Hi,
I'm trying to use my thermal sensor on my powerpc p3041 board.
I add CONFIG_SENSORS_ADT7410, CONFIG_HWMON, CONFIG_THERMAL and my
linux config (3.8.13)
I2c works:
# i2cdump 1 0x48
No size specified (using byte-data access)
WARNING! This program can confuse your I2C bus, cause data loss and worse!
I will probe file /dev/i2c-1, address 0x48, mode byte
Continue? [Y/n]
0 1 2 3 4 5 6 7 8 9 a b c d e f 0123456789abcdef
00: 0f f8 80 00 20 00 05 00 49 80 05 cb 00 00 00 00 ???. .?.I???....
10: 00 00 00 00 00 00 00 00 38 00 06 00 00 00 00 00 ........8.?.....
20: 0f f8 80 00 20 00 05 00 49 80 05 cb 00 00 00 00 ???. .?.I???....
30: 00 00 00 00 00 00 00 00 38 00 06 00 00 00 00 00 ........8.?.....
40: 00 00 80 00 20 00 05 00 49 80 05 cb 00 00 00 00 ..?. .?.I???....
50: 00 00 00 00 00 00 00 00 38 00 06 00 00 00 00 00 ........8.?.....
60: 00 00 80 00 20 00 05 00 49 80 05 cb 00 00 00 00 ..?. .?.I???....
70: 00 00 00 00 00 00 00 00 38 00 06 00 00 00 00 00 ........8.?.....
80: 00 00 80 00 20 00 05 00 49 80 05 cb 00 00 00 00 ..?. .?.I???....
90: 00 00 00 00 00 00 00 00 38 00 06 00 00 00 00 00 ........8.?.....
a0: 00 00 80 00 20 00 05 00 49 80 05 cb 00 00 00 00 ..?. .?.I???....
b0: 00 00 00 00 00 00 00 00 38 00 06 00 00 00 00 00 ........8.?.....
c0: 00 00 80 00 20 00 05 00 49 80 05 cb 00 00 00 00 ..?. .?.I???....
d0: 00 00 00 00 00 00 00 00 38 00 06 00 00 00 00 00 ........8.?.....
e0: 00 00 80 00 20 00 05 00 49 80 05 cb 00 00 00 00 ..?. .?.I???....
f0: 00 00 00 00 00 00 00 00 38 00 06 00 00 00 00 00 ........8.?.....
Probing for `Analog Devices ADT7410/ADT7420'... Success!
(confidence 3, driver `adt7410')
# sensors
No sensors found!
Make sure you loaded all the kernel drivers you need.
Try sensors-detect to find out which these are.
adt7410 is already built in the kernel....
Does anybody have an idea?
Thanks a lot
Ivan
_______________________________________________
lm-sensors mailing list
lm-sensors@xxxxxxxxxxxxxx
http://lists.lm-sensors.org/mailman/listinfo/lm-sensors
