hi thomas! i think the problem is that in arch/mips/au1000/mtx-1/board_setup.c the power switch for USB is turned on if CONFIG_USB_OHCI is defined. this seems to have changed to CONFIG_USB_OHCI_HCD. bruno On Wednesday 15 June 2005 15:46, you wrote: > Hi there ... > > My name is Thomas I'm trying to use an USB-headset on a meshcube, a MIPS > based embedded device (http://meshcube.org/meshwiki/). If I plug in the > headset while running 2.4.27 a led on the headset turns on. If I do the > same with 2.6.12-rc6 (latest MIPS CVS) nothing happens. I also tried an > optical USB-mouse with the same result. All these tests are done with > Debian GNU/Linux Sarge 3.1 on NFS-root. > > My kernelconfig is: > $ sed '/^#/d;/USB/!d' .config > CONFIG_SND_USB_AUDIO=m > CONFIG_USB=y > CONFIG_USB_DEBUG=y > CONFIG_USB_DEVICEFS=y > CONFIG_USB_ARCH_HAS_HCD=y > CONFIG_USB_ARCH_HAS_OHCI=y > CONFIG_USB_EHCI_HCD=m > CONFIG_USB_OHCI_HCD=y > CONFIG_USB_HID=y > CONFIG_USB_HIDINPUT=y > > kernel boot messages are: > usbcore: registered new driver usbfs > usbcore: registered new driver hub > [...] > au1xxx-ohci au1xxx-ohci.0: Au1xxx OHCI > au1xxx-ohci au1xxx-ohci.0: new USB bus registered, assigned bus number 1 > au1xxx-ohci au1xxx-ohci.0: irq 26, io mem 0x10100000 > usb usb1: Product: Au1xxx OHCI > usb usb1: Manufacturer: Linux 2.6.12-rc6 ohci_hcd > usb usb1: SerialNumber: Au1xxx > hub 1-0:1.0: USB hub found > hub 1-0:1.0: 2 ports detected > USB Universal Host Controller Interface driver v2.2 > sl811: driver sl811-hcd, 19 May 2005 > > FYI 2.4.27 messages: > usb.c: registered new driver usbdevfs > usb.c: registered new driver hub > host/usb-ohci.c: USB OHCI at membase 0xb0100000, IRQ 26 > host/usb-ohci.c: usb-builtin, non-PCI OHCI > usb.c: new USB bus registered, assigned bus number 1 > hub.c: USB hub found > hub.c: 2 ports detected > > hotplug (initscripts) report: > Starting hotplug subsystem: > pci > pci [success] > usb > usb [success] > isapnp > isapnp [success] > ide > ide [success] > input > input [success] > scsi > scsi [success] > done. > > the proc-filesystem tells: > $ cat /proc/bus/usb/devices > T: Bus=01 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=12 MxCh= 2 > B: Alloc= 0/900 us ( 0%), #Int= 0, #Iso= 0 > D: Ver= 1.10 Cls=09(hub ) Sub=00 Prot=00 MxPS= 8 #Cfgs= 1 > P: Vendor=0000 ProdID=0000 Rev= 2.06 > S: Manufacturer=Linux 2.6.11 ohci_hcd > S: Product=Au1xxx OHCI > S: SerialNumber=au1xxx > C:* #Ifs= 1 Cfg#= 1 Atr=c0 MxPwr= 0mA > I: If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub > E: Ad=81(I) Atr=03(Int.) MxPS= 2 Ivl=255ms > > As far as I can see USB drivers are working correctly, hardware is > detected but the USB is not working. Any hints? > > TIA > Thomas
Attachment:
pgpvWH18HctiB.pgp
Description: PGP signature
