Hi Jean,
I have followed your advices and updated the D201GLY2. Here it is:
# libsensors configuration file
# -----------------------------
#
# Configuration file for Intel D201GLY2 motherboard
# Hardware monitor subsystem controlled by Winbond W83627DHG-B I/O
controller.
# Created using information from BIOS and board documentation.
chip "w83627dhg-*"
label in1 "+12.0V"
label in4 "+5V"
label in6 "+1.5V"
# in5 is obvioulsy unconnected, so ignore it
ignore in5
compute in1 @*(55/8),@/(55/8)
compute in4 @*(1+18/10),@/(1+18/10)
set in1_min 12.0 * 0.95
set in1_max 12.0 * 1.05
set in4_min 5.0 * 0.90
set in4_max 5.0 * 1.10
set in6_min 1.5 * 0.90
set in6_max 1.5 * 1.10
label fan1 "Chassis fan"
label fan2 "CPU fan"
# By default the D201GLY2 has a passive heatsink. If the optional active
# heatsink is present, then one of the following lines is to be commented
out
# (very likely fan2, though not tried).
ignore fan2
ignore fan3
ignore fan4
label temp1 "Sys temp"
label temp2 "CPU temp"
ignore temp3
ignore cpu0_vid
ignore intrusion0
And here is the output from sensors:
eric@tangha ~/srv_conf % sensors
coretemp-isa-0000
Adapter: ISA adapter
Core 0: +55.0°C (high = +100.0°C, crit = +100.0°C)
w83627dhg-isa-0290
Adapter: ISA adapter
Vcore: +1.34 V (min = +0.00 V, max = +1.74 V)
+12.0V: +11.82 V (min = +11.38 V, max = +12.60 V)
AVCC: +3.25 V (min = +2.98 V, max = +3.63 V)
+3.3V: +3.25 V (min = +2.98 V, max = +3.63 V)
+5V: +5.06 V (min = +4.50 V, max = +5.51 V)
+1.5V: +1.56 V (min = +1.35 V, max = +1.65 V)
3VSB: +3.25 V (min = +2.98 V, max = +3.63 V)
Vbat: +3.09 V (min = +2.70 V, max = +3.63 V)
Chassis fan: 2721 RPM (min = 777 RPM, div = 8)
Sys temp: +43.0°C (high = +43.0°C, hyst = +14.0°C) ALARM sensor =
thermistor
CPU temp: +49.5°C (high = +110.0°C, hyst = +75.0°C) sensor = CPU diode
2014-07-25 20:05 GMT+02:00 Jean Delvare <jdelvare@xxxxxxx>:
> On Fri, 25 Jul 2014 18:44:13 +0200, Éric Le Bras wrote:
> > 2014-07-25 17:45 GMT+02:00 Jean Delvare <jdelvare@xxxxxxx>:
> > > On Fri, 25 Jul 2014 15:55:06 +0200, Éric Le Bras wrote:
> > > > Temp3 has a weird behaviour. It lowers when the CPU load increases. I
> > > > enclosed a graph generated with sensord. The curve for temp3 has an
> > > > "inversed" profile, compared to other temps.
> > >
> > > That does not mean it's wrong. You should draw the fan speed together
> > > with the temperatures. Higher CPU temperature will typically result in
> > > a faster spinning fan, which in turn can lower the temperature of
> > > other parts of the system. This is even more likely for a system
> > > without a CPU fan where the CPU cooling is achieved by the case fan.
> > >
> > > 20.5°C could well be the ambient temperature inside the case, if case
> > > cooling is very good and the room temperature is cool too.
> >
> > Not sure. First the fan is not regulated, so it spins at constant speed.
> > Next, I live in southern France, and the room has no AC, so the room
> > temperature is approx. 25°C today.
>
> I'm there (Mérignac) and I agree it's hot today ;-) So my theory doesn't
> hold. Feel free to just ignore temp3 then.
>
> > (...)
> > For the +12V, I had only one value found on the web (12.084), and I
> > observed 2 differents values on the BIOS on my own PC (11.935 and
> 11.990).
> >
> > The 12V was alterning between the 2 values 11.935 and 11.990, and only
> one
> > of the 3 possibles sensors (in1, in4 and in5) was alterning at the same
> > time : in1 (1.736 and 1.744).
> >
> > The site says the atomic measure for the W83627DHG is 8mv. So I tried
> with
> > a divisor of 8, and found that the ratio 55/8 was ok. It gave exactly the
> > temperatures displayed by the BIOS when applied to in1.
>
> s/temperatures/voltages/ ;-)
>
> The method used was not the best but your results seem to be correct
> nevertheless, in1 must be +12V.
>
> --
> Jean Delvare
> SUSE L3 Support
>
_______________________________________________
lm-sensors mailing list
lm-sensors@xxxxxxxxxxxxxx
http://lists.lm-sensors.org/mailman/listinfo/lm-sensors
