GMT G762/763 fan speed PWM controller is connected directly to a fan
and performs closed-loop or open-loop control of the fan speed. Two
modes - PWM or DC - are supported by the chip. Introduced driver
provides various knobs to control the operations of the chip (via
sysfs interface). Specific characteristics of the system can be passed
either using board init code or via DT. Documentation for both the
driver and DT bindings are also provided.
Signed-off-by: Arnaud Ebalard <arno@xxxxxxxxxxxx>
---
Guenter, do not hesitate to tell me if changes associated with the
switch from a simple property DT for clock frequency to a fixed
clock require some additional work. History of changes is below.
Changes since v4:
Fixed issue reported by Simon (open-loop not working when set_cnt is 255)
replaced ref_clk property by a required reference to a clock in .dts
now use a fixed clock in DT instead of a simple property
Replace fan_pulses property in DT in favour of a sysfs attribute
s/pwm_freq/clk_freq/g and fixed associated comments
removed whole G762_VAL_TEST_BIT hack
merged all three patches into one
removed useless settings of data->valid to false
do not hide original return code in g762_one_prop_commit()
Removed unused defines
fixed various comments
fixed comment for get/set_pwm_enable() (still not supporting 0 for pwm1_enable)
fixed comment for get/set_pwm()
fixed reversed polarity setter logic
simplified do_set_pwm()
Changes since v3:
set is against current head of Linus tree
removed dev_err() calls when i2c_smbus_read/write_byte_data() fails
pwm1 sets SET_OUT reg, fan1_target sets SET_CNT reg, both unconditionally
removed all DT and platform_data knobs available via sysfs
updated documentation files to reflect two previous changes
Changes since v2:
set ref_clk value to 32768 if not overloaded
fixed multi-line comment format in g762.h
removed static const G762_DEFAULT_PDATA in g762.h for a function
CodingStyle: add spaces between operatoirs when missing
check return value of i2c_smbus_{read,write}_byte_data()
remove { } is not needed in single-statement conditionals
introduced G762_ATTR_VAL() to allow sparse init of platform_data struc
changed missed reference to linear mode for DC mode
Changes since v1
Changed author
removed bad tabs
Provide datasheet link w/o fud in g762 documentation
removed documentation for removed fan_gear_mode sysfs entry
removed tested-by from patch
removed FSF address in header file
removed useless include of <linux/slab.h>
removed useless parenthesis against HZ in define
use spaces around binary operators
use i2c_smbus_{read,write}_byte_data() instead of g762_{read,write}_value()
use return value of i2c_smbus_write_byte_data()
use true for initializing boolean
removed useless blank lines
do not enforce single return point rule where less readable
use dev_err() and dev_dbg() instead of dev_info() when it makes sense
remove leading '&' for function passed as pointers
allow passing parameter via platform_data struct for non-DT enabled boards
set data->valid to false when config is modified
s/linear/DC/ for mode (g762 datasheet uses linear)
more tests on rpm_from_cnt() and cnt_from_rpm() formula
dont overload
Changes since v0
removed forward declaration
use bool for valid field instead of bit field.
protect macro args
fixed typo in subject line
Added mention for G763 support in Kconfig
fixed typo in driver name in Kconfig
do not use DRVNAME in i2c_device_id g762_id[]
Following discussions, kept DEVICE_ATTR (i.e. no switch to SENSOR_DEVICE_ATTR)
removed useless casts when flipping bit values
Sanity check user input value (e.g. to prevent 256 to silenty become 0)
Added extra lines for multi line comments when needed
removed various testing knobs
make removed knobs available via DT
passed checkpatch script on the patch
removed useless lock protection againt clk setting
moved all setter at the beginning of the file
removed bad (u16) casts in g762_write_value() calls
Documentation/devicetree/bindings/hwmon/g762.txt | 47 +
Documentation/hwmon/g762 | 65 ++
drivers/hwmon/Kconfig | 10 +
drivers/hwmon/Makefile | 1 +
drivers/hwmon/g762.c | 1134 ++++++++++++++++++++++
include/linux/platform_data/g762.h | 37 +
6 files changed, 1294 insertions(+)
create mode 100644 Documentation/devicetree/bindings/hwmon/g762.txt
create mode 100644 Documentation/hwmon/g762
create mode 100644 drivers/hwmon/g762.c
create mode 100644 include/linux/platform_data/g762.h
diff --git a/Documentation/devicetree/bindings/hwmon/g762.txt b/Documentation/devicetree/bindings/hwmon/g762.txt
new file mode 100644
index 0000000..25cc6d8
--- /dev/null
+++ b/Documentation/devicetree/bindings/hwmon/g762.txt
@@ -0,0 +1,47 @@
+GMT G762/G763 PWM Fan controller
+
+Required node properties:
+
+ - "compatible": must be either "gmt,g762" or "gmt,g763"
+ - "reg": I2C bus address of the device
+ - "clocks": a fixed clock providing input clock frequency
+ on CLK pin of the chip.
+
+Optional properties:
+
+ - "fan_startv": fan startup voltage. Accepted values are 0, 1, 2 and 3.
+ The higher the more.
+
+ - "pwm_polarity": pwm polarity. Accepted values are 0 (positive duty)
+ and 1 (negative duty).
+
+ - "fan_gear_mode": fan gear mode. Supported values are 0, 1 and 2.
+
+If an optional property is not set in .dts file, then current value is kept
+unmodified (e.g. u-boot installed value).
+
+Additional information on operational parameters for the device is available
+in Documentation/hwmon/g762. A detailed datasheet for the device is available
+at http://natisbad.org/NAS/refs/GMT_EDS-762_763-080710-0.2.pdf.
+
+Example g762 node:
+
+ clocks {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ g762_clk: fixedclk {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <8192>;
+ }
+ }
+
+ g762: g762@3e {
+ compatible = "gmt,g762";
+ reg = <0x3e>;
+ clocks = <&g762_clk>
+ fan_gear_mode = <0>; /* chip default */
+ fan_startv = <1>; /* chip default */
+ pwm_polarity = <0>; /* chip default */
+ };
diff --git a/Documentation/hwmon/g762 b/Documentation/hwmon/g762
new file mode 100644
index 0000000..923db9c
--- /dev/null
+++ b/Documentation/hwmon/g762
@@ -0,0 +1,65 @@
+Kernel driver g762
+==================
+
+The GMT G762 Fan Speed PWM Controller is connected directly to a fan
+and performs closed-loop or open-loop control of the fan speed. Two
+modes - PWM or DC - are supported by the device.
+
+For additional information, a detailed datasheet is available at
+http://natisbad.org/NAS/ref/GMT_EDS-762_763-080710-0.2.pdf. sysfs
+bindings are described in Documentation/hwmon/sysfs-interface.
+
+The following entries are available to the user in a subdirectory of
+/sys/bus/i2c/drivers/g762/ to control the operation of the device.
+This can be done manually using the following entries but is usually
+done via a userland daemon like fancontrol.
+
+Note that those entries do not provide ways to setup the specific
+hardware characteristics of the system (reference clock, pulses per
+fan revolution, ...); Those can be modified via devicetree bindings
+documented in Documentation/devicetree/bindings/hwmon/g762.txt or
+using a specific platform_data structure in board initialization
+file (see include/linux/platform_data/g762.h).
+
+ fan1_target: set desired fan speed. This only makes sense in closed-loop
+ fan speed control (i.e. when pwm1_enable is set to 2).
+
+ fan1_input: provide current fan rotation value in RPM as reported by
+ the fan to the device.
+
+ fan1_div: fan clock divisor. Supported value are 1, 2, 4 and 8.
+
+ fan1_pulses: number of pulses per fan revolution. Supported values
+ are 2 and 4.
+
+ fan1_fault: reports fan failure, i.e. no transition on fan gear pin for
+ about 0.7s (if the fan is not voluntarily set off).
+
+ fan1_alarm: in closed-loop control mode, if fan RPM value is 25% out
+ of the programmed value for over 6 seconds 'fan1_alarm' is
+ set to 1.
+
+ pwm1_enable: set current fan speed control mode i.e. 1 for manual fan
+ speed control (open-loop) via pwm1 described below, 2 for
+ automatic fan speed control (closed-loop) via fan1_target
+ above.
+
+ pwm1_mode: set or get fan driving mode: 1 for PWM mode, 0 for DC mode.
+
+ pwm1: get or set PWM fan control value in open-loop mode. This is an
+ integer value between 0 and 255. 0 stops the fan, 255 makes
+ it run at full speed.
+
+Both in PWM mode ('pwm1_mode' set to 1) and DC mode ('pwm1_mode' set to 0),
+when current fan speed control mode is open-loop ('pwm1_enable' set to 1),
+the fan speed is programmed by setting a value between 0 and 255 via 'pwm1'
+entry (0 stops the fan, 255 makes it run at full speed). In closed-loop mode
+('pwm1_enable' set to 2), the expected rotation speed in RPM can be passed to
+the chip via 'fan1_target'. In closed-loop mode, the target speed is compared
+with current speed (available via 'fan1_input') by the device and a feedback
+is performed to match that target value. The fan speed value is computed
+based on the parameters associated with the physical characteristics of the
+system: a reference clock source frequency, a number of pulses per fan
+revolution, etc.
+
+Note that the driver will update its values at most once per second.
diff --git a/drivers/hwmon/Kconfig b/drivers/hwmon/Kconfig
index 0428e8a..142bdf8 100644
--- a/drivers/hwmon/Kconfig
+++ b/drivers/hwmon/Kconfig
@@ -456,6 +456,16 @@ config SENSORS_G760A
This driver can also be built as a module. If so, the module
will be called g760a.
+config SENSORS_G762
+ tristate "GMT G762 and G763"
+ depends on I2C
+ help
+ If you say yes here you get support for Global Mixed-mode
+ Technology Inc G762 and G763 fan speed PWM controller chips.
+
+ This driver can also be built as a module. If so, the module
+ will be called g762.
+
config SENSORS_GL518SM
tristate "Genesys Logic GL518SM"
depends on I2C
diff --git a/drivers/hwmon/Makefile b/drivers/hwmon/Makefile
index d17d3e6..4f0fb52 100644
--- a/drivers/hwmon/Makefile
+++ b/drivers/hwmon/Makefile
@@ -60,6 +60,7 @@ obj-$(CONFIG_SENSORS_F75375S) += f75375s.o
obj-$(CONFIG_SENSORS_FAM15H_POWER) += fam15h_power.o
obj-$(CONFIG_SENSORS_FSCHMD) += fschmd.o
obj-$(CONFIG_SENSORS_G760A) += g760a.o
+obj-$(CONFIG_SENSORS_G762) += g762.o
obj-$(CONFIG_SENSORS_GL518SM) += gl518sm.o
obj-$(CONFIG_SENSORS_GL520SM) += gl520sm.o
obj-$(CONFIG_SENSORS_GPIO_FAN) += gpio-fan.o
diff --git a/drivers/hwmon/g762.c b/drivers/hwmon/g762.c
new file mode 100644
index 0000000..e9da8e7
--- /dev/null
+++ b/drivers/hwmon/g762.c
@@ -0,0 +1,1134 @@
+/*
+ * g762 - Driver for the Global Mixed-mode Technology Inc. fan speed
+ * PWM controller chips from G762 family, i.e. G762 and G763
+ *
+ * Copyright (C) 2013, Arnaud EBALARD <arno@xxxxxxxxxxxx>
+ *
+ * This work is based on a basic version for 2.6.31 kernel developed
+ * by Olivier Mouchet for LaCie. Updates and correction have been
+ * performed to run on recent kernels. Additional features, like the
+ * ability to configure various characteristics via .dts file or
+ * board init file have been added. Detailed datasheet on which this
+ * development is based is available here:
+ *
+ * http://natisbad.org/NAS/refs/GMT_EDS-762_763-080710-0.2.pdf
+ *
+ * Headers from previous developments have been kept below:
+ *
+ * Copyright (c) 2009 LaCie
+ *
+ * Author: Olivier Mouchet <olivier.mouchet@xxxxxxxxx>
+ *
+ * based on g760a code written by Herbert Valerio Riedel <hvr@xxxxxxx>
+ * Copyright (C) 2007 Herbert Valerio Riedel <hvr@xxxxxxx>
+ *
+ * g762: minimal datasheet available at:
+ * http://www.gmt.com.tw/product/datasheet/EDS-762_3.pdf
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation.
+ */
+
+#include <linux/device.h>
+#include <linux/module.h>
+#include <linux/init.h>
+#include <linux/jiffies.h>
+#include <linux/i2c.h>
+#include <linux/hwmon.h>
+#include <linux/hwmon-sysfs.h>
+#include <linux/err.h>
+#include <linux/mutex.h>
+#include <linux/kernel.h>
+#include <linux/clk.h>
+#include <linux/of.h>
+#include <linux/of_device.h>
+#include <linux/platform_data/g762.h>
+
+#define DRVNAME "g762"
+
+static const struct i2c_device_id g762_id[] = {
+ { "g762", 0 },
+ { "g763", 0 },
+ { }
+};
+MODULE_DEVICE_TABLE(i2c, g762_id);
+
+enum g762_regs {
+ G762_REG_SET_CNT = 0x00,
+ G762_REG_ACT_CNT = 0x01,
+ G762_REG_FAN_STA = 0x02,
+ G762_REG_SET_OUT = 0x03,
+ G762_REG_FAN_CMD1 = 0x04,
+ G762_REG_FAN_CMD2 = 0x05,
+};
+
+/* Config register bits */
+#define G762_REG_FAN_CMD1_DET_FAN_FAIL 0x80 /* enable fan_fail signal */
+#define G762_REG_FAN_CMD1_DET_FAN_OOC 0x40 /* enable fan_out_of_control */
+#define G762_REG_FAN_CMD1_OUT_MODE 0x20 /* out mode: PWM or DC */
+#define G762_REG_FAN_CMD1_FAN_MODE 0x10 /* fan mode: closed/open-loop */
+#define G762_REG_FAN_CMD1_CLK_DIV_ID1 0x08 /* clock divisor value */
+#define G762_REG_FAN_CMD1_CLK_DIV_ID0 0x04
+#define G762_REG_FAN_CMD1_PWM_POLARITY 0x02 /* PWM polarity */
+#define G762_REG_FAN_CMD1_PULSE_PER_REV 0x01 /* pulse per fan revolution */
+
+#define G762_REG_FAN_CMD2_GEAR_MODE_1 0x08 /* fan gear mode */
+#define G762_REG_FAN_CMD2_GEAR_MODE_0 0x04
+#define G762_REG_FAN_CMD2_FAN_STARTV_1 0x02 /* fan startup voltage */
+#define G762_REG_FAN_CMD2_FAN_STARTV_0 0x01
+
+#define G762_REG_FAN_STA_FAIL 0x02 /* fan fail */
+#define G762_REG_FAN_STA_OOC 0x01 /* fan out of control */
+
+/* Config register values */
+#define G762_OUT_MODE_PWM 1
+#define G762_OUT_MODE_DC 0
+
+#define G762_FAN_MODE_CLOSED_LOOP 2
+#define G762_FAN_MODE_OPEN_LOOP 1
+
+#define G762_PWM_POLARITY_NEGATIVE 1
+#define G762_PWM_POLARITY_POSITIVE 0
+
+/* Register data is read (and cached) at most once per second. */
+#define G762_UPDATE_INTERVAL HZ
+
+/*
+ * Extract pulse count per fan revolution value (2 or 4) from given
+ * FAN_CMD1 register value.
+ */
+#define G762_PULSE_FROM_REG(reg) \
+ ((((reg) & G762_REG_FAN_CMD1_PULSE_PER_REV) + 1) << 1)
+
+/*
+ * Extract fan clock divisor (1, 2, 4 or 8) from given FAN_CMD1
+ * register value.
+ */
+#define G762_CLKDIV_FROM_REG(reg) \
+ (1 << (((reg) & (G762_REG_FAN_CMD1_CLK_DIV_ID0 | \
+ G762_REG_FAN_CMD1_CLK_DIV_ID1)) >> 2))
+
+/*
+ * Extract fan gear mode multiplier value (0, 2 or 4) from given
+ * FAN_CMD2 register value.
+ */
+#define G762_GEARMULT_FROM_REG(reg) \
+ (1 << (((reg) & (G762_REG_FAN_CMD2_GEAR_MODE_0 | \
+ G762_REG_FAN_CMD2_GEAR_MODE_1)) >> 2))
+
+struct g762_data {
+ struct i2c_client *client;
+ struct device *hwmon_dev;
+
+ /* update mutex */
+ struct mutex update_lock;
+
+ /* board specific parameters. */
+ u32 clk;
+
+ /* g762 register cache */
+ bool valid;
+ unsigned long last_updated; /* in jiffies */
+
+ u8 set_cnt; /* controls fan rotation speed in closed-loop mode */
+ u8 act_cnt; /* provides access to current fan RPM value */
+ u8 fan_sta; /* bit 0: set when actual fan speed is more than
+ * 25% outside requested fan speed
+ * bit 1: set when no transition occurs on fan
+ * pin for 0.7s
+ */
+ u8 set_out; /* controls fan rotation speed in open-loop mode */
+ u8 fan_cmd1; /* 0: FG_PLS_ID0 FG pulses count per revolution
+ * 0: 2 counts per revolution
+ * 1: 4 counts per revolution
+ * 1: PWM_POLARITY 1: negative_duty
+ * 0: positive_duty
+ * 2,3: [FG_CLOCK_ID0, FG_CLK_ID1]
+ * 00: Divide fan clock by 1
+ * 01: Divide fan clock by 2
+ * 10: Divide fan clock by 4
+ * 11: Divide fan clock by 8
+ * 4: FAN_MODE 1:closed-loop, 0:open-loop
+ * 5: OUT_MODE 1:PWM, 0:DC
+ * 6: DET_FAN_OOC enable "fan ooc" status
+ * 7: DET_FAN_FAIL enable "fan fail" status
+ */
+ u8 fan_cmd2; /* 0,1: FAN_STARTV 0,1,2,3 -> 0,32,64,96 dac_code
+ * 2,3: FG_GEAR_MODE
+ * 00: multiplier = 1
+ * 01: multiplier = 2
+ * 10: multiplier = 4
+ * 4: Mask ALERT# (g763 only)
+ */
+};
+
+/*
+ * Convert count value from fan controller register (FAN_SET_CNT) into fan
+ * speed RPM value. Note that the datasheet documents a basic formula;
+ * influence of additional parameters (fan clock divisor, fan gear mode)
+ * have been infered from examples in the datasheet and tests.
+ */
+static inline unsigned int rpm_from_cnt(u8 cnt, u32 clk, u16 p,
+ u8 clk_div, u8 gear_mult)
+{
+ if (cnt == 0xff) /* cnt to 255 stops the fan */
+ return 0;
+
+ return (clk * 30 * gear_mult) / ((cnt ? cnt : 1) * p * clk_div);
+}
+
+/*
+ * Convert fan RPM value from sysfs into count value for fan controller
+ * register (FAN_SET_CNT).
+ */
+static inline unsigned char cnt_from_rpm(u32 rpm, u32 clk, u16 p,
+ u8 clk_div, u8 gear_mult)
+{
+ if (!rpm) /* to stop the fan, set cnt to 255 */
+ return 0xff;
+
+ return clamp_val(((clk * 30 * gear_mult) / (rpm * p * clk_div)),
+ 0, 255);
+}
+
+/* helper to grab and cache data, at most one time per second */
+static struct g762_data *g762_update_client(struct device *dev)
+{
+ struct i2c_client *client = to_i2c_client(dev);
+ struct g762_data *data = i2c_get_clientdata(client);
+ int ret = 0;
+
+ mutex_lock(&data->update_lock);
+ if (time_before(jiffies, data->last_updated + G762_UPDATE_INTERVAL) &&
+ likely(data->valid))
+ goto out;
+
+ ret = i2c_smbus_read_byte_data(client, G762_REG_SET_CNT);
+ if (ret < 0)
+ goto out;
+ data->set_cnt = ret;
+
+ ret = i2c_smbus_read_byte_data(client, G762_REG_ACT_CNT);
+ if (ret < 0)
+ goto out;
+ data->act_cnt = ret;
+
+ ret = i2c_smbus_read_byte_data(client, G762_REG_FAN_STA);
+ if (ret < 0)
+ goto out;
+ data->fan_sta = ret;
+
+ ret = i2c_smbus_read_byte_data(client, G762_REG_SET_OUT);
+ if (ret < 0)
+ goto out;
+ data->set_out = ret;
+
+ ret = i2c_smbus_read_byte_data(client, G762_REG_FAN_CMD1);
+ if (ret < 0)
+ goto out;
+ data->fan_cmd1 = ret;
+
+ ret = i2c_smbus_read_byte_data(client, G762_REG_FAN_CMD2);
+ if (ret < 0)
+ goto out;
+ data->fan_cmd2 = ret;
+
+ data->last_updated = jiffies;
+ data->valid = true;
+ out:
+ mutex_unlock(&data->update_lock);
+
+ if (ret < 0) /* upon error, encode it in return value */
+ data = ERR_PTR(ret);
+
+ return data;
+}
+
+/* helpers for writing hardware parameters */
+
+/*
+ * Set input clock frequency received on CLK pin of the chip. Accepted values
+ * are between 0 and 0xffffff. If zero is given, then default frequency
+ * (32,768Hz) is used. Note that clock frequency is a characteristic of the
+ * system but an internal parameter, i.e. value is not passed to the device.
+ */
+static int do_set_clk_freq(struct device *dev, unsigned long val)
+{
+ struct i2c_client *client = to_i2c_client(dev);
+ struct g762_data *data = i2c_get_clientdata(client);
+
+ if (val > 0xffffff)
+ return -EINVAL;
+ if (!val)
+ val = 32768;
+
+ data->clk = val;
+
+ return 0;
+}
+
+/* Set pwm mode. Accepts either 0 (PWM mode) or 1 (DC mode) */
+static int do_set_pwm_mode(struct device *dev, unsigned long val)
+{
+ struct i2c_client *client = to_i2c_client(dev);
+ struct g762_data *data = g762_update_client(dev);
+ int ret = -EINVAL;
+
+ if (IS_ERR(data))
+ return PTR_ERR(data);
+
+ mutex_lock(&data->update_lock);
+ switch (val) {
+ case G762_OUT_MODE_PWM:
+ data->fan_cmd1 |= G762_REG_FAN_CMD1_OUT_MODE;
+ break;
+ case G762_OUT_MODE_DC:
+ data->fan_cmd1 &= ~G762_REG_FAN_CMD1_OUT_MODE;
+ break;
+ default:
+ goto out;
+ }
+ ret = i2c_smbus_write_byte_data(client, G762_REG_FAN_CMD1,
+ data->fan_cmd1);
+ data->valid = false;
+ out:
+ mutex_unlock(&data->update_lock);
+
+ return ret;
+}
+
+/* Set fan clock divisor. Accepts either 1, 2, 4 or 8. */
+static int do_set_fan_div(struct device *dev, unsigned long val)
+{
+ struct i2c_client *client = to_i2c_client(dev);
+ struct g762_data *data = g762_update_client(dev);
+ int ret = -EINVAL;
+
+ if (IS_ERR(data))
+ return PTR_ERR(data);
+
+ mutex_lock(&data->update_lock);
+ switch (val) {
+ case 1:
+ data->fan_cmd1 &= ~G762_REG_FAN_CMD1_CLK_DIV_ID0;
+ data->fan_cmd1 &= ~G762_REG_FAN_CMD1_CLK_DIV_ID1;
+ break;
+ case 2:
+ data->fan_cmd1 |= G762_REG_FAN_CMD1_CLK_DIV_ID0;
+ data->fan_cmd1 &= ~G762_REG_FAN_CMD1_CLK_DIV_ID1;
+ break;
+ case 4:
+ data->fan_cmd1 &= ~G762_REG_FAN_CMD1_CLK_DIV_ID0;
+ data->fan_cmd1 |= G762_REG_FAN_CMD1_CLK_DIV_ID1;
+ break;
+ case 8:
+ data->fan_cmd1 |= G762_REG_FAN_CMD1_CLK_DIV_ID0;
+ data->fan_cmd1 |= G762_REG_FAN_CMD1_CLK_DIV_ID1;
+ break;
+ default:
+ goto out;
+ }
+ ret = i2c_smbus_write_byte_data(client, G762_REG_FAN_CMD1,
+ data->fan_cmd1);
+ data->valid = false;
+ out:
+ mutex_unlock(&data->update_lock);
+
+ return ret;
+}
+
+/* Set fan gear mode. Accepts either 0, 1 or 2. */
+static int do_set_fan_gear_mode(struct device *dev, unsigned long val)
+{
+ struct i2c_client *client = to_i2c_client(dev);
+ struct g762_data *data = g762_update_client(dev);
+ int ret = -EINVAL;
+
+ if (IS_ERR(data))
+ return PTR_ERR(data);
+
+ mutex_lock(&data->update_lock);
+ switch (val) {
+ case 0:
+ data->fan_cmd2 &= ~G762_REG_FAN_CMD2_GEAR_MODE_0;
+ data->fan_cmd2 &= ~G762_REG_FAN_CMD2_GEAR_MODE_1;
+ break;
+ case 1:
+ data->fan_cmd2 |= G762_REG_FAN_CMD2_GEAR_MODE_0;
+ data->fan_cmd2 &= ~G762_REG_FAN_CMD2_GEAR_MODE_1;
+ break;
+ case 2:
+ data->fan_cmd2 &= ~G762_REG_FAN_CMD2_GEAR_MODE_0;
+ data->fan_cmd2 |= G762_REG_FAN_CMD2_GEAR_MODE_1;
+ break;
+ default:
+ goto out;
+ }
+ ret = i2c_smbus_write_byte_data(client, G762_REG_FAN_CMD2,
+ data->fan_cmd2);
+ data->valid = false;
+ out:
+ mutex_unlock(&data->update_lock);
+
+ return ret;
+}
+
+/* Set number of fan pulses per revolution. Accepts either 2 or 4. */
+static int do_set_fan_pulses(struct device *dev, unsigned long val)
+{
+ struct i2c_client *client = to_i2c_client(dev);
+ struct g762_data *data = g762_update_client(dev);
+ int ret = -EINVAL;
+
+ if (IS_ERR(data))
+ return PTR_ERR(data);
+
+ mutex_lock(&data->update_lock);
+ switch (val) {
+ case 2:
+ data->fan_cmd1 &= ~G762_REG_FAN_CMD1_PULSE_PER_REV;
+ break;
+ case 4:
+ data->fan_cmd1 |= G762_REG_FAN_CMD1_PULSE_PER_REV;
+ break;
+ default:
+ goto out;
+ }
+ ret = i2c_smbus_write_byte_data(client, G762_REG_FAN_CMD1,
+ data->fan_cmd1);
+ data->valid = false;
+ out:
+ mutex_unlock(&data->update_lock);
+
+ return ret;
+}
+
+/* Set fan mode. Accepts either 1 (open-loop) or 2 (closed-loop). */
+static int do_set_pwm_enable(struct device *dev, unsigned long val)
+{
+ struct i2c_client *client = to_i2c_client(dev);
+ struct g762_data *data = g762_update_client(dev);
+ int ret = -EINVAL;
+
+ if (IS_ERR(data))
+ return PTR_ERR(data);
+
+ mutex_lock(&data->update_lock);
+ switch (val) {
+ case G762_FAN_MODE_OPEN_LOOP:
+ data->fan_cmd1 &= ~G762_REG_FAN_CMD1_FAN_MODE;
+ /*
+ * BUG FIX: if SET_CNT register value is 255 then, for some
+ * unknown reason, fan will not rotate as expected, no matter
+ * the value of SET_OUT (to be specific, this seems to happen
+ * only in PWM mode). To workaround this bug, we give SET_CNT
+ * value of 254 if it is 255 when switching to open-loop.
+ */
+ if (data->set_cnt == 0xff)
+ i2c_smbus_write_byte_data(client, G762_REG_SET_CNT,
+ 254);
+ break;
+ case G762_FAN_MODE_CLOSED_LOOP:
+ data->fan_cmd1 |= G762_REG_FAN_CMD1_FAN_MODE;
+ break;
+ default:
+ goto out;
+ }
+
+ ret = i2c_smbus_write_byte_data(client, G762_REG_FAN_CMD1,
+ data->fan_cmd1);
+ data->valid = false;
+ out:
+ mutex_unlock(&data->update_lock);
+
+ return ret;
+}
+
+/* Set PWM polarity. Accepts either 0 (positive duty) or 1 (negative duty) */
+static int do_set_pwm_polarity(struct device *dev, unsigned long val)
+{
+ struct i2c_client *client = to_i2c_client(dev);
+ struct g762_data *data = g762_update_client(dev);
+ int ret = -EINVAL;
+
+ if (IS_ERR(data))
+ return PTR_ERR(data);
+
+ mutex_lock(&data->update_lock);
+ switch (val) {
+ case G762_PWM_POLARITY_POSITIVE:
+ data->fan_cmd1 &= ~G762_REG_FAN_CMD1_PWM_POLARITY;
+ break;
+ case G762_PWM_POLARITY_NEGATIVE:
+ data->fan_cmd1 |= G762_REG_FAN_CMD1_PWM_POLARITY;
+ break;
+ default:
+ goto out;
+ }
+ ret = i2c_smbus_write_byte_data(client, G762_REG_FAN_CMD1,
+ data->fan_cmd1);
+ data->valid = false;
+ out:
+ mutex_unlock(&data->update_lock);
+
+ return ret;
+}
+
+/*
+ * Set pwm value. Accepts values between 0 (stops the fan) and
+ * 255 (full speed). This only makes sense in open-loop mode.
+ */
+static int do_set_pwm(struct device *dev, unsigned long val)
+{
+ struct i2c_client *client = to_i2c_client(dev);
+ struct g762_data *data = i2c_get_clientdata(client);
+ int ret;
+
+ if (val > 255)
+ return -EINVAL;
+
+ mutex_lock(&data->update_lock);
+ ret = i2c_smbus_write_byte_data(client, G762_REG_SET_OUT, val);
+ data->valid = false;
+ mutex_unlock(&data->update_lock);
+
+ return ret;
+}
+
+/* Set fan RPM value. This only makes sense in closed-loop mode. */
+static int do_set_fan_target(struct device *dev, unsigned long val)
+{
+ struct i2c_client *client = to_i2c_client(dev);
+ struct g762_data *data = g762_update_client(dev);
+ int ret;
+
+ if (IS_ERR(data))
+ return PTR_ERR(data);
+
+ mutex_lock(&data->update_lock);
+ data->set_cnt = cnt_from_rpm(val, data->clk,
+ G762_PULSE_FROM_REG(data->fan_cmd1),
+ G762_CLKDIV_FROM_REG(data->fan_cmd1),
+ G762_GEARMULT_FROM_REG(data->fan_cmd2));
+ ret = i2c_smbus_write_byte_data(client, G762_REG_SET_CNT,
+ data->set_cnt);
+ data->valid = false;
+ mutex_unlock(&data->update_lock);
+
+ return ret;
+}
+
+/* Enable/disable fan failure detection. Accepted values are 1 and 0. */
+static int do_fan_failure_detection_toggle(struct device *dev,
+ unsigned long enable)
+{
+ struct i2c_client *client = to_i2c_client(dev);
+ struct g762_data *data = g762_update_client(dev);
+ int ret = -EINVAL;
+
+ if (IS_ERR(data))
+ return PTR_ERR(data);
+
+ mutex_lock(&data->update_lock);
+ switch (enable) {
+ case 0:
+ data->fan_cmd1 &= ~G762_REG_FAN_CMD1_DET_FAN_FAIL;
+ break;
+ case 1:
+ data->fan_cmd1 |= G762_REG_FAN_CMD1_DET_FAN_FAIL;
+ break;
+ default:
+ goto out;
+ }
+ ret = i2c_smbus_write_byte_data(client, G762_REG_FAN_CMD1,
+ data->fan_cmd1);
+ data->valid = false;
+ out:
+ mutex_unlock(&data->update_lock);
+
+ return ret;
+}
+
+/* Enable/disable fan out of control detection. Accepted values are 1 and 0 */
+static int do_fan_ooc_detection_toggle(struct device *dev, unsigned int enable)
+{
+ struct i2c_client *client = to_i2c_client(dev);
+ struct g762_data *data = g762_update_client(dev);
+ int ret = -EINVAL;
+
+ if (IS_ERR(data))
+ return PTR_ERR(data);
+
+ mutex_lock(&data->update_lock);
+ switch (enable) {
+ case 0:
+ data->fan_cmd1 &= ~G762_REG_FAN_CMD1_DET_FAN_OOC;
+ break;
+ case 1:
+ data->fan_cmd1 |= G762_REG_FAN_CMD1_DET_FAN_OOC;
+ break;
+ default:
+ goto out;
+ }
+ ret = i2c_smbus_write_byte_data(client, G762_REG_FAN_CMD1,
+ data->fan_cmd1);
+ out:
+ mutex_unlock(&data->update_lock);
+
+ return ret;
+}
+
+/* Set fan startup voltage. Accepted values are either 0, 1, 2 or 3. */
+static int do_set_fan_startv(struct device *dev, unsigned long val)
+{
+ struct i2c_client *client = to_i2c_client(dev);
+ struct g762_data *data = g762_update_client(dev);
+ int ret = -EINVAL;
+
+ if (IS_ERR(data))
+ return PTR_ERR(data);
+
+ mutex_lock(&data->update_lock);
+ switch (val) {
+ case 0:
+ data->fan_cmd2 &= ~G762_REG_FAN_CMD2_FAN_STARTV_0;
+ data->fan_cmd2 &= ~G762_REG_FAN_CMD2_FAN_STARTV_1;
+ break;
+ case 1:
+ data->fan_cmd2 |= G762_REG_FAN_CMD2_FAN_STARTV_0;
+ data->fan_cmd2 &= ~G762_REG_FAN_CMD2_FAN_STARTV_1;
+ break;
+ case 2:
+ data->fan_cmd2 &= ~G762_REG_FAN_CMD2_FAN_STARTV_0;
+ data->fan_cmd2 |= G762_REG_FAN_CMD2_FAN_STARTV_1;
+ break;
+ case 3:
+ data->fan_cmd2 |= G762_REG_FAN_CMD2_FAN_STARTV_0;
+ data->fan_cmd2 |= G762_REG_FAN_CMD2_FAN_STARTV_1;
+ break;
+ default:
+ goto out;
+ }
+ ret = i2c_smbus_write_byte_data(client, G762_REG_FAN_CMD2,
+ data->fan_cmd2);
+ data->valid = false;
+ out:
+ mutex_unlock(&data->update_lock);
+
+ return ret;
+}
+
+/*
+ * Helper to import hardware characteristics from .dts file and push
+ * those to the chip.
+ */
+
+#ifdef CONFIG_OF
+static struct of_device_id g762_dt_match[] = {
+ { .compatible = "gmt,g762" },
+ { .compatible = "gmt,g763" },
+ { },
+};
+
+static int g762_of_prop_import_one(struct i2c_client *client,
+ const char *pname,
+ int (*psetter)(struct device *dev,
+ unsigned long val))
+{
+ const __be32 *prop;
+ int len, ret = 0;
+ u32 pval;
+
+ prop = of_get_property(client->dev.of_node, pname, &len);
+ if (prop && len == sizeof(u32)) {
+ pval = be32_to_cpu(prop[0]);
+ dev_dbg(&client->dev, "found %s (%d)\n", pname, pval);
+ } else {
+ goto out;
+ }
+
+ ret = (*psetter)(&client->dev, pval);
+ if (ret)
+ dev_err(&client->dev, "unable to set %s (%d)\n", pname, pval);
+
+out:
+ return ret;
+}
+
+static int g762_of_prop_import(struct i2c_client *client)
+{
+ unsigned long clk_freq;
+ struct clk *clk;
+ int ret = 0;
+
+ if (!client->dev.of_node)
+ return ret;
+
+ /* First, grab clock (a required property), enable it, get
+ * (fixed) clock frequency and store it */
+ clk = of_clk_get(client->dev.of_node, 0);
+ if (IS_ERR(clk)) {
+ dev_err(&client->dev, "failed to get clock\n");
+ ret = PTR_ERR(clk);
+ goto out;
+ }
+
+ ret = clk_prepare_enable(clk);
+ if (ret) {
+ dev_err(&client->dev, "failed to enable clock\n");
+ goto out;
+ }
+
+ clk_freq = clk_get_rate(clk);
+ ret = do_set_clk_freq(&client->dev, clk_freq);
+ if (ret) {
+ dev_err(&client->dev, "invalid clock freq %lu\n", clk_freq);
+ goto out;
+ }
+
+ /* Now import and commit optional properties */
+ ret = g762_of_prop_import_one(client, "fan_gear_mode",
+ do_set_fan_gear_mode);
+ if (ret)
+ goto out;
+
+ ret = g762_of_prop_import_one(client, "pwm_polarity",
+ do_set_pwm_polarity);
+ if (ret)
+ goto out;
+
+ ret = g762_of_prop_import_one(client, "fan_startv",
+ do_set_fan_startv);
+
+ out:
+ return ret;
+}
+
+#else
+static int g762_of_prop_import(struct i2c_client *client,
+ struct g762_platform_data *pdata) { return 0 }
+#endif
+
+/*
+ * Helper to import hardware characteristics from .dts file and push
+ * those to the chip.
+ */
+
+static int g762_pdata_prop_import(struct i2c_client *client)
+{
+ struct g762_platform_data *pdata = client->dev.platform_data;
+ int ret;
+
+ if (!pdata)
+ return 0;
+
+ ret = do_set_fan_gear_mode(&client->dev, pdata->fan_gear_mode);
+ if (ret)
+ goto out;
+
+ ret = do_set_pwm_polarity(&client->dev, pdata->pwm_polarity);
+ if (ret)
+ goto out;
+
+ ret = do_set_fan_startv(&client->dev, pdata->fan_startv);
+ if (ret)
+ goto out;
+
+ ret = do_set_fan_startv(&client->dev, pdata->fan_startv);
+
+ out:
+ return ret;
+}
+
+/*
+ * sysfs attributes
+ */
+
+/*
+ * Read function for fan1_input sysfs file. Return current fan RPM value, or
+ * 0 if fan is out of control.
+ */
+static ssize_t get_fan_rpm(struct device *dev, struct device_attribute *da,
+ char *buf)
+{
+ struct g762_data *data = g762_update_client(dev);
+ unsigned int rpm = 0;
+
+ if (IS_ERR(data))
+ return PTR_ERR(data);
+
+ mutex_lock(&data->update_lock);
+ /* reverse logic: fan out of control reporting is enabled low */
+ if (data->fan_sta & G762_REG_FAN_STA_OOC) {
+ rpm = rpm_from_cnt(data->act_cnt, data->clk,
+ G762_PULSE_FROM_REG(data->fan_cmd1),
+ G762_CLKDIV_FROM_REG(data->fan_cmd1),
+ G762_GEARMULT_FROM_REG(data->fan_cmd2));
+ }
+ mutex_unlock(&data->update_lock);
+
+ return sprintf(buf, "%u\n", rpm);
+}
+
+/*
+ * Read and write functions for pwm1_mode sysfs file. Get and set fan speed
+ * control mode i.e. PWM (1) or DC (0).
+ */
+static ssize_t get_pwm_mode(struct device *dev, struct device_attribute *da,
+ char *buf)
+{
+ struct g762_data *data = g762_update_client(dev);
+
+ if (IS_ERR(data))
+ return PTR_ERR(data);
+
+ return sprintf(buf, "%d\n",
+ !!(data->fan_cmd1 & G762_REG_FAN_CMD1_OUT_MODE));
+}
+
+static ssize_t set_pwm_mode(struct device *dev, struct device_attribute *da,
+ const char *buf, size_t count)
+{
+ unsigned long val;
+ int ret;
+
+ if (kstrtoul(buf, 10, &val))
+ return -EINVAL;
+
+ ret = do_set_pwm_mode(dev, val);
+ if (ret < 0)
+ return ret;
+
+ return count;
+}
+
+/*
+ * Read and write functions for fan1_div sysfs file. Get and set fan
+ * controller prescaler value
+ */
+static ssize_t get_fan_div(struct device *dev,
+ struct device_attribute *da, char *buf)
+{
+ struct g762_data *data = g762_update_client(dev);
+
+ if (IS_ERR(data))
+ return PTR_ERR(data);
+
+ return sprintf(buf, "%d\n", G762_CLKDIV_FROM_REG(data->fan_cmd1));
+}
+
+static ssize_t set_fan_div(struct device *dev,
+ struct device_attribute *da,
+ const char *buf, size_t count)
+{
+ unsigned long val;
+ int ret;
+
+ if (kstrtoul(buf, 10, &val))
+ return -EINVAL;
+
+ ret = do_set_fan_div(dev, val);
+ if (ret < 0)
+ return ret;
+
+ return count;
+}
+
+/*
+ * Read and write functions for fan1_pulses sysfs file. Get and set number
+ * of tachometer pulses per fan revolution.
+ */
+static ssize_t get_fan_pulses(struct device *dev,
+ struct device_attribute *da, char *buf)
+{
+ struct g762_data *data = g762_update_client(dev);
+
+ if (IS_ERR(data))
+ return PTR_ERR(data);
+
+ return sprintf(buf, "%d\n", G762_PULSE_FROM_REG(data->fan_cmd1));
+}
+
+static ssize_t set_fan_pulses(struct device *dev,
+ struct device_attribute *da,
+ const char *buf, size_t count)
+{
+ unsigned long val;
+ int ret;
+
+ if (kstrtoul(buf, 10, &val))
+ return -EINVAL;
+
+ ret = do_set_fan_pulses(dev, val);
+ if (ret < 0)
+ return ret;
+
+ return count;
+}
+
+/*
+ * Read and write functions for pwm1_enable. Get and set fan speed control mode
+ * (i.e. closed or open-loop).
+ *
+ * Following documentation about hwmon's sysfs interface, a pwm1_enable node
+ * should accept followings:
+ *
+ * 0 : no fan speed control (i.e. fan at full speed)
+ * 1 : manual fan speed control enabled (use pwm[1-*]) (open-loop)
+ * 2+: automatic fan speed control enabled (use fan[1-*]_target) (closed-loop)
+ *
+ * but we do not accept 0 as this mode is not natively supported by the chip
+ * and it is not emulated by g762 driver. -EINVAL is returned in this case.
+ */
+static ssize_t get_pwm_enable(struct device *dev,
+ struct device_attribute *da, char *buf)
+{
+ struct g762_data *data = g762_update_client(dev);
+
+ if (IS_ERR(data))
+ return PTR_ERR(data);
+
+ return sprintf(buf, "%d\n",
+ (!!(data->fan_cmd1 & G762_REG_FAN_CMD1_FAN_MODE)) + 1);
+}
+
+static ssize_t set_pwm_enable(struct device *dev,
+ struct device_attribute *da,
+ const char *buf, size_t count)
+{
+ unsigned long val;
+ int ret;
+
+ if (kstrtoul(buf, 10, &val))
+ return -EINVAL;
+
+ ret = do_set_pwm_enable(dev, val);
+ if (ret < 0)
+ return ret;
+
+ return count;
+}
+
+/*
+ * Read and write functions for pwm1 sysfs file. Get and set pwm value
+ * (which affects fan speed) in open-loop mode. 0 stops the fan and 255
+ * makes it run at full speed.
+ */
+static ssize_t get_pwm(struct device *dev, struct device_attribute *da,
+ char *buf)
+{
+ struct g762_data *data = g762_update_client(dev);
+
+ if (IS_ERR(data))
+ return PTR_ERR(data);
+
+ return sprintf(buf, "%d\n", data->set_out);
+}
+
+static ssize_t set_pwm(struct device *dev, struct device_attribute *da,
+ const char *buf, size_t count)
+{
+ unsigned long val;
+ int ret;
+
+ if (kstrtoul(buf, 10, &val))
+ return -EINVAL;
+
+ ret = do_set_pwm(dev, val);
+ if (ret < 0)
+ return ret;
+
+ return count;
+}
+
+/*
+ * Read and write function for fan1_target sysfs file. Get/set the fan speed in
+ * closed-loop mode. Speed is given as a RPM value; then the chip will regulate
+ * the fan speed using pulses from fan tachometer.
+ *
+ * Refer to rpm_from_cnt() implementation above to get info about count number
+ * calculation.
+ *
+ * Also note that due to rounding errors it is possible that you don't read
+ * back exactly the value you have set.
+ */
+static ssize_t get_fan_target(struct device *dev, struct device_attribute *da,
+ char *buf)
+{
+ struct g762_data *data = g762_update_client(dev);
+ unsigned int rpm;
+ ssize_t ret;
+
+ if (IS_ERR(data))
+ return PTR_ERR(data);
+
+ mutex_lock(&data->update_lock);
+ rpm = rpm_from_cnt(data->set_cnt, data->clk,
+ G762_PULSE_FROM_REG(data->fan_cmd1),
+ G762_CLKDIV_FROM_REG(data->fan_cmd1),
+ G762_GEARMULT_FROM_REG(data->fan_cmd2));
+ ret = sprintf(buf, "%u\n", rpm);
+ mutex_unlock(&data->update_lock);
+
+ return ret;
+}
+
+static ssize_t set_fan_target(struct device *dev, struct device_attribute *da,
+ const char *buf, size_t count)
+{
+ unsigned long val;
+ int ret;
+
+ if (kstrtoul(buf, 10, &val))
+ return -EINVAL;
+
+ ret = do_set_fan_target(dev, val);
+ if (ret < 0)
+ return ret;
+
+ return count;
+}
+
+/* read function for fan1_fault sysfs file. */
+static ssize_t get_fan_failure(struct device *dev, struct device_attribute *da,
+ char *buf)
+{
+ struct g762_data *data = g762_update_client(dev);
+
+ if (IS_ERR(data))
+ return PTR_ERR(data);
+
+ return sprintf(buf, "%u\n", !!(data->fan_sta & G762_REG_FAN_STA_FAIL));
+}
+
+/*
+ * read function for fan1_alarm sysfs file. Note that OOC condition is
+ * enabled low
+ */
+static ssize_t get_fan_ooc(struct device *dev, struct device_attribute *da,
+ char *buf)
+{
+ struct g762_data *data = g762_update_client(dev);
+
+ if (IS_ERR(data))
+ return PTR_ERR(data);
+
+ return sprintf(buf, "%u\n", !(data->fan_sta & G762_REG_FAN_STA_OOC));
+}
+
+static DEVICE_ATTR(pwm1, S_IWUSR | S_IRUGO, get_pwm, set_pwm);
+static DEVICE_ATTR(pwm1_mode, S_IWUSR | S_IRUGO, get_pwm_mode, set_pwm_mode);
+static DEVICE_ATTR(pwm1_enable, S_IWUSR | S_IRUGO,
+ get_pwm_enable, set_pwm_enable);
+static DEVICE_ATTR(fan1_input, S_IRUGO, get_fan_rpm, NULL);
+static DEVICE_ATTR(fan1_alarm, S_IRUGO, get_fan_ooc, NULL);
+static DEVICE_ATTR(fan1_fault, S_IRUGO, get_fan_failure, NULL);
+static DEVICE_ATTR(fan1_target, S_IWUSR | S_IRUGO,
+ get_fan_target, set_fan_target);
+static DEVICE_ATTR(fan1_div, S_IWUSR | S_IRUGO, get_fan_div, set_fan_div);
+static DEVICE_ATTR(fan1_pulses, S_IWUSR | S_IRUGO,
+ get_fan_pulses, set_fan_pulses);
+
+/* Driver data */
+static struct attribute *g762_attributes[] = {
+ &dev_attr_fan1_input.attr,
+ &dev_attr_fan1_alarm.attr,
+ &dev_attr_fan1_fault.attr,
+ &dev_attr_fan1_target.attr,
+ &dev_attr_fan1_div.attr,
+ &dev_attr_fan1_pulses.attr,
+ &dev_attr_pwm1.attr,
+ &dev_attr_pwm1_mode.attr,
+ &dev_attr_pwm1_enable.attr,
+ NULL
+};
+
+static const struct attribute_group g762_group = {
+ .attrs = g762_attributes,
+};
+
+static int g762_probe(struct i2c_client *client, const struct i2c_device_id *id)
+{
+ struct g762_data *data;
+ int ret;
+
+ if (!i2c_check_functionality(client->adapter,
+ I2C_FUNC_SMBUS_BYTE_DATA))
+ return -ENODEV;
+
+ data = devm_kzalloc(&client->dev, sizeof(struct g762_data), GFP_KERNEL);
+ if (!data)
+ return -ENOMEM;
+
+ i2c_set_clientdata(client, data);
+ data->client = client;
+ mutex_init(&data->update_lock);
+
+ /* Enable fan protection and fan fail detection */
+ do_fan_ooc_detection_toggle(&client->dev, 1);
+ do_fan_failure_detection_toggle(&client->dev, 1);
+
+ /* Get configuration via DT xor platform_data */
+ if (client->dev.of_node)
+ ret = g762_of_prop_import(client);
+ else
+ ret = g762_pdata_prop_import(client);
+ if (ret)
+ goto out;
+
+ /* Register sysfs hooks */
+ ret = sysfs_create_group(&client->dev.kobj, &g762_group);
+ if (ret)
+ goto out;
+
+ data->hwmon_dev = hwmon_device_register(&client->dev);
+ if (IS_ERR(data->hwmon_dev)) {
+ ret = PTR_ERR(data->hwmon_dev);
+ goto sysfs_out;
+ }
+
+ return 0;
+
+ sysfs_out:
+ sysfs_remove_group(&client->dev.kobj, &g762_group);
+ out:
+ return ret;
+}
+
+static int g762_remove(struct i2c_client *client)
+{
+ struct g762_data *data = i2c_get_clientdata(client);
+
+ hwmon_device_unregister(data->hwmon_dev);
+ sysfs_remove_group(&client->dev.kobj, &g762_group);
+
+ return 0;
+}
+
+static struct i2c_driver g762_driver = {
+ .driver = {
+ .name = DRVNAME,
+ .owner = THIS_MODULE,
+ .of_match_table = of_match_ptr(g762_dt_match),
+ },
+ .probe = g762_probe,
+ .remove = g762_remove,
+ .id_table = g762_id,
+};
+
+module_i2c_driver(g762_driver);
+
+MODULE_AUTHOR("Arnaud EBALARD <arno@xxxxxxxxxxxx>");
+MODULE_DESCRIPTION("GMT G762/G763 driver");
+MODULE_LICENSE("GPL");
diff --git a/include/linux/platform_data/g762.h b/include/linux/platform_data/g762.h
new file mode 100644
index 0000000..d3c5128
--- /dev/null
+++ b/include/linux/platform_data/g762.h
@@ -0,0 +1,37 @@
+/*
+ * Platform data structure for g762 fan controller driver
+ *
+ * Copyright (C) 2013, Arnaud EBALARD <arno@xxxxxxxxxxxx>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
+ */
+#ifndef __LINUX_PLATFORM_DATA_G762_H__
+#define __LINUX_PLATFORM_DATA_G762_H__
+
+/*
+ * Following structure can be used to set g762 driver platform specific data
+ * during board init. Note that passing a sparse structure is possible but
+ * will result in non-specified attributes to be set to default value, hence
+ * overloading those installed during boot (e.g. by u-boot).
+ */
+
+struct g762_platform_data {
+ u32 fan_startv;
+ u32 fan_gear_mode;
+ u32 pwm_polarity;
+ u32 clk_freq;
+};
+
+#endif /* __LINUX_PLATFORM_DATA_G762_H__ */
--
1.7.10.4
_______________________________________________
lm-sensors mailing list
lm-sensors@xxxxxxxxxxxxxx
http://lists.lm-sensors.org/mailman/listinfo/lm-sensors
