> -----Original Message----- > From: Guenter Roeck [mailto:linux@xxxxxxxxxxxx] > Sent: Monday, October 01, 2012 12:19 PM > To: Bruce Parker > Cc: lm-sensors@xxxxxxxxxxxxxx > Subject: Re: How to use SC18IS602 driver ? > > On Mon, Oct 01, 2012 at 09:03:15AM -0500, Bruce Parker wrote: > > [ ... ] > > > > > Ok...got i2cdetect installed and below is result: > > # i2cdetect 0 > > WARNING! This program can confuse your I2C bus, cause data loss and > > worse! > > I will probe file /dev/i2c-0. > > I will probe address range 0x03-0x77. > > Continue? [Y/n] y > > 0 1 2 3 4 5 6 7 8 9 a b c d e f > > 00: -- -- -- -- -- -- -- -- -- -- -- -- -- > > 10: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- > > 20: UU UU UU UU UU UU UU UU UU -- -- -- -- -- -- -- > > 30: -- 31 -- -- -- -- -- UU -- -- -- -- -- -- -- -- > > 40: -- -- -- -- -- -- -- -- -- -- -- -- UU -- -- -- > > 50: UU UU UU UU UU UU UU -- -- -- -- -- -- -- -- -- > > 60: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- > > 70: -- -- -- -- -- -- -- -- > > I2C-SPI bridge is at addr 28, so it appears to be detected. > > > > Below is my entry in device tree, but I do not see anything > special in > > /dev/mtd* > > spi: spi@28 { > > compatible = > "nxp,sc18is602"; > > #address-cells = <1>; > > #size-cells = <0>; > > reg = <0x28>; > > m25p80@0 { > > > #address-cells = <1>; > > #size-cells = <1>; > > compatible = > > "fsl,espi-flash"; > > linux,modalias = > > "m25p80"; > > spi-max-frequency = > > <25000000>; > > modal = "s25sl064a"; > > reg = <0>; > > mode = <0>; > > > > partition@0 { > > reg = <0x0 > > 0x00080000>; > > label = "Test > > Image"; > > read-only; > > }; > > }; > > }; > > I don't know much about devicetree instantiation, but the one > example I found > for m25p80 looks a bit different and much simpler. > > flash: m25p80@0 { > compatible = "sst,sst25vf016b"; > spi-max-frequency = <20000000>; > reg = <0>; > }; > Ok, tried your example in my device tree and it definitely changed something. Unfortunately, the kernel crashed during booting as shown below. But I guess it does imply it was trying to instantiate the device, where previous device tree didn't seem to be doing anything for the SPI. Do you know how I could try to instantiate the device outside of a device tree? Unable to handle kernel paging request for instruction fetch Faulting instruction address: 0x00000000 Oops: Kernel access of bad area, sig: 11 [#1] PowerPC 44x Platform Modules linked in: NIP: 00000000 LR: 8022dcb4 CTR: 00000000 REGS: 9f8a5ec0 TRAP: 0400 Not tainted (3.4.0-tanisys-sx2-25227) MSR: 00029000 <CE,EE,ME> CR: 22000022 XER: 20000000 TASK = ef8fd5e0[1039] 'spi0' THREAD: 9f8a4000 GPR00: 00000000 9f8a5f70 ef8fd5e0 ef8cf400 ef8fd5e0 ffff5762 ffffffff ffd23940 GPR08: 00000001 00000000 ef8cf524 ef8cf524 22002022 10220170 7fff2500 7ffe122c GPR16: 7ffe1250 00000000 7ffed388 034f2c0f 03000040 7ff31f70 80000010 0000000e GPR24: 00000000 7ff31e90 00000e80 80047c38 ef8cf504 00029000 ef8cf504 ef8cf400 NIP [00000000] (null) LR [8022dcb4] spi_pump_messages+0x108/0x160 Call Trace: [9f8a5f70] [7ff31e90] 0x7ff31e90 (unreliable) [9f8a5f90] [80047ba0] kthread_worker_fn+0x98/0x130 [9f8a5fb0] [80047cbc] kthread+0x84/0x88 [9f8a5ff0] [8000b390] kernel_thread+0x4c/0x68 Instruction dump: XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX ---[ end trace f360c06729bfcc7f ]--- > > > > > > # ls /dev/mtd* > > /dev/mtd0 /dev/mtd6 /dev/mtdblock2 /dev/mtdr12 > > /dev/mtd1 /dev/mtd7 /dev/mtdblock3 /dev/mtdr13 > > /dev/mtd10 /dev/mtd8 /dev/mtdblock4 /dev/mtdr14 > > /dev/mtd11 /dev/mtd9 /dev/mtdblock5 /dev/mtdr15 > > /dev/mtd12 /dev/mtdblock0 /dev/mtdblock6 /dev/mtdr2 > > /dev/mtd13 /dev/mtdblock1 /dev/mtdblock7 /dev/mtdr3 > > /dev/mtd14 /dev/mtdblock10 /dev/mtdblock8 /dev/mtdr4 > > /dev/mtd15 /dev/mtdblock11 /dev/mtdblock9 /dev/mtdr5 > > /dev/mtd2 /dev/mtdblock12 /dev/mtdr0 /dev/mtdr6 > > /dev/mtd3 /dev/mtdblock13 /dev/mtdr1 /dev/mtdr7 > > /dev/mtd4 /dev/mtdblock14 /dev/mtdr10 /dev/mtdr8 > > /dev/mtd5 /dev/mtdblock15 /dev/mtdr11 /dev/mtdr9 > > > Since you do see a whole lot of mtd devices, did you try to > access any of those ? > > Also, what is the output of /proc/mtd ? That should give you > a mapping from > the partition label to the actual mtd device if the partition > was created. > > Thanks, > Guenter > Forgot to include this before but /proc/mtd shows nothing even though all those files are there. # cat /proc/mtd dev: size erasesize name # Bruce... _______________________________________________ lm-sensors mailing list lm-sensors@xxxxxxxxxxxxxx http://lists.lm-sensors.org/mailman/listinfo/lm-sensors
