On Fri, Jan 27, 2012 at 5:54 PM, CC <ccomren@xxxxxxxxx> wrote: > On Fri, Jan 27, 2012 at 3:54 PM, Guenter Roeck > <guenter.roeck@xxxxxxxxxxxx> wrote: >> Forwarding to lm-sensors to keep the group in the loop. >> >> ----- Forwarded message from ccom <reply+i-2970830-11e203ec4162e4680a3e2c999f2bba9b513a1927-1030448@xxxxxxxxxxxxxxxx> ----- >> >> Date: Fri, 27 Jan 2012 09:29:45 -0500 >> From: ccom <reply+i-2970830-11e203ec4162e4680a3e2c999f2bba9b513a1927-1030448@xxxxxxxxxxxxxxxx> >> To: Guenter Roeck <guenter.roeck@xxxxxxxxxxxx> >> Subject: Re: [w83627ehf] Not all fans are shown (#3) >> >> Note that I adapted /etc/sensors3.conf. The output is: >> >> nct6776-isa-0290 >> Adapter: ISA adapter >> VCore: +0.76 V (min = +0.00 V, max = +1.74 V) >> +12V: +12.36 V (min = +0.00 V, max = +0.00 V) ALARM >> AVCC: +3.38 V (min = +0.00 V, max = +0.00 V) ALARM >> +3.3V: +3.36 V (min = +0.00 V, max = +0.00 V) ALARM >> in4: +0.02 V (min = +0.00 V, max = +0.00 V) ALARM >> +5V: +5.04 V (min = +0.00 V, max = +0.00 V) ALARM >> 3VSB: +3.46 V (min = +0.00 V, max = +0.00 V) ALARM >> VBat: +3.30 V (min = +0.00 V, max = +0.00 V) ALARM >> fan1: 0 RPM (min = 0 RPM) ALARM >> fan2: 570 RPM (min = 0 RPM) ALARM >> fan3: 0 RPM (min = 0 RPM) ALARM >> fan4: 1867 RPM (min = 0 RPM) ALARM >> fan5: 0 RPM (min = 0 RPM) ALARM >> SYSTIN: +35.0°C (high = +0.0°C, hyst = +0.0°C) ALARM sensor = thermistor >> CPUTIN: +33.0°C (high = +80.0°C, hyst = +75.0°C) sensor = thermistor >> AUXTIN: +35.5°C (high = +80.0°C, hyst = +75.0°C) sensor = thermistor >> PECI Agent 0: +36.0°C >> cpu0_vid: +2.050 V >> intrusion0: ALARM >> intrusion1: ALARM >> >> There's one more thing missing, though. I cannot find a way to set the fan speed in the sys-dir. >> >> --- >> >> You might also want to set min-max values to get rid of the warnings. Fan speeds are set through pwm[1-3]. >> Did you try to set those ? Chances are that one controls fan2 and another fan4; there does not >> have to be a direct mapping. >> >> Thanks, >> Guenter > > Oh, I forgot to start the daemon since trying out the patch. I did set > the min and max values. > > The correct mapping (triple-checked with the BIOS) for the AsRock Z68 > Pro3-M mainboard, and quite possibly for others -- the +12V > calculation is done as an example in the manual of the chip -- is > given by > > label in1 "+12V" > compute in1 @*6.6,@/6.6 > > label in5 "+5V" > compute in5 @*3,@/3 > > Best, CC I tested all three fan outputs. Another thing is weird: pwm1_mode has its meaning reversed (it's a 3-pin connector and the value 1 is DC mode, in contrast to pwm2 and the documentation). fan1 is controlled by pwm1, which is labelled as CHA_FAN (3-pin connector) fan2 is controlled by pwm2, which is labelled as CPU_FAN (4-pin connector) fan3 does not exist fan4 is not yet controlled, but is labelled PWR_FAN (3-pin connector) fan5 does not exist Best, CC _______________________________________________ lm-sensors mailing list lm-sensors@xxxxxxxxxxxxxx http://lists.lm-sensors.org/mailman/listinfo/lm-sensors
