The MAX197 is an A/D converter, made by Maxim. This driver currently
supports the MAX197, and MAX199. They are both 8-Channel, Multi-Range,
5V, 12-Bit DAS with 8+4 Bus Interface and Fault Protection.
The available ranges for the MAX197 are {0,-5V} to 5V, and {0,-10V} to
10V, while they are {0,-2V} to 2V, and {0,-4V} to 4V on the MAX199.
Signed-off-by: Vivien Didelot <vivien.didelot@xxxxxxxxxxxxxxxxxxxx>
---
Documentation/hwmon/max197 | 60 ++++++
drivers/hwmon/Kconfig | 9 +
drivers/hwmon/Makefile | 1 +
drivers/hwmon/max197.c | 377 +++++++++++++++++++++++++++++++++++
include/linux/platform_data/max197.h | 21 ++
5 files changed, 468 insertions(+)
create mode 100644 Documentation/hwmon/max197
create mode 100644 drivers/hwmon/max197.c
create mode 100644 include/linux/platform_data/max197.h
diff --git a/Documentation/hwmon/max197 b/Documentation/hwmon/max197
new file mode 100644
index 0000000..8d89b90
--- /dev/null
+++ b/Documentation/hwmon/max197
@@ -0,0 +1,60 @@
+Maxim MAX197 driver
+===================
+
+Author:
+ * Vivien Didelot <vivien.didelot@xxxxxxxxxxxxxxxxxxxx>
+
+Supported chips:
+ * Maxim MAX197
+ Prefix: 'max197'
+ Datasheet: http://datasheets.maxim-ic.com/en/ds/MAX197.pdf
+
+ * Maxim MAX199
+ Prefix: 'max199'
+ Datasheet: http://datasheets.maxim-ic.com/en/ds/MAX199.pdf
+
+Description
+-----------
+
+The A/D converters MAX197, and MAX199 are both 8-Channel, Multi-Range, 5V,
+12-Bit DAS with 8+4 Bus Interface and Fault Protection.
+
+The available ranges for the MAX197 are {0,-5V} to 5V, and {0,-10V} to 10V,
+while they are {0,-2V} to 2V, and {0,-4V} to 4V on the MAX199.
+
+Platform data
+-------------
+
+The MAX197 platform data (defined in linux/platform_data/max197.h) should be
+filled with a pointer to a conversion function, defined like:
+
+ int convert(u8 ctrl);
+
+ctrl is the control byte to write to start a new conversion.
+On success, the function must return the 12-bit raw value read from the chip,
+or a negative error code otherwise.
+
+Control byte format:
+
+Bit Name Description
+7,6 PD1,PD0 Clock and Power-Down modes
+5 ACQMOD Internal or External Controlled Acquisition
+4 RNG Full-scale voltage magnitude at the input
+3 BIP Unipolar or Bipolar conversion mode
+2,1,0 A2,A1,A0 Channel
+
+Sysfs interface
+---------------
+
+* in[0-7]_input: The conversion value for the corresponding channel.
+ RO
+
+* in[0-7]_min: The lower limit (in mV) for the corresponding channel.
+ For the MAX197, it will be adjusted to -10000, -5000, or 0.
+ For the MAX199, it will be adjusted to -4000, -2000, or 0.
+ RW
+
+* in[0-7]_max: The higher limit (in mV) for the corresponding channel.
+ For the MAX197, it will be adjusted to 0, 5000, or 10000.
+ For the MAX199, it will be adjusted to 0, 2000, or 4000.
+ RW
diff --git a/drivers/hwmon/Kconfig b/drivers/hwmon/Kconfig
index b0a2e4c..2196869 100644
--- a/drivers/hwmon/Kconfig
+++ b/drivers/hwmon/Kconfig
@@ -803,6 +803,15 @@ config SENSORS_MAX1668
This driver can also be built as a module. If so, the module
will be called max1668.
+config SENSORS_MAX197
+ tristate "Maxim MAX197 and compatibles"
+ help
+ Support for the Maxim MAX197 A/D converter.
+ Support will include, but not be limited to, MAX197, and MAX199.
+
+ This driver can also be built as a module. If so, the module
+ will be called max197.
+
config SENSORS_MAX6639
tristate "Maxim MAX6639 sensor chip"
depends on I2C && EXPERIMENTAL
diff --git a/drivers/hwmon/Makefile b/drivers/hwmon/Makefile
index 7aa9811..1e8f690 100644
--- a/drivers/hwmon/Makefile
+++ b/drivers/hwmon/Makefile
@@ -94,6 +94,7 @@ obj-$(CONFIG_SENSORS_MAX1111) += max1111.o
obj-$(CONFIG_SENSORS_MAX16065) += max16065.o
obj-$(CONFIG_SENSORS_MAX1619) += max1619.o
obj-$(CONFIG_SENSORS_MAX1668) += max1668.o
+obj-$(CONFIG_SENSORS_MAX197) += max197.o
obj-$(CONFIG_SENSORS_MAX6639) += max6639.o
obj-$(CONFIG_SENSORS_MAX6642) += max6642.o
obj-$(CONFIG_SENSORS_MAX6650) += max6650.o
diff --git a/drivers/hwmon/max197.c b/drivers/hwmon/max197.c
new file mode 100644
index 0000000..e923385
--- /dev/null
+++ b/drivers/hwmon/max197.c
@@ -0,0 +1,377 @@
+/*
+ * Maxim MAX197 A/D Converter driver
+ *
+ * Copyright (c) 2012 Savoir-faire Linux Inc.
+ * Vivien Didelot <vivien.didelot@xxxxxxxxxxxxxxxxxxxx>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ * For further information, see the Documentation/hwmon/max197 file.
+ */
+
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/init.h>
+#include <linux/err.h>
+#include <linux/slab.h>
+#include <linux/mutex.h>
+#include <linux/device.h>
+#include <linux/sysfs.h>
+#include <linux/hwmon.h>
+#include <linux/hwmon-sysfs.h>
+#include <linux/platform_device.h>
+#include <linux/platform_data/max197.h>
+
+#define MAX199_LIMIT 4000 /* 4V */
+#define MAX197_LIMIT 10000 /* 10V */
+
+#define MAX197_NUM_CH 8 /* 8 Analog Input Channels */
+
+/* Control byte format */
+#define MAX197_BIP (1 << 3) /* Bipolarity */
+#define MAX197_RNG (1 << 4) /* Full range */
+
+#define MAX197_SCALE 12207 /* Scale coefficient for raw data */
+
+/**
+ * struct max197_chip - device instance specific data
+ * @pdata: Platform data.
+ * @hwmon_dev: The hwmon device.
+ * @lock: Read/Write mutex.
+ * @limit: Max range value (10V for MAX197, 4V for MAX199).
+ * @scale: Need to scale.
+ * @ctrl_bytes: Channels control byte.
+ */
+struct max197_chip {
+ struct max197_platform_data *pdata;
+ struct device *hwmon_dev;
+ struct mutex lock;
+ int limit;
+ bool scale;
+ u8 ctrl_bytes[MAX197_NUM_CH];
+};
+
+static inline void max197_set_unipolarity(struct max197_chip *chip, int channel)
+{
+ chip->ctrl_bytes[channel] &= ~MAX197_BIP;
+}
+
+static inline void max197_set_bipolarity(struct max197_chip *chip, int channel)
+{
+ chip->ctrl_bytes[channel] |= MAX197_BIP;
+}
+
+static inline void max197_set_half_range(struct max197_chip *chip, int channel)
+{
+ chip->ctrl_bytes[channel] &= ~MAX197_RNG;
+}
+
+static inline void max197_set_full_range(struct max197_chip *chip, int channel)
+{
+ chip->ctrl_bytes[channel] |= MAX197_RNG;
+}
+
+static inline bool max197_is_bipolar(struct max197_chip *chip, int channel)
+{
+ return chip->ctrl_bytes[channel] & MAX197_BIP;
+}
+
+static inline bool max197_is_full_range(struct max197_chip *chip, int channel)
+{
+ return chip->ctrl_bytes[channel] & MAX197_RNG;
+}
+
+/* Function called on read access on in{0,1,2,3,4,5,6,7}_{min,max} */
+static ssize_t max197_show_range(struct device *dev,
+ struct device_attribute *devattr, char *buf)
+{
+ struct max197_chip *chip = dev_get_drvdata(dev);
+ struct sensor_device_attribute_2 *attr = to_sensor_dev_attr_2(devattr);
+ int channel = attr->index;
+ bool is_min = attr->nr;
+ int range;
+
+ if (mutex_lock_interruptible(&chip->lock))
+ return -ERESTARTSYS;
+
+ range = max197_is_full_range(chip, channel) ?
+ chip->limit : chip->limit / 2;
+ if (is_min) {
+ if (max197_is_bipolar(chip, channel))
+ range = -range;
+ else
+ range = 0;
+ }
+
+ mutex_unlock(&chip->lock);
+
+ return sprintf(buf, "%d\n", range);
+}
+
+/* Function called on write access on in{0,1,2,3,4,5,6,7}_{min,max} */
+static ssize_t max197_store_range(struct device *dev,
+ struct device_attribute *devattr,
+ const char *buf, size_t count)
+{
+ struct max197_chip *chip = dev_get_drvdata(dev);
+ struct sensor_device_attribute_2 *attr = to_sensor_dev_attr_2(devattr);
+ int channel = attr->index;
+ bool is_min = attr->nr;
+ long value;
+ int half = chip->limit / 2;
+ int full = chip->limit;
+
+ if (kstrtol(buf, 10, &value))
+ return -EINVAL;
+
+ if (is_min) {
+ if (value <= -full)
+ value = -full;
+ else if (value < 0)
+ value = -half;
+ else
+ value = 0;
+ } else {
+ if (value >= full)
+ value = full;
+ else
+ value = half;
+ }
+
+ if (mutex_lock_interruptible(&chip->lock))
+ return -ERESTARTSYS;
+
+ if (value == 0) {
+ /* We can deduce only the polarity */
+ max197_set_unipolarity(chip, channel);
+ } else if (value == -half) {
+ max197_set_bipolarity(chip, channel);
+ max197_set_half_range(chip, channel);
+ } else if (value == -full) {
+ max197_set_bipolarity(chip, channel);
+ max197_set_full_range(chip, channel);
+ } else if (value == half) {
+ /* We can deduce only the range */
+ max197_set_half_range(chip, channel);
+ } else if (value == full) {
+ /* We can deduce only the range */
+ max197_set_full_range(chip, channel);
+ }
+
+ mutex_unlock(&chip->lock);
+
+ return count;
+}
+
+/* Function called on read access on in{0,1,2,3,4,5,6,7}_input */
+static ssize_t max197_show_input(struct device *dev,
+ struct device_attribute *devattr,
+ char *buf)
+{
+ struct max197_chip *chip = dev_get_drvdata(dev);
+ struct sensor_device_attribute *attr = to_sensor_dev_attr(devattr);
+ int channel = attr->index;
+ s32 value;
+ int ret;
+
+ if (mutex_lock_interruptible(&chip->lock))
+ return -ERESTARTSYS;
+
+ ret = chip->pdata->convert(chip->ctrl_bytes[channel]);
+ if (ret < 0) {
+ dev_err(dev, "conversion failed\n");
+ goto unlock;
+ }
+ value = ret;
+
+ /*
+ * Coefficient to apply on raw value.
+ * See Table 1. Full Scale and Zero Scale in the MAX197 datasheet.
+ */
+ if (chip->scale) {
+ value *= MAX197_SCALE;
+ if (max197_is_full_range(chip, channel))
+ value *= 2;
+ value /= 10000;
+ }
+
+ ret = sprintf(buf, "%d\n", value);
+
+unlock:
+ mutex_unlock(&chip->lock);
+ return ret;
+}
+
+static ssize_t max197_show_name(struct device *dev,
+ struct device_attribute *attr, char *buf)
+{
+ struct platform_device *pdev = to_platform_device(dev);
+ return sprintf(buf, "%s\n", pdev->name);
+}
+
+#define MAX197_SENSOR_DEVICE_ATTR_CH(chan) \
+ static SENSOR_DEVICE_ATTR(in##chan##_input, S_IRUGO, \
+ max197_show_input, NULL, chan); \
+ static SENSOR_DEVICE_ATTR_2(in##chan##_min, S_IRUGO | S_IWUSR, \
+ max197_show_range, \
+ max197_store_range, \
+ true, chan); \
+ static SENSOR_DEVICE_ATTR_2(in##chan##_max, S_IRUGO | S_IWUSR, \
+ max197_show_range, \
+ max197_store_range, \
+ false, chan)
+
+#define MAX197_SENSOR_DEV_ATTR_IN(chan) \
+ &sensor_dev_attr_in##chan##_input.dev_attr.attr, \
+ &sensor_dev_attr_in##chan##_max.dev_attr.attr, \
+ &sensor_dev_attr_in##chan##_min.dev_attr.attr
+
+static DEVICE_ATTR(name, S_IRUGO, max197_show_name, NULL);
+
+MAX197_SENSOR_DEVICE_ATTR_CH(0);
+MAX197_SENSOR_DEVICE_ATTR_CH(1);
+MAX197_SENSOR_DEVICE_ATTR_CH(2);
+MAX197_SENSOR_DEVICE_ATTR_CH(3);
+MAX197_SENSOR_DEVICE_ATTR_CH(4);
+MAX197_SENSOR_DEVICE_ATTR_CH(5);
+MAX197_SENSOR_DEVICE_ATTR_CH(6);
+MAX197_SENSOR_DEVICE_ATTR_CH(7);
+
+static const struct attribute_group max197_sysfs_group = {
+ .attrs = (struct attribute *[]) {
+ &dev_attr_name.attr,
+ MAX197_SENSOR_DEV_ATTR_IN(0),
+ MAX197_SENSOR_DEV_ATTR_IN(1),
+ MAX197_SENSOR_DEV_ATTR_IN(2),
+ MAX197_SENSOR_DEV_ATTR_IN(3),
+ MAX197_SENSOR_DEV_ATTR_IN(4),
+ MAX197_SENSOR_DEV_ATTR_IN(5),
+ MAX197_SENSOR_DEV_ATTR_IN(6),
+ MAX197_SENSOR_DEV_ATTR_IN(7),
+ NULL
+ }
+};
+
+static int __devinit max197_probe(struct platform_device *pdev)
+{
+ struct max197_chip *chip;
+ struct max197_platform_data *pdata;
+ int ch, ret;
+
+ if (pdev->dev.platform_data == NULL) {
+ dev_err(&pdev->dev, "no platform data supplied\n");
+ return -EINVAL;
+ }
+ pdata = pdev->dev.platform_data;
+
+ if (pdata->convert == NULL) {
+ dev_err(&pdev->dev, "no convert function supplied\n");
+ return -EINVAL;
+ }
+
+ chip = devm_kzalloc(&pdev->dev, sizeof(struct max197_chip), GFP_KERNEL);
+ if (!chip) {
+ dev_err(&pdev->dev, "devm_kzalloc failed\n");
+ return -ENOMEM;
+ }
+
+ chip->pdata = pdata;
+ mutex_init(&chip->lock);
+
+ if (strcmp("max197", pdev->name) == 0) {
+ chip->limit = MAX197_LIMIT;
+ chip->scale = true;
+ } else {
+ chip->limit = MAX199_LIMIT;
+ chip->scale = false;
+ }
+
+ for (ch = 0; ch < MAX197_NUM_CH; ch++)
+ chip->ctrl_bytes[ch] = (u8) ch;
+
+ platform_set_drvdata(pdev, chip);
+
+ ret = sysfs_create_group(&pdev->dev.kobj, &max197_sysfs_group);
+ if (ret) {
+ dev_err(&pdev->dev, "sysfs create group failed\n");
+ return ret;
+ }
+
+ chip->hwmon_dev = hwmon_device_register(&pdev->dev);
+ if (IS_ERR(chip->hwmon_dev)) {
+ ret = PTR_ERR(chip->hwmon_dev);
+ dev_err(&pdev->dev, "hwmon device register failed\n");
+ goto error;
+ }
+
+ return 0;
+
+error:
+ sysfs_remove_group(&pdev->dev.kobj, &max197_sysfs_group);
+ return ret;
+}
+
+static int __devexit max197_remove(struct platform_device *pdev)
+{
+ struct max197_chip *chip = platform_get_drvdata(pdev);
+
+ hwmon_device_unregister(chip->hwmon_dev);
+ sysfs_remove_group(&pdev->dev.kobj, &max197_sysfs_group);
+
+ return 0;
+}
+
+static struct platform_driver __refdata maxim_drivers[] = {
+ {
+ .driver = {
+ .name = "max197",
+ .owner = THIS_MODULE,
+ },
+ .probe = max197_probe,
+ .remove = __devexit_p(max197_remove),
+ }, {
+ .driver = {
+ .name = "max199",
+ .owner = THIS_MODULE,
+ },
+ .probe = max197_probe,
+ .remove = __devexit_p(max197_remove),
+ }
+};
+
+static int __init max197_init(void)
+{
+ int ret;
+ int i;
+
+ for (i = 0; i < ARRAY_SIZE(maxim_drivers); i++) {
+ ret = platform_driver_register(&maxim_drivers[i]);
+ if (ret)
+ goto error_unregister;
+ }
+
+ return 0;
+
+error_unregister:
+ while (--i >= 0)
+ platform_driver_unregister(&maxim_drivers[i]);
+
+ return ret;
+}
+module_init(max197_init);
+
+static void __exit max197_exit(void)
+{
+ int i;
+ for (i = ARRAY_SIZE(maxim_drivers) - 1; i >= 0; i--)
+ platform_driver_unregister(&maxim_drivers[i]);
+}
+module_exit(max197_exit);
+
+MODULE_LICENSE("GPL");
+MODULE_ALIAS("platform:max197");
+MODULE_ALIAS("platform:max199");
+MODULE_AUTHOR("Savoir-faire Linux Inc. <kernel@xxxxxxxxxxxxxxxxxxxx>");
+MODULE_DESCRIPTION("Maxim MAX197 A/D Converter driver");
diff --git a/include/linux/platform_data/max197.h b/include/linux/platform_data/max197.h
new file mode 100644
index 0000000..e2a41dd
--- /dev/null
+++ b/include/linux/platform_data/max197.h
@@ -0,0 +1,21 @@
+/*
+ * Maxim MAX197 A/D Converter Driver
+ *
+ * Copyright (c) 2012 Savoir-faire Linux Inc.
+ * Vivien Didelot <vivien.didelot@xxxxxxxxxxxxxxxxxxxx>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ * For further information, see the Documentation/hwmon/max197 file.
+ */
+
+/**
+ * struct max197_platform_data - MAX197 connectivity info
+ * @convert: Function used to start a conversion with control byte ctrl.
+ * It must return the raw data, or a negative error code.
+ */
+struct max197_platform_data {
+ int (*convert)(u8 ctrl);
+};
--
1.7.11.4
_______________________________________________
lm-sensors mailing list
lm-sensors@xxxxxxxxxxxxxx
http://lists.lm-sensors.org/mailman/listinfo/lm-sensors
