I apologize - I did introduce a typo, it's the P85, not P58. :-[ On 2013-08-18 17:55, Nils Hammar wrote:
I have made a best effort to create a configuration file for the Gigabyte GA-P85-D3 motherboard. I can't guarantee that it's entirely correct since it is created through trial&error. I provide it in hope that it is useful for someone else.Below is the file content: --- # # Configuration for the Gigabyte GA-P85-D3 motherboard. # # Driver 'it87' at it8728-isa-0a30. # # This motherboard is for the fourth generation Intel Core processors # with Socket 1150. One important difference is that those processors # has internal voltage regulation, which means that some voltages # that were present on earlier motherboards are no longer there. # One such example is the Vtt voltage. # # chip "it8728-*" ####################################### # FANS # # The actual number of fans and their # # RPM limits depends on what the # # computer case is equipped with # # and your CPU fan, so you may # # want to update this section. # ####################################### label fan1 "CPU fan" set fan1_min 700 label fan2 "System fan 1" set fan2_min 300 label fan3 "System fan 2" set fan3_min 300 ignore fan4 # Remove the 'ignore' if fan is installed. label fan4 "System fan 3" set fan4_min 0 # Set to a valid value if fan is installed.ignore fan5 # Not present on motherboard, listed here since the chip supports it.label fan5 "System fan 4" set fan5_min 0 ###################################### # VOLTAGES # # These figures are from estimations # # based on values provided in BIOS. # # This means that some of them may # # be mixed up. # ###################################### label in0 "Vcore" set in0_min 0.05 set in0_max 1.025 compute in0 1.0*@,@/1.0 label in1 "+3.3V" set in1_min 3.135 # according to ATX 12V PSU design guide set in1_max 3.465 # compute in1 1.635*@,@/1.635 label in2 "+12V" set in2_min 11.40 # according to ATX 12V PSU design guide set in2_max 12.60 # compute in2 6.0*@,@/6.0 label in3 "+5V" set in3_min 4.750 # according to ATX 12V PSU design guide set in3_max 5.250 # compute in3 2.5*@,@/2.5 label in4 "Vaxg" set in4_min 0.80 set in4_max 1.00 compute in4 1.0*@,@/1.0 label in5 "Vrin" set in5_min 1.65 set in5_max 1.85 compute in5 1.0*@,@/1.0 label in6 "Vdram" set in6_min 1.45 # adjust these, 1.35 for LVDDR3 set in6_max 1.55 # 1.5V is recommended, 1.65 tops compute in6 1.0*@,@/1.0 label in7 "3VSB" set in7_min 3.14 set in7_max 3.47 compute in7 1.0*@,@/1.0 # CMOS Battery voltage. label in8 "Vbat" compute in8 1.0*@,@/1.0 ############################### # Temperatures # ############################### label temp1 "PCH temp" set temp1_min 10 set temp1_max 60 # ignore temp2 # Not sure if this sensor actually exists. # It's always reporting 25 degrees Celsius for me at the moment. label temp2 "MB temp" set temp2_min 0 set temp2_max 60 label temp3 "CPU temp" set temp3_min 10 set temp3_max 85 _______________________________________________ lm-sensors mailing list lm-sensors@xxxxxxxxxxxxxx http://lists.lm-sensors.org/mailman/listinfo/lm-sensors
_______________________________________________ lm-sensors mailing list lm-sensors@xxxxxxxxxxxxxx http://lists.lm-sensors.org/mailman/listinfo/lm-sensors
