I wish to share this configuration if Jean or somebody else could verify what I have done so far and add this to the wiki. Here's the default sensors output (only the unconfigured inputs are shown): $ sensors -u in1: in1_input: 1.856 in1_min: 2.040 in1_max: 1.712 in1_alarm: 1.000 in4: in4_input: 1.648 in4_min: 1.520 in4_max: 1.680 in4_alarm: 0.000 in5: in5_input: 1.632 in5_min: 1.488 in5_max: 1.648 in5_alarm: 0.000 in6: in6_input: 0.184 in6_min: 1.976 in6_max: 1.520 in6_alarm: 1.000 in9: in9_input: 0.184 in9_min: 1.248 in9_max: 0.872 in9_alarm: 1.000 For the +12V scaling: +12V BIOS samples: 12.196, 12.249, 12.302 12.249 - 12.196 = 0.053 12.302 - 12.249 = 0.053 12.249 / (1+56/10) = 1.855909091 1.855909091 is close enough to in1 (1.856) To verify the scaling factor: 231 * 0.008 * (1+56/10) = 12.1968 232 * 0.008 * (1+56/10) = 12.2496 233 * 0.008 * (1+56/10) = 12.3024 and it almost matches exactly to each BIOS samples. The compute statement for +12V scaling is: compute in1 @*(1+56/10), @/(1+56/10) For the +5V scaling: +5V BIOS samples: 5.094, 5.145, 5.171, 5.196 5.145 - 5.094 = 0.051 5.171 - 5.145 = 0.026 5.196 - 5.171 = 0.025 (5.196 - 5.094) / (2 + 1 + 1) = 0.0255 5.196 / (255/80) = 1.630117647 1.614117647 is close enough to in5 (1.632) But when I tried to verify the scaling factor: 202 * 0.008 * (255/80) = 5.151 203 * 0.008 * (255/80) = 5.1765 204 * 0.008 * (255/80) = 5.202 So I'm not so sure if this is acceptable. If I made a mistake from my above calculations please let me know. The compute statement for +5V scaling is: compute in5 @*(255/80), @/(255/80) And this is the entire configuration: ### Sensors configuration for Asus P5PE-VM motherboard ### 2014-02-28, ianp <snailbox88-dev -at- yahoo -dot- com> ### Comments are welcome. chip "w83627ehf-*" ### Voltages label in1 "+12V" ignore in4 # ignored (not used?) label in5 "+5V" ignore in6 # ignore these ignore in9 # as well (not used) ignore cpu0_vid # Always at 0 in my case, so ignore it ### Scale +5V and +12V. compute in5 @*(255/8), @/(255/80) compute in1 @*(1+56/10), @/(1+56/10) ### Set in0 according to CPU nominal voltage. set in0_min 1.2000 set in0_max 1.3375 set in5_min 5 * 0.95 set in5_max 5 * 1.05 set in1_min 12 * 0.95 set in1_max 12 * 1.05 ### Temperatures # temp3 is unidentified label temp1 "M/B Temp" label temp2 "CPU Temp" ### Set according to preference. set temp1_max 60 set temp1_max_hyst 55 set temp2_max 60 set temp2_max_hyst 55 ### Fans ### Ignore fan3 and fan5. There are ### only 2 fan connectors on this board. ### fan4 is missing. label fan1 "CHA Fan" label fan2 "CPU Fan" ignore fan3 ignore fan5 ### Set according to preference. set fan1_min 0 set fan2_min 900 _______________________________________________ lm-sensors mailing list lm-sensors@xxxxxxxxxxxxxx http://lists.lm-sensors.org/mailman/listinfo/lm-sensors
