define ND50 0x00000040
+#define CLD 0x00000020
+#define DAD 0x00000010
+#define SMC 0x00000008
+#define DFC 0x00000004
+#define CL 0x00000003
+#define CSEL_RESERVED 0x000000ff /* reserved bit 0 */
+
+#define FAST397 0x0000008b
+#define FAST297 0x0000008a
+#define FAST347 0x0000000b
+#define FAST260 0x0000000a
+#define FAST130 0x00000008
+#define STANDARD108 0x00000083
+#define STANDARD83 0x00000082
+#define STANDARD95 0x00000003
+#define STANDARD73 0x00000002
+#define STANDARD36 0x00000001
+#define STANDARD71 0x00000000
+
+/*---------------------------------------------------------------------------*/
+/* SVA - Slave address register (30H R/W) */
+/*---------------------------------------------------------------------------*/
+#define SVA 0x000000fe
+
+/*---------------------------------------------------------------------------*/
+/* SHR - Shift register (40H R/W) */
+/*---------------------------------------------------------------------------*/
+#define SR 0x000000ff
+
+/*---------------------------------------------------------------------------*/
+/* INT - Interrupt register (50H R/W) */
+/* INTM - Interrupt mask register (60H R/W) */
+/*---------------------------------------------------------------------------*/
+#define INTE0 0x00000001
+
+/***********************************************************************
+ * I2C registers
+ ***********************************************************************
+ */
+#define I2C_EMMA_CNT 0x00
+#define I2C_EMMA_STA 0x10
+#define I2C_EMMA_CSEL 0x20
+#define I2C_EMMA_SVA 0x30
+#define I2C_EMMA_SHR 0x40
+#define I2C_EMMA_INT 0x50
+#define I2C_EMMA_INTM 0x60
+
+/*
+ * include the board dependent part
+ */
+#if defined(CONFIG_MARKEINS)
+#include <asm/emma2rh/markeins.h>
+#else
+#error "Unknown EMMA2RH board!"
+#endif
+
+#endif /* __ASM_EMMA2RH_EMMA2RH_H */
Index: linux-2.6.10/include/asm-mips/emma2rh/hardware.h
===================================================================
--- /dev/null
+++ linux-2.6.10/include/asm-mips/emma2rh/hardware.h
@@ -0,0 +1,29 @@
+
+#define FLASH_WINDOW_ADDR 0x1e000000
+#define FLASH_WINDOW_SIZE 0x02000000
+#endif /* CONFIG_MARKEINS */
+
+/* -------------------------------------------------------------------- */
+/* i2c-algo-emma2rh.h: NEC EMMA2RH global defines */
+/* -------------------------------------------------------------------- */
+/*
+ Copyright (C) NEC Electronics Corporation 2005-2006
+
+ This program is free software; you can redistribute it and/or modify
+ it under the terms of the GNU General Public License as published by
+ the Free Software Foundation; either version 2 of the License, or
+ (at your option) any later version.
+
+ This program is distributed in the hope that it will be useful,
+ but WITHOUT ANY WARRANTY; without even the implied warranty of
+ MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ GNU General Public License for more details.
+
+ You should have received a copy of the GNU General Public License
+ along with this program; if not, write to the Free Software
+ Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA*/
+/* -------------------------------------------------------------------- */
+
+#ifndef I2C_EMMA2RH_H
+#define I2C_EMMA2RH_H
+#endif /* I2C_EMMA2RH_H */
Index: linux-2.6.10/include/asm-mips/emma2rh/markeins.h
===================================================================
--- /dev/null
+++ linux-2.6.10/include/asm-mips/emma2rh/markeins.h
@@ -0,0 +1,80 @@
+/*
+ * include/asm-mips/emma2rh/markeins.h
+ * This file is EMMA2RH board depended header.
+ *
+ * Copyright (C) NEC Electronics Corporation 2005-2006
+ *
+ * This file based on include/asm-mips/ddb5xxx/ddb5xxx.h
+ * Copyright 2001 MontaVista Software Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
+ */
+
+#ifndef MARKEINS_H
+#define MARKEINS_H
+
+#define NUM_EMMA2RH_IRQ_SW 32
+#define NUM_EMMA2RH_IRQ_GPIO 32
+
+#define EMMA2RH_SW_CASCADE (EMMA2RH_IRQ_INT7 - EMMA2RH_IRQ_INT0)
+#define EMMA2RH_GPIO_CASCADE (EMMA2RH_IRQ_INT46 - EMMA2RH_IRQ_INT0)
+
+#define EMMA2RH_SW_IRQ_BASE (EMMA2RH_IRQ_BASE + NUM_EMMA2RH_IRQ)
+#define EMMA2RH_GPIO_IRQ_BASE (EMMA2RH_SW_IRQ_BASE + NUM_EMMA2RH_IRQ_SW)
+#define CPU_IRQ_BASE (EMMA2RH_GPIO_IRQ_BASE + NUM_EMMA2RH_IRQ_GPIO)
+
+#define EMMA2RH_SW_IRQ_INT0 (0+EMMA2RH_SW_IRQ_BASE)
+#define EMMA2RH_SW_IRQ_INT1 (1+EMMA2RH_SW_IRQ_BASE)
+#define EMMA2RH_SW_IRQ_INT2 (2+EMMA2RH_SW_IRQ_BASE)
+#define EMMA2RH_SW_IRQ_INT3 (3+EMMA2RH_SW_IRQ_BASE)
+#define EMMA2RH_SW_IRQ_INT4 (4+EMMA2RH_SW_IRQ_BASE)
+#define EMMA2RH_SW_IRQ_INT5 (5+EMMA2RH_SW_IRQ_BASE)
+#define EMMA2RH_SW_IRQ_INT6 (6+EMMA2RH_SW_IRQ_BASE)
+#define EMMA2RH_SW_IRQ_INT7 (7+EMMA2RH_SW_IRQ_BASE)
+#define EMMA2RH_SW_IRQ_INT8 (8+EMMA2RH_SW_IRQ_BASE)
+#define EMMA2RH_SW_IRQ_INT9 (9+EMMA2RH_SW_IRQ_BASE)
+#define EMMA2RH_SW_IRQ_INT10 (10+EMMA2RH_SW_IRQ_BASE)
+#define EMMA2RH_SW_IRQ_INT11 (11+EMMA2RH_SW_IRQ_BASE)
+#define EMMA2RH_SW_IRQ_INT12 (12+EMMA2RH_SW_IRQ_BASE)
+#define EMMA2RH_SW_IRQ_INT13 (13+EMMA2RH_SW_IRQ_BASE)
+#define EMMA2RH_SW_IRQ_INT14 (14+EMMA2RH_SW_IRQ_BASE)
+#define EMMA2RH_SW_IRQ_INT15 (15+EMMA2RH_SW_IRQ_BASE)
+#define EMMA2RH_SW_IRQ_INT16 (16+EMMA2RH_SW_IRQ_BASE)
+#define EMMA2RH_SW_IRQ_INT17 (17+EMMA2RH_SW_IRQ_BASE)
+#define EMMA2RH_SW_IRQ_INT18 (18+EMMA2RH_SW_IRQ_BASE)
+#define EMMA2RH_SW_IRQ_INT19 (19+EMMA2RH_SW_IRQ_BASE)
+#define EMMA2RH_SW_IRQ_INT20 (20+EMMA2RH_SW_IRQ_BASE)
+#define EMMA2RH_SW_IRQ_INT21 (21+EMMA2RH_SW_IRQ_BASE)
+#define EMMA2RH_SW_IRQ_INT22 (22+EMMA2RH_SW_IRQ_BASE)
+#define EMMA2RH_SW_IRQ_INT23 (23+EMMA2RH_SW_IRQ_BASE)
+#define EMMA2RH_SW_IRQ_INT24 (24+EMMA2RH_SW_IRQ_BASE)
+#define EMMA2RH_SW_IRQ_INT25 (25+EMMA2RH_SW_IRQ_BASE)
+#define EMMA2RH_SW_IRQ_INT26 (26+EMMA2RH_SW_IRQ_BASE)
+#define EMMA2RH_SW_IRQ_INT27 (27+EMMA2RH_SW_IRQ_BASE)
+#define EMMA2RH_SW_IRQ_INT28 (28+EMMA2RH_SW_IRQ_BASE)
+#define EMMA2RH_SW_IRQ_INT29 (29+EMMA2RH_SW_IRQ_BASE)
+#define EMMA2RH_SW_IRQ_INT30 (30+EMMA2RH_SW_IRQ_BASE)
+#define EMMA2RH_SW_IRQ_INT31 (31+EMMA2RH_SW_IRQ_BASE)
+
+#define MARKEINS_PCI_IRQ_INTA EMMA2RH_GPIO_IRQ_BASE+15
+#define MARKEINS_PCI_IRQ_INTB EMMA2RH_GPIO_IRQ_BASE+16
+#define MARKEINS_PCI_IRQ_INTC EMMA2RH_GPIO_IRQ_BASE+17
+#define MARKEINS_PCI_IRQ_INTD EMMA2RH_GPIO_IRQ_BASE+18
+
+/* flash */
+#define FLASH_WINDOW_ADDR 0x1e000000
+#define FLASH_WINDOW_SIZE 0x02000000
+
+#endif /* CONFIG_MARKEINS */
Index: linux-2.6.10/include/asm-mips/mach-emma2rh/irq.h
===================================================================
--- /dev/null
+++ linux-2.6.10/include/asm-mips/mach-emma2rh/irq.h
@@ -0,0 +1,13 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License. See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 2003 by Ralf Baechle
+ */
+#ifndef __ASM_MACH_EMMA2RH_IRQ_H
+#define __ASM_MACH_EMMA2RH_IRQ_H
+
+#define NR_IRQS 256
+
+#endif /* __ASM_MACH_EMMA2RH_IRQ_H */
Index: linux-2.6.10/arch/mips/emma2rh/markeins/platform.c
===================================================================
--- /dev/null
+++ linux-2.6.10/arch/mips/emma2rh/markeins/platform.c
@@ -0,0 +1,135 @@
+/*
+ * arch/mips/emma2rh/markeins/platofrm.c
+ * This file sets up platform devices for EMMA2RH Mark-eins.
+ *
+ * Copyright(C) MontaVista Software Inc, 2006
+ *
+ * Author: dmitry pervushin <dpervushin@xxxxxxxxxxxxx>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
+ */
+#include <linux/config.h>
+#include <linux/init.h>
+#include <linux/kernel.h>
+#include <linux/types.h>
+#include <linux/ioport.h>
+#include <linux/serial_8250.h>
+
+#include <asm/cpu.h>
+#include <asm/bootinfo.h>
+#include <asm/addrspace.h>
+#include <asm/time.h>
+#include <asm/bcache.h>
+#include <asm/irq.h>
+#include <asm/reboot.h>
+#include <asm/gdb-stub.h>
+#include <asm/traps.h>
+#include <asm/debug.h>
+
+#include <asm/emma2rh/emma2rh.h>
+
+
+#define I2C_EMMA2RH "emma2rh-iic" /* must be in sync with IIC driver */
+
+static struct resource i2c_emma_resources_0[] = {
+ { NULL, EMMA2RH_IRQ_PIIC0, EMMA2RH_IRQ_PIIC0, IORESOURCE_IRQ },
+ { NULL, KSEG1ADDR(EMMA2RH_PIIC0_BASE), KSEG1ADDR(EMMA2RH_PIIC0_BASE + 0x1000), 0 },
+};
+
+struct resource i2c_emma_resources_1[] = {
+ { NULL, EMMA2RH_IRQ_PIIC1, EMMA2RH_IRQ_PIIC1, IORESOURCE_IRQ },
+ { NULL, KSEG1ADDR(EMMA2RH_PIIC1_BASE), KSEG1ADDR(EMMA2RH_PIIC1_BASE + 0x1000), 0 },
+};
+
+struct resource i2c_emma_resources_2[] = {
+ { NULL, EMMA2RH_IRQ_PIIC2, EMMA2RH_IRQ_PIIC2, IORESOURCE_IRQ },
+ { NULL, KSEG1ADDR(EMMA2RH_PIIC2_BASE), KSEG1ADDR(EMMA2RH_PIIC2_BASE + 0x1000), 0 },
+};
+
+struct platform_device i2c_emma_devices[] = {
+ [0] = {
+ .name = I2C_EMMA2RH,
+ .id = 0,
+ .resource = i2c_emma_resources_0,
+ .num_resources = ARRAY_SIZE(i2c_emma_resources_0),
+ },
+ [1] = {
+ .name = I2C_EMMA2RH,
+ .id = 1,
+ .resource = i2c_emma_resources_1,
+ .num_resources = ARRAY_SIZE(i2c_emma_resources_1),
+ },
+ [2] = {
+ .name = I2C_EMMA2RH,
+ .id = 2,
+ .resource = i2c_emma_resources_2,
+ .num_resources = ARRAY_SIZE(i2c_emma_resources_2),
+ },
+};
+
+#define EMMA2RH_SERIAL_CLOCK 18544000
+#define EMMA2RH_SERIAL_FLAGS UPF_BOOT_AUTOCONF | UPF_SKIP_TEST | UPF_AUTO_IRQ
+
+static struct plat_serial8250_port platform_serial_ports[] = {
+ [0] = {
+ .membase = (void __iomem*)KSEG1ADDR(EMMA2RH_PFUR0_BASE + 3),
+ .irq = EMMA2RH_IRQ_PFUR0,
+ .uartclk = EMMA2RH_SERIAL_CLOCK,
+ .regshift = 4,
+ .iotype = UPIO_MEM,
+ .flags = EMMA2RH_SERIAL_FLAGS,
+ },
+ [1] = {
+ .membase = (void __iomem*)KSEG1ADDR(EMMA2RH_PFUR1_BASE + 3),
+ .irq = EMMA2RH_IRQ_PFUR1,
+ .uartclk = EMMA2RH_SERIAL_CLOCK,
+ .regshift = 4,
+ .iotype = UPIO_MEM,
+ .flags = EMMA2RH_SERIAL_FLAGS,
+ },
+ [2] = {
+ .membase = (void __iomem*)KSEG1ADDR(EMMA2RH_PFUR2_BASE + 3),
+ .irq = EMMA2RH_IRQ_PFUR2,
+ .uartclk = EMMA2RH_SERIAL_CLOCK,
+ .regshift = 4,
+ .iotype = UPIO_MEM,
+ .flags = EMMA2RH_SERIAL_FLAGS,
+ },
+ [3] = {
+ .flags = 0,
+ },
+};
+
+static struct platform_device serial_emma = {
+ .name = "serial8250",
+ .dev = {
+ .platform_data = &platform_serial_ports,
+ },
+};
+
+static struct platform_device *devices[] = {
+ &i2c_emma_devices[0],
+ &i2c_emma_devices[1],
+ &i2c_emma_devices[2],
+ &serial_emma,
+};
+
+static int __init platform_devices_setup(void)
+{
+ return platform_add_devices(devices, ARRAY_SIZE(devices));
+}
+
+arch_initcall(platform_devices_setup);
+
--
cheers, dmitry pervushin
