On IT8782F and IT8783F, some voltage input pins may be disabled. Don't create
sysfs attribute files if that is the case.
Signed-off-by: Guenter Roeck <linux@xxxxxxxxxxxx>
---
drivers/hwmon/it87.c | 146 ++++++++++++++++++++++++++++++++++++++-----------
1 files changed, 113 insertions(+), 33 deletions(-)
diff --git a/drivers/hwmon/it87.c b/drivers/hwmon/it87.c
index aebac13..baf4173 100644
--- a/drivers/hwmon/it87.c
+++ b/drivers/hwmon/it87.c
@@ -234,6 +234,7 @@ struct it87_sio_data {
u8 beep_pin;
u8 internal; /* Internal sensors can be labeled */
/* Features skipped based on config or DMI */
+ u16 skip_in;
u8 skip_vid;
u8 skip_fan;
u8 skip_pwm;
@@ -1371,41 +1372,73 @@ static ssize_t show_name(struct device *dev, struct device_attribute
}
static DEVICE_ATTR(name, S_IRUGO, show_name, NULL);
-static struct attribute *it87_attributes[] = {
+static struct attribute *it87_attributes_in[9][5] = {
+{
&sensor_dev_attr_in0_input.dev_attr.attr,
- &sensor_dev_attr_in1_input.dev_attr.attr,
- &sensor_dev_attr_in2_input.dev_attr.attr,
- &sensor_dev_attr_in3_input.dev_attr.attr,
- &sensor_dev_attr_in4_input.dev_attr.attr,
- &sensor_dev_attr_in5_input.dev_attr.attr,
- &sensor_dev_attr_in6_input.dev_attr.attr,
- &sensor_dev_attr_in7_input.dev_attr.attr,
- &sensor_dev_attr_in8_input.dev_attr.attr,
&sensor_dev_attr_in0_min.dev_attr.attr,
- &sensor_dev_attr_in1_min.dev_attr.attr,
- &sensor_dev_attr_in2_min.dev_attr.attr,
- &sensor_dev_attr_in3_min.dev_attr.attr,
- &sensor_dev_attr_in4_min.dev_attr.attr,
- &sensor_dev_attr_in5_min.dev_attr.attr,
- &sensor_dev_attr_in6_min.dev_attr.attr,
- &sensor_dev_attr_in7_min.dev_attr.attr,
&sensor_dev_attr_in0_max.dev_attr.attr,
- &sensor_dev_attr_in1_max.dev_attr.attr,
- &sensor_dev_attr_in2_max.dev_attr.attr,
- &sensor_dev_attr_in3_max.dev_attr.attr,
- &sensor_dev_attr_in4_max.dev_attr.attr,
- &sensor_dev_attr_in5_max.dev_attr.attr,
- &sensor_dev_attr_in6_max.dev_attr.attr,
- &sensor_dev_attr_in7_max.dev_attr.attr,
&sensor_dev_attr_in0_alarm.dev_attr.attr,
+ NULL
+}, {
+ &sensor_dev_attr_in1_input.dev_attr.attr,
+ &sensor_dev_attr_in1_min.dev_attr.attr,
+ &sensor_dev_attr_in1_max.dev_attr.attr,
&sensor_dev_attr_in1_alarm.dev_attr.attr,
+ NULL
+}, {
+ &sensor_dev_attr_in2_input.dev_attr.attr,
+ &sensor_dev_attr_in2_min.dev_attr.attr,
+ &sensor_dev_attr_in2_max.dev_attr.attr,
&sensor_dev_attr_in2_alarm.dev_attr.attr,
+ NULL
+}, {
+ &sensor_dev_attr_in3_input.dev_attr.attr,
+ &sensor_dev_attr_in3_min.dev_attr.attr,
+ &sensor_dev_attr_in3_max.dev_attr.attr,
&sensor_dev_attr_in3_alarm.dev_attr.attr,
+ NULL
+}, {
+ &sensor_dev_attr_in4_input.dev_attr.attr,
+ &sensor_dev_attr_in4_min.dev_attr.attr,
+ &sensor_dev_attr_in4_max.dev_attr.attr,
&sensor_dev_attr_in4_alarm.dev_attr.attr,
+ NULL
+}, {
+ &sensor_dev_attr_in5_input.dev_attr.attr,
+ &sensor_dev_attr_in5_min.dev_attr.attr,
+ &sensor_dev_attr_in5_max.dev_attr.attr,
&sensor_dev_attr_in5_alarm.dev_attr.attr,
+ NULL
+}, {
+ &sensor_dev_attr_in6_input.dev_attr.attr,
+ &sensor_dev_attr_in6_min.dev_attr.attr,
+ &sensor_dev_attr_in6_max.dev_attr.attr,
&sensor_dev_attr_in6_alarm.dev_attr.attr,
+ NULL
+}, {
+ &sensor_dev_attr_in7_input.dev_attr.attr,
+ &sensor_dev_attr_in7_min.dev_attr.attr,
+ &sensor_dev_attr_in7_max.dev_attr.attr,
&sensor_dev_attr_in7_alarm.dev_attr.attr,
+ NULL
+}, {
+ &sensor_dev_attr_in8_input.dev_attr.attr,
+ NULL
+} };
+static const struct attribute_group it87_group_in[9] = {
+ { .attrs = it87_attributes_in[0] },
+ { .attrs = it87_attributes_in[1] },
+ { .attrs = it87_attributes_in[2] },
+ { .attrs = it87_attributes_in[3] },
+ { .attrs = it87_attributes_in[4] },
+ { .attrs = it87_attributes_in[5] },
+ { .attrs = it87_attributes_in[6] },
+ { .attrs = it87_attributes_in[7] },
+ { .attrs = it87_attributes_in[8] },
+};
+
+static struct attribute *it87_attributes[] = {
&sensor_dev_attr_temp1_input.dev_attr.attr,
&sensor_dev_attr_temp2_input.dev_attr.attr,
&sensor_dev_attr_temp3_input.dev_attr.attr,
@@ -1432,7 +1465,7 @@ static const struct attribute_group it87_group = {
.attrs = it87_attributes,
};
-static struct attribute *it87_attributes_beep[] = {
+static struct attribute *it87_attributes_in_beep[] = {
&sensor_dev_attr_in0_beep.dev_attr.attr,
&sensor_dev_attr_in1_beep.dev_attr.attr,
&sensor_dev_attr_in2_beep.dev_attr.attr,
@@ -1441,7 +1474,10 @@ static struct attribute *it87_attributes_beep[] = {
&sensor_dev_attr_in5_beep.dev_attr.attr,
&sensor_dev_attr_in6_beep.dev_attr.attr,
&sensor_dev_attr_in7_beep.dev_attr.attr,
+ NULL
+};
+static struct attribute *it87_attributes_beep[] = {
&sensor_dev_attr_temp1_beep.dev_attr.attr,
&sensor_dev_attr_temp2_beep.dev_attr.attr,
&sensor_dev_attr_temp3_beep.dev_attr.attr,
@@ -1725,18 +1761,31 @@ static int __init it87_find(unsigned short *address,
/* VIN5 */
if ((reg27 & (1 << 0)) || uart6)
- ; /* No VIN5 */
+ sio_data->skip_in |= (1 << 5); /* No VIN5 */
/* VIN6 */
if ((reg27 & (1 << 1)) || uart6)
- ; /* No VIN6 */
+ sio_data->skip_in |= (1 << 6); /* No VIN6 */
/*
* VIN7
* Does not depend on bit 2 of Reg2C, contrary to datasheet.
*/
- if (reg27 & (1 << 2))
- ; /* No VIN7 (unless internal) */
+ if (reg27 & (1 << 2)) {
+ /*
+ * The data sheet is a bit uncear regarding the internal
+ * voltage divider for VCCH5V. It says
+ * "This bit enables and switches VIN7 (pin91) to the
+ * internal voltage divider for VCCH5V".
+ * This is different to other chips, where the internal
+ * voltage divider would connect VIN7 to an internal
+ * voltage source. Maybe that is the case here as well,
+ * but at least for now follow the data sheet and assume
+ * that there is no VIN7 if pin 91 is not configured as
+ * VIN7 input.
+ */
+ sio_data->skip_in |= (1 << 7);
+ }
if (reg2C & (1 << 0))
sio_data->internal |= (1 << 0);
@@ -1747,6 +1796,7 @@ static int __init it87_find(unsigned short *address,
} else {
int reg;
+ bool uart6;
superio_select(GPIO);
@@ -1784,6 +1834,9 @@ static int __init it87_find(unsigned short *address,
sio_data->vid_value = superio_inb(IT87_SIO_VID_REG);
reg = superio_inb(IT87_SIO_PINX2_REG);
+
+ uart6 = sio_data->type == it8782 && (reg & (1 << 2));
+
/*
* The IT8720F has no VIN7 pin, so VCCH should always be
* routed internally to VIN7 with an internal divider.
@@ -1795,11 +1848,10 @@ static int __init it87_find(unsigned short *address,
* setting. So we force the internal routing in this case.
*
* On IT8782F, VIN7 is multiplexed with one of the UART6 pins.
- * If UART6 is enabled, re-route VIN7 to the internal divider.
+ * If UART6 is enabled, re-route VIN7 to the internal divider
+ * if that is not already the case.
*/
- if ((sio_data->type == it8720 ||
- (sio_data->type == it8782 && (reg & (1 << 2))))
- && !(reg & (1 << 1))) {
+ if ((sio_data->type == it8720 || uart6) && !(reg & (1 << 1))) {
reg |= (1 << 1);
superio_outb(IT87_SIO_PINX2_REG, reg);
pr_notice("Routing internal VCCH to in7\n");
@@ -1810,6 +1862,14 @@ static int __init it87_find(unsigned short *address,
sio_data->type == it8728)
sio_data->internal |= (1 << 1);
+ /*
+ * On IT8782F, UART6 pins overlap with VIN5, VIN6, and VIN7.
+ * While VIN7 can be routed to the internal voltage divider,
+ * VIN5 and VIN6 are not available if UART6 is enabled.
+ */
+ if (uart6)
+ sio_data->skip_in |= (1 << 5) | (1 << 6);
+
sio_data->beep_pin = superio_inb(IT87_SIO_BEEP_PIN_REG) & 0x3f;
}
if (sio_data->beep_pin)
@@ -1847,6 +1907,12 @@ static void it87_remove_files(struct device *dev)
int i;
sysfs_remove_group(&dev->kobj, &it87_group);
+ for (i = 0; i < 9; i++) {
+ sysfs_remove_group(&dev->kobj, &it87_group_in[i]);
+ if (it87_attributes_in_beep[i])
+ sysfs_remove_file(&dev->kobj,
+ it87_attributes_in_beep[i]);
+ }
if (sio_data->beep_pin)
sysfs_remove_group(&dev->kobj, &it87_group_beep);
for (i = 0; i < 5; i++) {
@@ -1945,9 +2011,23 @@ static int __devinit it87_probe(struct platform_device *pdev)
it87_init_device(pdev);
/* Register sysfs hooks */
+ for (i = 0; i < 9; i++) {
+ if (sio_data->skip_in & (1 << i))
+ continue;
+ err = sysfs_create_group(&dev->kobj, &it87_group_in[i]);
+ if (err)
+ goto ERROR4;
+ if (sio_data->beep_pin && it87_attributes_in_beep[i]) {
+ err = sysfs_create_file(&dev->kobj,
+ it87_attributes_in_beep[i]);
+ if (err)
+ goto ERROR4;
+ }
+ }
+
err = sysfs_create_group(&dev->kobj, &it87_group);
if (err)
- goto ERROR2;
+ goto ERROR4;
if (sio_data->beep_pin) {
err = sysfs_create_group(&dev->kobj, &it87_group_beep);
--
1.7.5.4
_______________________________________________
lm-sensors mailing list
lm-sensors@xxxxxxxxxxxxxx
http://lists.lm-sensors.org/mailman/listinfo/lm-sensors
