Hello,
Attached, you will find the .conf file I use for my DQ67EP. Here are the
results I get, with i3-2100t.
First raw:
Adapter: ISA adapter
in0: +0.76 V (min = +0.00 V, max = +1.74 V)
in1: +0.77 V (min = +0.00 V, max = +0.00 V) ALARM
in2: +3.41 V (min = +2.98 V, max = +3.63 V)
in3: +3.41 V (min = +2.98 V, max = +3.63 V)
in4: +1.28 V (min = +0.00 V, max = +0.00 V) ALARM
in5: +1.47 V (min = +0.00 V, max = +0.00 V) ALARM
in6: +1.04 V (min = +0.00 V, max = +0.00 V) ALARM
in7: +3.30 V (min = +2.98 V, max = +3.63 V)
in8: +3.20 V (min = +2.70 V, max = +3.30 V)
fan1: 0 RPM (min = 0 RPM, div = 128)
fan2: 937 RPM (min = 0 RPM, div = 32) ALARM
fan3: 0 RPM (min = 0 RPM, div = 128)
fan4: 0 RPM (div = 128)
SYSTIN: +35.0°C (high = +0.0°C, hyst = +0.0°C) ALARM sensor
= diode
CPUTIN: +38.0°C (high = +80.0°C, hyst = +75.0°C) sensor = diode
PECI Agent 0: +36.5°C (high = +80.0°C, hyst = +75.0°C) sensor =
Intel PECI
PCH_CHIP_TEMP: +51.0°C (high = +80.0°C, hyst = +75.0°C)
PECI Agent 1: +0.0°C (high = +80.0°C, hyst = +75.0°C)
cpu0_vid: +0.000 V
intrusion0: OK
and now, with the attached file:
Adapter: ISA adapter
Vcore: +0.77 V (min = +0.60 V, max = +1.60 V)
+12V: +12.29 V (min = +11.14 V, max = +12.93 V)
AVCC: +3.41 V (min = +2.98 V, max = +3.63 V)
+3.3V: +3.41 V (min = +2.98 V, max = +3.63 V)
+5V: +5.12 V (min = +4.70 V, max = +5.31 V)
+1.5V: +1.47 V (min = +1.40 V, max = +1.60 V)
PCH: +1.04 V (min = +0.60 V, max = +1.60 V)
3VSB: +3.30 V (min = +2.98 V, max = +3.63 V)
Vbat: +3.20 V (min = +2.70 V, max = +3.30 V)
Rear fan: 0 RPM (min = 251 RPM, div = 128)
CPU fan: 958 RPM (min = 251 RPM, div = 32)
DIMM temp: +36.0°C (high = +80.0°C, hyst = +75.0°C) sensor = diode
VR temp: +38.5°C (high = +80.0°C, hyst = +75.0°C) sensor = diode
CPU temp: +36.5°C (high = +80.0°C, hyst = +75.0°C) sensor = Intel PECI
PCH temp: +52.0°C (high = +80.0°C, hyst = +75.0°C)
intrusion0: OK
Please see the file.
If you have any questions, just reply. :)
HTH,
[d]
# Created for board DQ67EP using information from Intel Desktop Utilities and BIOS
# "FRONT" and "REAR" fan labels correspond to the motherboard
# headers, but not necessarily the actual fan locations.
chip "nct6775-isa-0290"
# Fans
label fan1 "Rear fan"
set fan1_min 250 # From IDU
label fan2 "CPU fan"
set fan2_min 250 # From IDU
# There is no fan3 on the board
ignore fan3
# There is no fan4 on the board
ignore fan4
# Voltages
# Processor Vcc
label in0 "Vcore"
set in0_min 0.6 # From IDU
set in0_max 1.6 # From IDU
# This should be "12 Volts", but computations are strange
label in1 "+12V"
compute in1 16*@, @/16
set in1_min 11.1 # From IDU
set in1_max 12.9 # From IDU
# AVCC(?) - Not shown in BIOS or IDU
label in2 "AVCC"
set in2_min 3.1 # same as +3.3V
set in2_max 3.5 # same as +3.3V
# +3.3 Volts
label in3 "+3.3V"
set in3_min 3.1 # from IDU
set in3_max 3.5 # from IDU
# +5 Volts
label in4 "+5V"
compute in4 4*@, @/4
set in4_min 4.7 # from IDU
set in4_max 5.3 # from IDU
# Memory Vcc ("SDRAM Vcc" in IDU)
label in5 "+1.5V"
set in5_min 1.4 # from IDU
set in5_max 1.6 # from IDU
# PCH Vcc
label in6 "PCH"
set in6_min 0.6 # from IDU
set in6_max 1.6 # from IDU
# +3.3 Volt Standby
label in7 "3VSB"
set in7_min 3.1 # from IDU
set in7_max 3.5 # from IDU
# VBAT(?) - Not shown in BIOS or IDU
label in8 "Vbat"
# It shows +2.050 V, seems to be not used
ignore cpu0_vid
# Temperatures
# Labeled as "SYSTIN"
# Guess!
label temp1 "DIMM temp"
set temp1_max 80 # From IDU
set temp1_max_hyst 75 # From IDU
# Labeled as "CPUTIN"
label temp2 "VR temp"
set temp2_max 80 # From IDU
set temp2_max_hyst 75 # From IDU
# Labeled as "PECI Agent 0"
# Guess!
label temp3 "CPU temp"
set temp3_max 80 # From IDU
set temp3_max_hyst 75 # From IDU
# Labeled as "PCH_CHIP_TEMP"
label temp7 "PCH temp"
# Labeled as "PECI Agent 1"
# Not used
ignore temp8
_______________________________________________
lm-sensors mailing list
lm-sensors@xxxxxxxxxxxxxx
http://lists.lm-sensors.org/mailman/listinfo/lm-sensors
