Hi all, I'm using scratchbox and meamo to build my root filesystem. I fallow the steps shown in the HOWTO: Using flasher and the reference root filesystem. The link is: http://www.maemo.org/platform/docs/howtos/howto_use_flasher_rootfs.html Finally, I got the jffs2 image of my root filesystem and download it to my board OSK5912 successfully. But I meet the following error messages when boot the kernel: ............................................................................ Sending DHCP requests ., OK IP-Config: Got DHCP answer from 192.168.4.1, my address is 192.168.4.190 IP-Config: Complete: device=eth0, addr=192.168.4.190, mask=255.255.255.0, gw=192.168.4.1, host=192.168.4.190, domain=omap1_eth1, nis-domain=(none), bootserver=192.168.4.1, rootserver=192.168.4.1, rootpath= Node at 0x0062e3b8 with length 0x80001044 would run over the end of the erase block Perhaps the file system was created with the wrong erase size? jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x0062e3bc: 0x1044 instead jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x0062e3c0: 0x586d instead jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x0062e3c4: 0x030c instead jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x0062e3c8: 0x001a instead jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x0062e3cc: 0x81a4 instead jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x0062e3d4: 0xacc3 instead jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x0062e3d8: 0x2317 instead jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x0062e3dc: 0x2317 instead jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x0062e3e0: 0x2317 instead jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x0062e3e4: 0x9000 instead Further such events for this erase block will not be printed Node at 0x00630138 with length 0x80000777 would run over the end of the erase block Perhaps the file system was created with the wrong erase size? Node at 0x006311f8 with length 0x80000f3d would run over the end of the erase block Perhaps the file system was created with the wrong erase size? Node at 0x00632138 with length 0x80000fe5 would run over the end of the erase block Perhaps the file system was created with the wrong erase size? Node at 0x00635138 with length 0x8000103f would run over the end of the erase block Perhaps the file system was created with the wrong erase size? Node at 0x00636178 with length 0x80000045 would run over the end of the erase block Perhaps the file system was created with the wrong erase size? ............................................................................ It seems the filesystem can work as NFS, but not stable. It can work once in three times approximately, and in the other times it can't go further more when the following messages shown on the console: ............................................................................ Looking up port of RPC 100003/2 on 192.168.0.11 Looking up port of RPC 100005/1 on 192.168.0.11 VFS: Mounted root (nfs filesystem). Freeing init memory: 120K ............................................................................ My board is OSK5912 and the kernel is omap-linux-2.6.14. I have had these problems for quite a while, but have never been able to identify the cause. Dos anyone have experience in it? Any help will be appreciated. Thank in advance. Best regards. xuxian
