This driver will replace the w83627ehf driver for NCT6775F and NCT6776F,
and provides support for NCT6779D.
This patch provides support for voltage monitor attributes.
Signed-off-by: Guenter Roeck <linux@xxxxxxxxxxxx>
---
Documentation/hwmon/nct6775 | 81 ++++
drivers/hwmon/Kconfig | 13 +
drivers/hwmon/Makefile | 1 +
drivers/hwmon/nct6775.c | 1021 +++++++++++++++++++++++++++++++++++++++++++
4 files changed, 1116 insertions(+)
create mode 100644 Documentation/hwmon/nct6775
create mode 100644 drivers/hwmon/nct6775.c
diff --git a/Documentation/hwmon/nct6775 b/Documentation/hwmon/nct6775
new file mode 100644
index 0000000..ccfd5cc
--- /dev/null
+++ b/Documentation/hwmon/nct6775
@@ -0,0 +1,81 @@
+Note
+====
+
+This driver supersedes the NCT6775F and NCT6776F support in the W83627EHF
+driver.
+
+Kernel driver NCT6775
+=====================
+
+Supported chips:
+ * Nuvoton NCT6775F/W83667HG-I
+ Prefix: 'nct6775'
+ Addresses scanned: ISA address retrieved from Super I/O registers
+ Datasheet: Available from Nuvoton upon request
+ * Nuvoton NCT6776F
+ Prefix: 'nct6776'
+ Addresses scanned: ISA address retrieved from Super I/O registers
+ Datasheet: Available from Nuvoton upon request
+ * Nuvoton NCT6779D
+ Prefix: 'nct6779'
+ Addresses scanned: ISA address retrieved from Super I/O registers
+ Datasheet: Available from Nuvoton upon request
+
+Authors:
+ Guenter Roeck <linux@xxxxxxxxxxxx>
+
+Description
+-----------
+
+This driver implements support for the Nuvoton NCT6775F, NCT6776F, and NCT6779D
+super I/O chips.
+
+The chips support up to 25 temperature monitoring sources. Up to 6 of those are
+direct temperature sensor inputs, the others are special sources such as PECI,
+PCH, and SMBUS. Depending on the chip type, 2 to 6 of the temperature sources
+can be monitored and compared against minimum, maximum, and critical
+temperatures. The driver reports up to 10 of the temperatures to the user.
+There are 4 to 5 fan rotation speed sensors, 8 to 15 analog voltage sensors,
+one VID, alarms with beep warnings (control unimplemented), and some automatic
+fan regulation strategies (plus manual fan control mode).
+
+The temperature sensor sources on all chips are configurable. The configured
+source for each of the temperature sensors is provided in tempX_label.
+
+Temperatures are measured in degrees Celsius and measurement resolution is
+either 1 degC or 0.5 degC, depending on the temperature source and
+configuration. An alarm is triggered when the temperature gets higher than
+the high limit; it stays on until the temperature falls below the hysteresis
+value. Alarms are only supported for temp1 to temp6, depending on the chip type.
+
+Fan rotation speeds are reported in RPM (rotations per minute). An alarm is
+triggered if the rotation speed has dropped below a programmable limit. On
+NCT6775F, fan readings can be divided by a programmable divider (1, 2, 4, 8,
+16, 32, 64 or 128) to give the readings more range or accuracy; the other chips
+do not have a fan speed divider. The driver sets the most suitable fan divisor
+itself; specifically, it doubles the divider value each time a fan speed reading
+returns an invalid value. Some fans might not be present because they share pins
+with other functions.
+
+Voltage sensors (also known as IN sensors) report their values in millivolts.
+An alarm is triggered if the voltage has crossed a programmable minimum
+or maximum limit.
+
+The driver supports automatic fan control mode known as Thermal Cruise.
+In this mode, the chip attempts to keep the measured temperature in a
+predefined temperature range. If the temperature goes out of range, fan
+is driven slower/faster to reach the predefined range again.
+
+The mode works for fan1-fan5.
+
+Usage Notes
+-----------
+
+On various ASUS boards with NCT6776F, it appears that CPUTIN is not really
+connected to anything and floats, or that it is connected to some non-standard
+temperature measurement device. As a result, the temperature reported on CPUTIN
+will not reflect a usable value. It often reports unreasonably high
+temperatures, and in some cases the reported temperature declines if the actual
+temperature increases (similar to the raw PECI temperature value - see PECI
+specification for details). CPUTIN should therefore be be ignored on ASUS
+boards. The CPU temperature on ASUS boards is reported from PECI 0.
diff --git a/drivers/hwmon/Kconfig b/drivers/hwmon/Kconfig
index 89ac1cb..b072fb8 100644
--- a/drivers/hwmon/Kconfig
+++ b/drivers/hwmon/Kconfig
@@ -877,6 +877,19 @@ config SENSORS_MCP3021
This driver can also be built as a module. If so, the module
will be called mcp3021.
+config SENSORS_NCT6775
+ tristate "Nuvoton NCT6775F, NCT6776F, NCT6779D"
+ depends on !PPC && EXPERIMENTAL
+ select HWMON_VID
+ help
+ If you say yes here you get support for the hardware monitoring
+ functionality of the Nuvoton NCT6775F, NCT6776F, and NCT6779D
+ Super-I/O chips. This driver replaces the w83627ehf driver for
+ NCT6775F and NCT6776F.
+
+ This driver can also be built as a module. If so, the module
+ will be called nct6775.
+
config SENSORS_NTC_THERMISTOR
tristate "NTC thermistor support"
help
diff --git a/drivers/hwmon/Makefile b/drivers/hwmon/Makefile
index 8d6d97e..b0898da 100644
--- a/drivers/hwmon/Makefile
+++ b/drivers/hwmon/Makefile
@@ -103,6 +103,7 @@ obj-$(CONFIG_SENSORS_MAX6650) += max6650.o
obj-$(CONFIG_SENSORS_MAX6697) += max6697.o
obj-$(CONFIG_SENSORS_MC13783_ADC)+= mc13783-adc.o
obj-$(CONFIG_SENSORS_MCP3021) += mcp3021.o
+obj-$(CONFIG_SENSORS_NCT6775) += nct6775.o
obj-$(CONFIG_SENSORS_NTC_THERMISTOR) += ntc_thermistor.o
obj-$(CONFIG_SENSORS_PC87360) += pc87360.o
obj-$(CONFIG_SENSORS_PC87427) += pc87427.o
diff --git a/drivers/hwmon/nct6775.c b/drivers/hwmon/nct6775.c
new file mode 100644
index 0000000..f75cd82
--- /dev/null
+++ b/drivers/hwmon/nct6775.c
@@ -0,0 +1,1021 @@
+/*
+ * nct6775 - Driver for the hardware monitoring functionality of
+ * Nuvoton NCT677x Super-I/O chips
+ *
+ * Copyright (C) 2012 Guenter Roeck <linux@xxxxxxxxxxxx>
+ *
+ * Derived from w83627ehf driver
+ * Copyright (C) 2005-2012 Jean Delvare <khali@xxxxxxxxxxxx>
+ * Copyright (C) 2006 Yuan Mu (Winbond),
+ * Rudolf Marek <r.marek@xxxxxxxxxxxx>
+ * David Hubbard <david.c.hubbard@xxxxxxxxx>
+ * Daniel J Blueman <daniel.blueman@xxxxxxxxx>
+ * Copyright (C) 2010 Sheng-Yuan Huang (Nuvoton) (PS00)
+ *
+ * Shamelessly ripped from the w83627hf driver
+ * Copyright (C) 2003 Mark Studebaker
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
+ *
+ *
+ * Supports the following chips:
+ *
+ * Chip #vin #fan #pwm #temp chip IDs man ID
+ * nct6775f 9 4 3 6+3 0xb470 0xc1 0x5ca3
+ * nct6776f 9 5 3 6+3 0xc330 0xc1 0x5ca3
+ * nct6779d 15 5 5 2+6 0xc560 0xc1 0x5ca3
+ *
+ * #temp lists the number of monitored temperature sources (first value) plus
+ * the number of directly connectable temperature sensors (second value).
+ */
+
+#define pr_fmt(fmt) KBUILD_MODNAME ": " fmt
+
+#include <linux/module.h>
+#include <linux/init.h>
+#include <linux/slab.h>
+#include <linux/jiffies.h>
+#include <linux/platform_device.h>
+#include <linux/hwmon.h>
+#include <linux/hwmon-sysfs.h>
+#include <linux/hwmon-vid.h>
+#include <linux/err.h>
+#include <linux/mutex.h>
+#include <linux/acpi.h>
+#include <linux/io.h>
+#include "lm75.h"
+
+enum kinds { nct6775, nct6776, nct6779 };
+
+/* used to set data->name = nct6775_device_names[data->sio_kind] */
+static const char * const nct6775_device_names[] = {
+ "nct6775",
+ "nct6776",
+ "nct6779",
+};
+
+static unsigned short force_id;
+module_param(force_id, ushort, 0);
+MODULE_PARM_DESC(force_id, "Override the detected device ID");
+
+#define DRVNAME "nct6775"
+
+/*
+ * Super-I/O constants and functions
+ */
+
+#define NCT6775_LD_HWM 0x0b
+#define NCT6775_LD_VID 0x0d
+
+#define SIO_REG_LDSEL 0x07 /* Logical device select */
+#define SIO_REG_DEVID 0x20 /* Device ID (2 bytes) */
+#define SIO_REG_ENABLE 0x30 /* Logical device enable */
+#define SIO_REG_ADDR 0x60 /* Logical device address (2 bytes) */
+
+#define SIO_NCT6775_ID 0xb470
+#define SIO_NCT6776_ID 0xc330
+#define SIO_NCT6779_ID 0xc560
+#define SIO_ID_MASK 0xFFF0
+
+static inline void
+superio_outb(int ioreg, int reg, int val)
+{
+ outb(reg, ioreg);
+ outb(val, ioreg + 1);
+}
+
+static inline int
+superio_inb(int ioreg, int reg)
+{
+ outb(reg, ioreg);
+ return inb(ioreg + 1);
+}
+
+static inline void
+superio_select(int ioreg, int ld)
+{
+ outb(SIO_REG_LDSEL, ioreg);
+ outb(ld, ioreg + 1);
+}
+
+static inline int
+superio_enter(int ioreg)
+{
+ /*
+ * Try to reserve <ioreg> and <ioreg + 1> for exclusive access.
+ */
+ if (!request_muxed_region(ioreg, 2, DRVNAME))
+ return -EBUSY;
+
+ outb(0x87, ioreg);
+ outb(0x87, ioreg);
+
+ return 0;
+}
+
+static inline void
+superio_exit(int ioreg)
+{
+ outb(0xaa, ioreg);
+ outb(0x02, ioreg);
+ outb(0x02, ioreg + 1);
+ release_region(ioreg, 2);
+}
+
+/*
+ * ISA constants
+ */
+
+#define IOREGION_ALIGNMENT (~7)
+#define IOREGION_OFFSET 5
+#define IOREGION_LENGTH 2
+#define ADDR_REG_OFFSET 0
+#define DATA_REG_OFFSET 1
+
+#define NCT6775_REG_BANK 0x4E
+#define NCT6775_REG_CONFIG 0x40
+
+/*
+ * Not currently used:
+ * REG_MAN_ID has the value 0x5ca3 for all supported chips.
+ * REG_CHIP_ID == 0x88/0xa1/0xc1 depending on chip model.
+ * REG_MAN_ID is at port 0x4f
+ * REG_CHIP_ID is at port 0x58
+ */
+
+#define NUM_REG_ALARM 4 /* Max number of alarm registers */
+
+/* Common and NCT6775 specific data */
+
+/* Voltage min/max registers for nr=7..14 are in bank 5 */
+
+static const u16 NCT6775_REG_IN_MAX[] = {
+ 0x2b, 0x2d, 0x2f, 0x31, 0x33, 0x35, 0x37, 0x554, 0x556, 0x558, 0x55a,
+ 0x55c, 0x55e, 0x560, 0x562 };
+static const u16 NCT6775_REG_IN_MIN[] = {
+ 0x2c, 0x2e, 0x30, 0x32, 0x34, 0x36, 0x38, 0x555, 0x557, 0x559, 0x55b,
+ 0x55d, 0x55f, 0x561, 0x563 };
+static const u16 NCT6775_REG_IN[] = {
+ 0x20, 0x21, 0x22, 0x23, 0x24, 0x25, 0x26, 0x550, 0x551, 0x552
+};
+
+#define NCT6775_REG_VBAT 0x5D
+
+static const u16 NCT6775_REG_ALARM[NUM_REG_ALARM] = { 0x459, 0x45A, 0x45B };
+
+/* 0..15 voltages, 16..23 fans, 24..31 temperatures */
+
+static const s8 NCT6775_ALARM_BITS[] = {
+ 0, 1, 2, 3, 8, 21, 20, 16, /* in0.. in7 */
+ 17, -1, -1, -1, -1, -1, -1, /* in8..in14 */
+ -1, /* unused */
+ 6, 7, 11, 10, 23, /* fan1..fan5 */
+ -1, -1, -1, /* unused */
+ 4, 5, 13, -1, -1, -1, /* temp1..temp6 */
+ 12, -1 }; /* intrusion0, intrusion1 */
+
+/* NCT6776 specific data */
+
+static const s8 NCT6776_ALARM_BITS[] = {
+ 0, 1, 2, 3, 8, 21, 20, 16, /* in0.. in7 */
+ 17, -1, -1, -1, -1, -1, -1, /* in8..in14 */
+ -1, /* unused */
+ 6, 7, 11, 10, 23, /* fan1..fan5 */
+ -1, -1, -1, /* unused */
+ 4, 5, 13, -1, -1, -1, /* temp1..temp6 */
+ 12, 9 }; /* intrusion0, intrusion1 */
+
+/* NCT6779 specific data */
+
+static const u16 NCT6779_REG_IN[] = {
+ 0x480, 0x481, 0x482, 0x483, 0x484, 0x485, 0x486, 0x487,
+ 0x488, 0x489, 0x48a, 0x48b, 0x48c, 0x48d, 0x48e };
+
+static const u16 NCT6779_REG_ALARM[NUM_REG_ALARM] = {
+ 0x459, 0x45A, 0x45B, 0x568 };
+
+static const s8 NCT6779_ALARM_BITS[] = {
+ 0, 1, 2, 3, 8, 21, 20, 16, /* in0.. in7 */
+ 17, 24, 25, 26, 27, 28, 29, /* in8..in14 */
+ -1, /* unused */
+ 6, 7, 11, 10, 23, /* fan1..fan5 */
+ -1, -1, -1, /* unused */
+ 4, 5, 13, -1, -1, -1, /* temp1..temp6 */
+ 12, 9 }; /* intrusion0, intrusion1 */
+
+/*
+ * Conversions
+ */
+
+/*
+ * Some of the voltage inputs have internal scaling, the tables below
+ * contain 8 (the ADC LSB in mV) * scaling factor * 100
+ */
+static const u16 scale_in[15] = {
+ 800, 800, 1600, 1600, 800, 800, 800, 1600, 1600, 800, 800, 800, 800,
+ 800, 800
+};
+
+static inline long in_from_reg(u8 reg, u8 nr)
+{
+ return DIV_ROUND_CLOSEST(reg * scale_in[nr], 100);
+}
+
+static inline u8 in_to_reg(u32 val, u8 nr)
+{
+ return clamp_val(DIV_ROUND_CLOSEST(val * 100, scale_in[nr]), 0, 255);
+}
+
+/*
+ * Data structures and manipulation thereof
+ */
+
+struct nct6775_data {
+ int addr; /* IO base of hw monitor block */
+ enum kinds kind;
+ const char *name;
+
+ struct device *hwmon_dev;
+ struct mutex lock;
+
+ u16 REG_CONFIG;
+ u16 REG_VBAT;
+
+ const s8 *ALARM_BITS;
+
+ const u16 *REG_VIN;
+ const u16 *REG_IN_MINMAX[2];
+
+ const u16 *REG_ALARM;
+
+ struct mutex update_lock;
+ bool valid; /* true if following fields are valid */
+ unsigned long last_updated; /* In jiffies */
+
+ /* Register values */
+ u8 bank; /* current register bank */
+ u8 in_num; /* number of in inputs we have */
+ u8 in[15][3]; /* [0]=in, [1]=in_max, [2]=in_min */
+
+ u64 alarms;
+
+ u8 vid;
+ u8 vrm;
+
+ u16 have_in;
+};
+
+struct nct6775_sio_data {
+ int sioreg;
+ enum kinds kind;
+};
+
+static bool is_word_sized(struct nct6775_data *data, u16 reg)
+{
+ switch (data->kind) {
+ case nct6775:
+ return (((reg & 0xff00) == 0x100 ||
+ (reg & 0xff00) == 0x200) &&
+ ((reg & 0x00ff) == 0x50 ||
+ (reg & 0x00ff) == 0x53 ||
+ (reg & 0x00ff) == 0x55)) ||
+ (reg & 0xfff0) == 0x630 ||
+ reg == 0x640 || reg == 0x642 ||
+ reg == 0x662 ||
+ ((reg & 0xfff0) == 0x650 && (reg & 0x000f) >= 0x06) ||
+ reg == 0x73 || reg == 0x75 || reg == 0x77;
+ case nct6776:
+ return (((reg & 0xff00) == 0x100 ||
+ (reg & 0xff00) == 0x200) &&
+ ((reg & 0x00ff) == 0x50 ||
+ (reg & 0x00ff) == 0x53 ||
+ (reg & 0x00ff) == 0x55)) ||
+ (reg & 0xfff0) == 0x630 ||
+ reg == 0x402 ||
+ reg == 0x640 || reg == 0x642 ||
+ ((reg & 0xfff0) == 0x650 && (reg & 0x000f) >= 0x06) ||
+ reg == 0x73 || reg == 0x75 || reg == 0x77;
+ case nct6779:
+ return reg == 0x150 || reg == 0x153 || reg == 0x155 ||
+ ((reg & 0xfff0) == 0x4b0 && (reg & 0x000f) < 0x09) ||
+ reg == 0x402 ||
+ reg == 0x63a || reg == 0x63c || reg == 0x63e ||
+ reg == 0x640 || reg == 0x642 ||
+ reg == 0x73 || reg == 0x75 || reg == 0x77 || reg == 0x79 ||
+ reg == 0x7b;
+ }
+ return false;
+}
+
+/*
+ * On older chips, only registers 0x50-0x5f are banked.
+ * On more recent chips, all registers are banked.
+ * Assume that is the case and set the bank number for each access.
+ * Cache the bank number so it only needs to be set if it changes.
+ */
+static inline void nct6775_set_bank(struct nct6775_data *data, u16 reg)
+{
+ u8 bank = reg >> 8;
+ if (data->bank != bank) {
+ outb_p(NCT6775_REG_BANK, data->addr + ADDR_REG_OFFSET);
+ outb_p(bank, data->addr + DATA_REG_OFFSET);
+ data->bank = bank;
+ }
+}
+
+static u16 nct6775_read_value(struct nct6775_data *data, u16 reg)
+{
+ int res, word_sized = is_word_sized(data, reg);
+
+ mutex_lock(&data->lock);
+
+ nct6775_set_bank(data, reg);
+ outb_p(reg & 0xff, data->addr + ADDR_REG_OFFSET);
+ res = inb_p(data->addr + DATA_REG_OFFSET);
+ if (word_sized) {
+ outb_p((reg & 0xff) + 1,
+ data->addr + ADDR_REG_OFFSET);
+ res = (res << 8) + inb_p(data->addr + DATA_REG_OFFSET);
+ }
+
+ mutex_unlock(&data->lock);
+ return res;
+}
+
+static int nct6775_write_value(struct nct6775_data *data, u16 reg, u16 value)
+{
+ int word_sized = is_word_sized(data, reg);
+
+ mutex_lock(&data->lock);
+
+ nct6775_set_bank(data, reg);
+ outb_p(reg & 0xff, data->addr + ADDR_REG_OFFSET);
+ if (word_sized) {
+ outb_p(value >> 8, data->addr + DATA_REG_OFFSET);
+ outb_p((reg & 0xff) + 1,
+ data->addr + ADDR_REG_OFFSET);
+ }
+ outb_p(value & 0xff, data->addr + DATA_REG_OFFSET);
+
+ mutex_unlock(&data->lock);
+ return 0;
+}
+
+static struct nct6775_data *nct6775_update_device(struct device *dev)
+{
+ struct nct6775_data *data = dev_get_drvdata(dev);
+ int i;
+
+ mutex_lock(&data->update_lock);
+
+ if (time_after(jiffies, data->last_updated + HZ + HZ/2)
+ || !data->valid) {
+ /* Measured voltages and limits */
+ for (i = 0; i < data->in_num; i++) {
+ if (!(data->have_in & (1 << i)))
+ continue;
+
+ data->in[i][0] = nct6775_read_value(data,
+ data->REG_VIN[i]);
+ data->in[i][1] = nct6775_read_value(data,
+ data->REG_IN_MINMAX[0][i]);
+ data->in[i][2] = nct6775_read_value(data,
+ data->REG_IN_MINMAX[1][i]);
+ }
+
+ data->alarms = 0;
+ for (i = 0; i < NUM_REG_ALARM; i++) {
+ u8 alarm;
+ if (!data->REG_ALARM[i])
+ continue;
+ alarm = nct6775_read_value(data, data->REG_ALARM[i]);
+ data->alarms |= ((u64)alarm) << (i << 3);
+ }
+
+ data->last_updated = jiffies;
+ data->valid = true;
+ }
+
+ mutex_unlock(&data->update_lock);
+ return data;
+}
+
+/*
+ * Sysfs callback functions
+ */
+static ssize_t
+show_in_reg(struct device *dev, struct device_attribute *attr, char *buf)
+{
+ struct nct6775_data *data = nct6775_update_device(dev);
+ struct sensor_device_attribute_2 *sattr = to_sensor_dev_attr_2(attr);
+ int nr = sattr->nr;
+ int index = sattr->index;
+ return sprintf(buf, "%ld\n", in_from_reg(data->in[nr][index], nr));
+}
+
+static ssize_t
+store_in_reg(struct device *dev, struct device_attribute *attr, const char *buf,
+ size_t count)
+{
+ struct nct6775_data *data = dev_get_drvdata(dev);
+ struct sensor_device_attribute_2 *sattr = to_sensor_dev_attr_2(attr);
+ int nr = sattr->nr;
+ int index = sattr->index;
+ unsigned long val;
+ int err = kstrtoul(buf, 10, &val);
+ if (err < 0)
+ return err;
+ mutex_lock(&data->update_lock);
+ data->in[nr][index] = in_to_reg(val, nr);
+ nct6775_write_value(data, data->REG_IN_MINMAX[index-1][nr],
+ data->in[nr][index]);
+ mutex_unlock(&data->update_lock);
+ return count;
+}
+
+static ssize_t
+show_alarm(struct device *dev, struct device_attribute *attr, char *buf)
+{
+ struct nct6775_data *data = nct6775_update_device(dev);
+ struct sensor_device_attribute *sattr = to_sensor_dev_attr(attr);
+ int nr = data->ALARM_BITS[sattr->index];
+ return sprintf(buf, "%u\n",
+ (unsigned int)((data->alarms >> nr) & 0x01));
+}
+
+static SENSOR_DEVICE_ATTR_2(in0_input, S_IRUGO, show_in_reg, NULL, 0, 0);
+static SENSOR_DEVICE_ATTR_2(in1_input, S_IRUGO, show_in_reg, NULL, 1, 0);
+static SENSOR_DEVICE_ATTR_2(in2_input, S_IRUGO, show_in_reg, NULL, 2, 0);
+static SENSOR_DEVICE_ATTR_2(in3_input, S_IRUGO, show_in_reg, NULL, 3, 0);
+static SENSOR_DEVICE_ATTR_2(in4_input, S_IRUGO, show_in_reg, NULL, 4, 0);
+static SENSOR_DEVICE_ATTR_2(in5_input, S_IRUGO, show_in_reg, NULL, 5, 0);
+static SENSOR_DEVICE_ATTR_2(in6_input, S_IRUGO, show_in_reg, NULL, 6, 0);
+static SENSOR_DEVICE_ATTR_2(in7_input, S_IRUGO, show_in_reg, NULL, 7, 0);
+static SENSOR_DEVICE_ATTR_2(in8_input, S_IRUGO, show_in_reg, NULL, 8, 0);
+static SENSOR_DEVICE_ATTR_2(in9_input, S_IRUGO, show_in_reg, NULL, 9, 0);
+static SENSOR_DEVICE_ATTR_2(in10_input, S_IRUGO, show_in_reg, NULL, 10, 0);
+static SENSOR_DEVICE_ATTR_2(in11_input, S_IRUGO, show_in_reg, NULL, 11, 0);
+static SENSOR_DEVICE_ATTR_2(in12_input, S_IRUGO, show_in_reg, NULL, 12, 0);
+static SENSOR_DEVICE_ATTR_2(in13_input, S_IRUGO, show_in_reg, NULL, 13, 0);
+static SENSOR_DEVICE_ATTR_2(in14_input, S_IRUGO, show_in_reg, NULL, 14, 0);
+
+static SENSOR_DEVICE_ATTR(in0_alarm, S_IRUGO, show_alarm, NULL, 0);
+static SENSOR_DEVICE_ATTR(in1_alarm, S_IRUGO, show_alarm, NULL, 1);
+static SENSOR_DEVICE_ATTR(in2_alarm, S_IRUGO, show_alarm, NULL, 2);
+static SENSOR_DEVICE_ATTR(in3_alarm, S_IRUGO, show_alarm, NULL, 3);
+static SENSOR_DEVICE_ATTR(in4_alarm, S_IRUGO, show_alarm, NULL, 4);
+static SENSOR_DEVICE_ATTR(in5_alarm, S_IRUGO, show_alarm, NULL, 5);
+static SENSOR_DEVICE_ATTR(in6_alarm, S_IRUGO, show_alarm, NULL, 6);
+static SENSOR_DEVICE_ATTR(in7_alarm, S_IRUGO, show_alarm, NULL, 7);
+static SENSOR_DEVICE_ATTR(in8_alarm, S_IRUGO, show_alarm, NULL, 8);
+static SENSOR_DEVICE_ATTR(in9_alarm, S_IRUGO, show_alarm, NULL, 9);
+static SENSOR_DEVICE_ATTR(in10_alarm, S_IRUGO, show_alarm, NULL, 10);
+static SENSOR_DEVICE_ATTR(in11_alarm, S_IRUGO, show_alarm, NULL, 11);
+static SENSOR_DEVICE_ATTR(in12_alarm, S_IRUGO, show_alarm, NULL, 12);
+static SENSOR_DEVICE_ATTR(in13_alarm, S_IRUGO, show_alarm, NULL, 13);
+static SENSOR_DEVICE_ATTR(in14_alarm, S_IRUGO, show_alarm, NULL, 14);
+
+static SENSOR_DEVICE_ATTR_2(in0_min, S_IWUSR | S_IRUGO, show_in_reg,
+ store_in_reg, 0, 1);
+static SENSOR_DEVICE_ATTR_2(in1_min, S_IWUSR | S_IRUGO, show_in_reg,
+ store_in_reg, 1, 1);
+static SENSOR_DEVICE_ATTR_2(in2_min, S_IWUSR | S_IRUGO, show_in_reg,
+ store_in_reg, 2, 1);
+static SENSOR_DEVICE_ATTR_2(in3_min, S_IWUSR | S_IRUGO, show_in_reg,
+ store_in_reg, 3, 1);
+static SENSOR_DEVICE_ATTR_2(in4_min, S_IWUSR | S_IRUGO, show_in_reg,
+ store_in_reg, 4, 1);
+static SENSOR_DEVICE_ATTR_2(in5_min, S_IWUSR | S_IRUGO, show_in_reg,
+ store_in_reg, 5, 1);
+static SENSOR_DEVICE_ATTR_2(in6_min, S_IWUSR | S_IRUGO, show_in_reg,
+ store_in_reg, 6, 1);
+static SENSOR_DEVICE_ATTR_2(in7_min, S_IWUSR | S_IRUGO, show_in_reg,
+ store_in_reg, 7, 1);
+static SENSOR_DEVICE_ATTR_2(in8_min, S_IWUSR | S_IRUGO, show_in_reg,
+ store_in_reg, 8, 1);
+static SENSOR_DEVICE_ATTR_2(in9_min, S_IWUSR | S_IRUGO, show_in_reg,
+ store_in_reg, 9, 1);
+static SENSOR_DEVICE_ATTR_2(in10_min, S_IWUSR | S_IRUGO, show_in_reg,
+ store_in_reg, 10, 1);
+static SENSOR_DEVICE_ATTR_2(in11_min, S_IWUSR | S_IRUGO, show_in_reg,
+ store_in_reg, 11, 1);
+static SENSOR_DEVICE_ATTR_2(in12_min, S_IWUSR | S_IRUGO, show_in_reg,
+ store_in_reg, 12, 1);
+static SENSOR_DEVICE_ATTR_2(in13_min, S_IWUSR | S_IRUGO, show_in_reg,
+ store_in_reg, 13, 1);
+static SENSOR_DEVICE_ATTR_2(in14_min, S_IWUSR | S_IRUGO, show_in_reg,
+ store_in_reg, 14, 1);
+
+static SENSOR_DEVICE_ATTR_2(in0_max, S_IWUSR | S_IRUGO, show_in_reg,
+ store_in_reg, 0, 2);
+static SENSOR_DEVICE_ATTR_2(in1_max, S_IWUSR | S_IRUGO, show_in_reg,
+ store_in_reg, 1, 2);
+static SENSOR_DEVICE_ATTR_2(in2_max, S_IWUSR | S_IRUGO, show_in_reg,
+ store_in_reg, 2, 2);
+static SENSOR_DEVICE_ATTR_2(in3_max, S_IWUSR | S_IRUGO, show_in_reg,
+ store_in_reg, 3, 2);
+static SENSOR_DEVICE_ATTR_2(in4_max, S_IWUSR | S_IRUGO, show_in_reg,
+ store_in_reg, 4, 2);
+static SENSOR_DEVICE_ATTR_2(in5_max, S_IWUSR | S_IRUGO, show_in_reg,
+ store_in_reg, 5, 2);
+static SENSOR_DEVICE_ATTR_2(in6_max, S_IWUSR | S_IRUGO, show_in_reg,
+ store_in_reg, 6, 2);
+static SENSOR_DEVICE_ATTR_2(in7_max, S_IWUSR | S_IRUGO, show_in_reg,
+ store_in_reg, 7, 2);
+static SENSOR_DEVICE_ATTR_2(in8_max, S_IWUSR | S_IRUGO, show_in_reg,
+ store_in_reg, 8, 2);
+static SENSOR_DEVICE_ATTR_2(in9_max, S_IWUSR | S_IRUGO, show_in_reg,
+ store_in_reg, 9, 2);
+static SENSOR_DEVICE_ATTR_2(in10_max, S_IWUSR | S_IRUGO, show_in_reg,
+ store_in_reg, 10, 2);
+static SENSOR_DEVICE_ATTR_2(in11_max, S_IWUSR | S_IRUGO, show_in_reg,
+ store_in_reg, 11, 2);
+static SENSOR_DEVICE_ATTR_2(in12_max, S_IWUSR | S_IRUGO, show_in_reg,
+ store_in_reg, 12, 2);
+static SENSOR_DEVICE_ATTR_2(in13_max, S_IWUSR | S_IRUGO, show_in_reg,
+ store_in_reg, 13, 2);
+static SENSOR_DEVICE_ATTR_2(in14_max, S_IWUSR | S_IRUGO, show_in_reg,
+ store_in_reg, 14, 2);
+
+static struct attribute *nct6775_attributes_in[15][5] = {
+ {
+ &sensor_dev_attr_in0_input.dev_attr.attr,
+ &sensor_dev_attr_in0_min.dev_attr.attr,
+ &sensor_dev_attr_in0_max.dev_attr.attr,
+ &sensor_dev_attr_in0_alarm.dev_attr.attr,
+ NULL
+ },
+ {
+ &sensor_dev_attr_in1_input.dev_attr.attr,
+ &sensor_dev_attr_in1_min.dev_attr.attr,
+ &sensor_dev_attr_in1_max.dev_attr.attr,
+ &sensor_dev_attr_in1_alarm.dev_attr.attr,
+ NULL
+ },
+ {
+ &sensor_dev_attr_in2_input.dev_attr.attr,
+ &sensor_dev_attr_in2_min.dev_attr.attr,
+ &sensor_dev_attr_in2_max.dev_attr.attr,
+ &sensor_dev_attr_in2_alarm.dev_attr.attr,
+ NULL
+ },
+ {
+ &sensor_dev_attr_in3_input.dev_attr.attr,
+ &sensor_dev_attr_in3_min.dev_attr.attr,
+ &sensor_dev_attr_in3_max.dev_attr.attr,
+ &sensor_dev_attr_in3_alarm.dev_attr.attr,
+ NULL
+ },
+ {
+ &sensor_dev_attr_in4_input.dev_attr.attr,
+ &sensor_dev_attr_in4_min.dev_attr.attr,
+ &sensor_dev_attr_in4_max.dev_attr.attr,
+ &sensor_dev_attr_in4_alarm.dev_attr.attr,
+ NULL
+ },
+ {
+ &sensor_dev_attr_in5_input.dev_attr.attr,
+ &sensor_dev_attr_in5_min.dev_attr.attr,
+ &sensor_dev_attr_in5_max.dev_attr.attr,
+ &sensor_dev_attr_in5_alarm.dev_attr.attr,
+ NULL
+ },
+ {
+ &sensor_dev_attr_in6_input.dev_attr.attr,
+ &sensor_dev_attr_in6_min.dev_attr.attr,
+ &sensor_dev_attr_in6_max.dev_attr.attr,
+ &sensor_dev_attr_in6_alarm.dev_attr.attr,
+ NULL
+ },
+ {
+ &sensor_dev_attr_in7_input.dev_attr.attr,
+ &sensor_dev_attr_in7_min.dev_attr.attr,
+ &sensor_dev_attr_in7_max.dev_attr.attr,
+ &sensor_dev_attr_in7_alarm.dev_attr.attr,
+ NULL
+ },
+ {
+ &sensor_dev_attr_in8_input.dev_attr.attr,
+ &sensor_dev_attr_in8_min.dev_attr.attr,
+ &sensor_dev_attr_in8_max.dev_attr.attr,
+ &sensor_dev_attr_in8_alarm.dev_attr.attr,
+ NULL
+ },
+ {
+ &sensor_dev_attr_in9_input.dev_attr.attr,
+ &sensor_dev_attr_in9_min.dev_attr.attr,
+ &sensor_dev_attr_in9_max.dev_attr.attr,
+ &sensor_dev_attr_in9_alarm.dev_attr.attr,
+ NULL
+ },
+ {
+ &sensor_dev_attr_in10_input.dev_attr.attr,
+ &sensor_dev_attr_in10_min.dev_attr.attr,
+ &sensor_dev_attr_in10_max.dev_attr.attr,
+ &sensor_dev_attr_in10_alarm.dev_attr.attr,
+ NULL
+ },
+ {
+ &sensor_dev_attr_in11_input.dev_attr.attr,
+ &sensor_dev_attr_in11_min.dev_attr.attr,
+ &sensor_dev_attr_in11_max.dev_attr.attr,
+ &sensor_dev_attr_in11_alarm.dev_attr.attr,
+ NULL
+ },
+ {
+ &sensor_dev_attr_in12_input.dev_attr.attr,
+ &sensor_dev_attr_in12_min.dev_attr.attr,
+ &sensor_dev_attr_in12_max.dev_attr.attr,
+ &sensor_dev_attr_in12_alarm.dev_attr.attr,
+ NULL
+ },
+ {
+ &sensor_dev_attr_in13_input.dev_attr.attr,
+ &sensor_dev_attr_in13_min.dev_attr.attr,
+ &sensor_dev_attr_in13_max.dev_attr.attr,
+ &sensor_dev_attr_in13_alarm.dev_attr.attr,
+ NULL
+ },
+ {
+ &sensor_dev_attr_in14_input.dev_attr.attr,
+ &sensor_dev_attr_in14_min.dev_attr.attr,
+ &sensor_dev_attr_in14_max.dev_attr.attr,
+ &sensor_dev_attr_in14_alarm.dev_attr.attr,
+ NULL
+ },
+};
+
+static const struct attribute_group nct6775_group_in[15] = {
+ { .attrs = nct6775_attributes_in[0] },
+ { .attrs = nct6775_attributes_in[1] },
+ { .attrs = nct6775_attributes_in[2] },
+ { .attrs = nct6775_attributes_in[3] },
+ { .attrs = nct6775_attributes_in[4] },
+ { .attrs = nct6775_attributes_in[5] },
+ { .attrs = nct6775_attributes_in[6] },
+ { .attrs = nct6775_attributes_in[7] },
+ { .attrs = nct6775_attributes_in[8] },
+ { .attrs = nct6775_attributes_in[9] },
+ { .attrs = nct6775_attributes_in[10] },
+ { .attrs = nct6775_attributes_in[11] },
+ { .attrs = nct6775_attributes_in[12] },
+ { .attrs = nct6775_attributes_in[13] },
+ { .attrs = nct6775_attributes_in[14] },
+};
+
+static ssize_t
+show_name(struct device *dev, struct device_attribute *attr, char *buf)
+{
+ struct nct6775_data *data = dev_get_drvdata(dev);
+
+ return sprintf(buf, "%s\n", data->name);
+}
+
+static DEVICE_ATTR(name, S_IRUGO, show_name, NULL);
+
+static ssize_t
+show_vid(struct device *dev, struct device_attribute *attr, char *buf)
+{
+ struct nct6775_data *data = dev_get_drvdata(dev);
+ return sprintf(buf, "%d\n", vid_from_reg(data->vid, data->vrm));
+}
+
+static DEVICE_ATTR(cpu0_vid, S_IRUGO, show_vid, NULL);
+
+/*
+ * Driver and device management
+ */
+
+static void nct6775_device_remove_files(struct device *dev)
+{
+ /*
+ * some entries in the following arrays may not have been used in
+ * device_create_file(), but device_remove_file() will ignore them
+ */
+ int i;
+ struct nct6775_data *data = dev_get_drvdata(dev);
+
+ for (i = 0; i < data->in_num; i++)
+ sysfs_remove_group(&dev->kobj, &nct6775_group_in[i]);
+
+ device_remove_file(dev, &dev_attr_name);
+ device_remove_file(dev, &dev_attr_cpu0_vid);
+}
+
+/* Get the monitoring functions started */
+static inline void nct6775_init_device(struct nct6775_data *data)
+{
+ u8 tmp;
+
+ /* Start monitoring if needed */
+ if (data->REG_CONFIG) {
+ tmp = nct6775_read_value(data, data->REG_CONFIG);
+ if (!(tmp & 0x01))
+ nct6775_write_value(data, data->REG_CONFIG, tmp | 0x01);
+ }
+
+ /* Enable VBAT monitoring if needed */
+ tmp = nct6775_read_value(data, data->REG_VBAT);
+ if (!(tmp & 0x01))
+ nct6775_write_value(data, data->REG_VBAT, tmp | 0x01);
+}
+
+static int nct6775_probe(struct platform_device *pdev)
+{
+ struct device *dev = &pdev->dev;
+ struct nct6775_sio_data *sio_data = dev->platform_data;
+ struct nct6775_data *data;
+ struct resource *res;
+ int i, err = 0;
+
+ res = platform_get_resource(pdev, IORESOURCE_IO, 0);
+ if (!devm_request_region(&pdev->dev, res->start, IOREGION_LENGTH,
+ DRVNAME))
+ return -EBUSY;
+
+ data = devm_kzalloc(&pdev->dev, sizeof(struct nct6775_data),
+ GFP_KERNEL);
+ if (!data)
+ return -ENOMEM;
+
+ data->kind = sio_data->kind;
+ data->addr = res->start;
+ mutex_init(&data->lock);
+ mutex_init(&data->update_lock);
+ data->name = nct6775_device_names[data->kind];
+ data->bank = 0xff; /* Force initial bank selection */
+ platform_set_drvdata(pdev, data);
+
+ switch (data->kind) {
+ case nct6775:
+ data->in_num = 9;
+
+ data->ALARM_BITS = NCT6775_ALARM_BITS;
+
+ data->REG_CONFIG = NCT6775_REG_CONFIG;
+ data->REG_VBAT = NCT6775_REG_VBAT;
+ data->REG_VIN = NCT6775_REG_IN;
+ data->REG_IN_MINMAX[0] = NCT6775_REG_IN_MIN;
+ data->REG_IN_MINMAX[1] = NCT6775_REG_IN_MAX;
+ data->REG_ALARM = NCT6775_REG_ALARM;
+ break;
+ case nct6776:
+ data->in_num = 9;
+
+ data->ALARM_BITS = NCT6776_ALARM_BITS;
+
+ data->REG_CONFIG = NCT6775_REG_CONFIG;
+ data->REG_VBAT = NCT6775_REG_VBAT;
+ data->REG_VIN = NCT6775_REG_IN;
+ data->REG_IN_MINMAX[0] = NCT6775_REG_IN_MIN;
+ data->REG_IN_MINMAX[1] = NCT6775_REG_IN_MAX;
+ data->REG_ALARM = NCT6775_REG_ALARM;
+ break;
+ case nct6779:
+ data->in_num = 15;
+
+ data->ALARM_BITS = NCT6779_ALARM_BITS;
+
+ data->REG_CONFIG = NCT6775_REG_CONFIG;
+ data->REG_VBAT = NCT6775_REG_VBAT;
+ data->REG_VIN = NCT6779_REG_IN;
+ data->REG_IN_MINMAX[0] = NCT6775_REG_IN_MIN;
+ data->REG_IN_MINMAX[1] = NCT6775_REG_IN_MAX;
+ data->REG_ALARM = NCT6779_REG_ALARM;
+ break;
+ default:
+ return -ENODEV;
+ }
+ data->have_in = (1 << data->in_num) - 1;
+
+ /* Initialize the chip */
+ nct6775_init_device(data);
+
+ data->vrm = vid_which_vrm();
+ err = superio_enter(sio_data->sioreg);
+ if (err)
+ return err;
+
+ /*
+ * Read VID value
+ * We can get the VID input values directly at logical device D 0xe3.
+ */
+ superio_select(sio_data->sioreg, NCT6775_LD_VID);
+ data->vid = superio_inb(sio_data->sioreg, 0xe3);
+ superio_exit(sio_data->sioreg);
+
+ err = device_create_file(dev, &dev_attr_cpu0_vid);
+ if (err)
+ return err;
+
+ for (i = 0; i < data->in_num; i++) {
+ if (!(data->have_in & (1 << i)))
+ continue;
+ err = sysfs_create_group(&dev->kobj, &nct6775_group_in[i]);
+ if (err)
+ goto exit_remove;
+ }
+
+ err = device_create_file(dev, &dev_attr_name);
+ if (err)
+ goto exit_remove;
+
+ data->hwmon_dev = hwmon_device_register(dev);
+ if (IS_ERR(data->hwmon_dev)) {
+ err = PTR_ERR(data->hwmon_dev);
+ goto exit_remove;
+ }
+
+ return 0;
+
+exit_remove:
+ nct6775_device_remove_files(dev);
+ return err;
+}
+
+static int nct6775_remove(struct platform_device *pdev)
+{
+ struct nct6775_data *data = platform_get_drvdata(pdev);
+
+ hwmon_device_unregister(data->hwmon_dev);
+ nct6775_device_remove_files(&pdev->dev);
+
+ return 0;
+}
+
+static struct platform_driver nct6775_driver = {
+ .driver = {
+ .owner = THIS_MODULE,
+ .name = DRVNAME,
+ },
+ .probe = nct6775_probe,
+ .remove = nct6775_remove,
+};
+
+/* nct6775_find() looks for a '627 in the Super-I/O config space */
+static int __init nct6775_find(int sioaddr, unsigned short *addr,
+ struct nct6775_sio_data *sio_data)
+{
+ static const char sio_name_NCT6775[] __initconst = "NCT6775F";
+ static const char sio_name_NCT6776[] __initconst = "NCT6776F";
+ static const char sio_name_NCT6779[] __initconst = "NCT6779D";
+
+ u16 val;
+ const char *sio_name;
+ int err;
+
+ err = superio_enter(sioaddr);
+ if (err)
+ return err;
+
+ if (force_id)
+ val = force_id;
+ else
+ val = (superio_inb(sioaddr, SIO_REG_DEVID) << 8)
+ | superio_inb(sioaddr, SIO_REG_DEVID + 1);
+ switch (val & SIO_ID_MASK) {
+ case SIO_NCT6775_ID:
+ sio_data->kind = nct6775;
+ sio_name = sio_name_NCT6775;
+ break;
+ case SIO_NCT6776_ID:
+ sio_data->kind = nct6776;
+ sio_name = sio_name_NCT6776;
+ break;
+ case SIO_NCT6779_ID:
+ sio_data->kind = nct6779;
+ sio_name = sio_name_NCT6779;
+ break;
+ default:
+ if (val != 0xffff)
+ pr_debug("unsupported chip ID: 0x%04x\n", val);
+ superio_exit(sioaddr);
+ return -ENODEV;
+ }
+
+ /* We have a known chip, find the HWM I/O address */
+ superio_select(sioaddr, NCT6775_LD_HWM);
+ val = (superio_inb(sioaddr, SIO_REG_ADDR) << 8)
+ | superio_inb(sioaddr, SIO_REG_ADDR + 1);
+ *addr = val & IOREGION_ALIGNMENT;
+ if (*addr == 0) {
+ pr_err("Refusing to enable a Super-I/O device with a base I/O port 0\n");
+ superio_exit(sioaddr);
+ return -ENODEV;
+ }
+
+ /* Activate logical device if needed */
+ val = superio_inb(sioaddr, SIO_REG_ENABLE);
+ if (!(val & 0x01)) {
+ pr_warn("Forcibly enabling Super-I/O. Sensor is probably unusable.\n");
+ superio_outb(sioaddr, SIO_REG_ENABLE, val | 0x01);
+ }
+
+ superio_exit(sioaddr);
+ pr_info("Found %s chip at %#x\n", sio_name, *addr);
+ sio_data->sioreg = sioaddr;
+
+ return 0;
+}
+
+/*
+ * when Super-I/O functions move to a separate file, the Super-I/O
+ * bus will manage the lifetime of the device and this module will only keep
+ * track of the nct6775 driver. But since we platform_device_alloc(), we
+ * must keep track of the device
+ */
+static struct platform_device *pdev;
+
+static int __init sensors_nct6775_init(void)
+{
+ int err;
+ unsigned short address;
+ struct resource res;
+ struct nct6775_sio_data sio_data;
+
+ /*
+ * initialize sio_data->kind and sio_data->sioreg.
+ *
+ * when Super-I/O functions move to a separate file, the Super-I/O
+ * driver will probe 0x2e and 0x4e and auto-detect the presence of a
+ * nct6775 hardware monitor, and call probe()
+ */
+ if (nct6775_find(0x2e, &address, &sio_data) &&
+ nct6775_find(0x4e, &address, &sio_data))
+ return -ENODEV;
+
+ err = platform_driver_register(&nct6775_driver);
+ if (err)
+ goto exit;
+
+ pdev = platform_device_alloc(DRVNAME, address);
+ if (!pdev) {
+ err = -ENOMEM;
+ pr_err("Device allocation failed\n");
+ goto exit_unregister;
+ }
+
+ err = platform_device_add_data(pdev, &sio_data,
+ sizeof(struct nct6775_sio_data));
+ if (err) {
+ pr_err("Platform data allocation failed\n");
+ goto exit_device_put;
+ }
+
+ memset(&res, 0, sizeof(res));
+ res.name = DRVNAME;
+ res.start = address + IOREGION_OFFSET;
+ res.end = address + IOREGION_OFFSET + IOREGION_LENGTH - 1;
+ res.flags = IORESOURCE_IO;
+
+ err = acpi_check_resource_conflict(&res);
+ if (err)
+ goto exit_device_put;
+
+ err = platform_device_add_resources(pdev, &res, 1);
+ if (err) {
+ pr_err("Device resource addition failed (%d)\n", err);
+ goto exit_device_put;
+ }
+
+ /* platform_device_add calls probe() */
+ err = platform_device_add(pdev);
+ if (err) {
+ pr_err("Device addition failed (%d)\n", err);
+ goto exit_device_put;
+ }
+
+ return 0;
+
+exit_device_put:
+ platform_device_put(pdev);
+exit_unregister:
+ platform_driver_unregister(&nct6775_driver);
+exit:
+ return err;
+}
+
+static void __exit sensors_nct6775_exit(void)
+{
+ platform_device_unregister(pdev);
+ platform_driver_unregister(&nct6775_driver);
+}
+
+MODULE_AUTHOR("Guenter Roeck <linux@xxxxxxxxxxxx>");
+MODULE_DESCRIPTION("NCT6775F/NCT6776F/NCT6779D driver");
+MODULE_LICENSE("GPL");
+
+module_init(sensors_nct6775_init);
+module_exit(sensors_nct6775_exit);
--
1.7.9.7
_______________________________________________
lm-sensors mailing list
lm-sensors@xxxxxxxxxxxxxx
http://lists.lm-sensors.org/mailman/listinfo/lm-sensors
