On 05/13/12 19:18, James wrote: > On 05/12/12 23:40, Guenter Roeck wrote: >> On Sat, May 12, 2012 at 10:55:13PM -0400, James wrote: >> [ ... ] >>>> >>> Can I assume it is using the module I compiled because it has some data? >>> Still no fan data >>> nct6776-isa-0290 >>> Adapter: ISA adapter >>> Vcore: +0.97 V (min = +0.00 V, max = +1.74 V) >>> in1: +1.85 V (min = +0.00 V, max = +0.00 V) ALARM >>> AVCC: +3.33 V (min = +0.00 V, max = +0.00 V) ALARM >>> +3.3V: +3.31 V (min = +0.00 V, max = +0.00 V) ALARM >>> in4: +1.58 V (min = +0.00 V, max = +0.00 V) ALARM >>> in5: +1.70 V (min = +0.00 V, max = +0.00 V) ALARM >>> 3VSB: +3.44 V (min = +0.00 V, max = +0.00 V) ALARM >>> Vbat: +3.36 V (min = +0.00 V, max = +0.00 V) ALARM >>> fan1: 0 RPM (min = 0 RPM) ALARM >>> fan2: 0 RPM (min = 0 RPM) ALARM >>> fan3: 0 RPM (min = 0 RPM) ALARM >>> fan4: 0 RPM (min = 0 RPM) ALARM >>> fan5: 0 RPM (min = 0 RPM) ALARM >>> SYSTIN: +37.0 C (high = +0.0 C, hyst = +0.0 C) ALARM sensor = thermistor >>> CPUTIN: +37.0 C (high = +80.0 C, hyst = +75.0 C) sensor = thermistor >>> AUXTIN: -1.5 C (high = +80.0 C, hyst = +75.0 C) sensor = thermistor >>> PCH_CHIP_TEMP: +0.0 C >>> PCH_CPU_TEMP: +0.0 C >>> PCH_MCH_TEMP: +0.0 C >> >> Yes, because the above are only seen with the new driver. >> >> Still, see my other e-mail - looks like AsRock is using a gpio pin based multiplexer >> to connect fans to the chip. I looks like specific gpio pins must be enabled to let >> you see fan speeds. >> >> Guenter >> >> > > I bought another case fan and it sees it. > > $ sudo sensors > nouveau-pci-0100 > Adapter: PCI adapter > temp1: +0.0 C (high = +100.0 C, crit = +110.0 C) > > fam15h_power-pci-00c4 > Adapter: PCI adapter > power1: 74.54 W (crit = 95.01 W) > > k10temp-pci-00c3 > Adapter: PCI adapter > temp1: +14.4 C (high = +70.0 C) > (crit = +70.0 C, hyst = +67.0 C) > > nct6776-isa-0290 > Adapter: ISA adapter > Vcore: +0.86 V (min = +0.00 V, max = +1.74 V) > in1: +1.85 V (min = +0.00 V, max = +0.00 V) ALARM > AVCC: +3.33 V (min = +0.00 V, max = +0.00 V) ALARM > +3.3V: +3.33 V (min = +0.00 V, max = +0.00 V) ALARM > in4: +1.58 V (min = +0.00 V, max = +0.00 V) ALARM > in5: +1.70 V (min = +0.00 V, max = +0.00 V) ALARM > 3VSB: +3.46 V (min = +0.00 V, max = +0.00 V) ALARM > Vbat: +3.36 V (min = +0.00 V, max = +0.00 V) ALARM > fan1: 1369 RPM (min = 0 RPM) ALARM > fan2: 0 RPM (min = 0 RPM) ALARM > fan3: 0 RPM (min = 0 RPM) ALARM > fan4: 0 RPM (min = 0 RPM) ALARM > fan5: 0 RPM (min = 0 RPM) ALARM > SYSTIN: +36.0 C (high = +0.0 C, hyst = +0.0 C) ALARM sensor = thermistor > CPUTIN: +35.0 C (high = +80.0 C, hyst = +75.0 C) sensor = thermistor > AUXTIN: -2.0 C (high = +80.0 C, hyst = +75.0 C) sensor = thermistor > PCH_CHIP_TEMP: +0.0 C > PCH_CPU_TEMP: +0.0 C > PCH_MCH_TEMP: +0.0 C > cpu0_vid: +0.000 V > intrusion0: ALARM > intrusion1: ALARM > > It is labelled 'Chassis fan connector 1" by the motherboard manual. > The other is 'Chassis fan 3' > > The difference is fan1 is 3 pin and fan3 is 4 pin. > I will try moving the 4 pin over so it is only using 3 pins. > > _______________________________________________ > lm-sensors mailing list > lm-sensors@xxxxxxxxxxxxxx > http://lists.lm-sensors.org/mailman/listinfo/lm-sensors > :-( Both fans connected but only one shows up. # sensors nouveau-pci-0100 Adapter: PCI adapter temp1: +0.0 C (high = +100.0 C, crit = +110.0 C) fam15h_power-pci-00c4 Adapter: PCI adapter power1: 101.17 W (crit = 95.01 W) k10temp-pci-00c3 Adapter: PCI adapter temp1: +15.2 C (high = +70.0 C) (crit = +70.0 C, hyst = +67.0 C) nct6776-isa-0290 Adapter: ISA adapter Vcore: +0.86 V (min = +0.00 V, max = +1.74 V) in1: +1.85 V (min = +0.00 V, max = +0.00 V) ALARM AVCC: +3.33 V (min = +0.00 V, max = +0.00 V) ALARM +3.3V: +3.33 V (min = +0.00 V, max = +0.00 V) ALARM in4: +1.58 V (min = +0.00 V, max = +0.00 V) ALARM in5: +1.70 V (min = +0.00 V, max = +0.00 V) ALARM 3VSB: +3.46 V (min = +0.00 V, max = +0.00 V) ALARM Vbat: +3.36 V (min = +0.00 V, max = +0.00 V) ALARM fan1: 1374 RPM (min = 0 RPM) ALARM fan2: 0 RPM (min = 0 RPM) ALARM fan3: 0 RPM (min = 0 RPM) ALARM fan4: 0 RPM (min = 0 RPM) ALARM fan5: 0 RPM (min = 0 RPM) ALARM SYSTIN: +36.0 C (high = +0.0 C, hyst = +0.0 C) ALARM sensor = thermistor CPUTIN: +35.5 C (high = +80.0 C, hyst = +75.0 C) sensor = thermistor AUXTIN: -1.5 C (high = +80.0 C, hyst = +75.0 C) sensor = thermistor PCH_CHIP_TEMP: +0.0 C PCH_CPU_TEMP: +0.0 C PCH_MCH_TEMP: +0.0 C cpu0_vid: +0.000 V intrusion0: ALARM intrusion1: ALARM _______________________________________________ lm-sensors mailing list lm-sensors@xxxxxxxxxxxxxx http://lists.lm-sensors.org/mailman/listinfo/lm-sensors
