The probe function has grown pretty large, I think it's time for some
cleanups, starting with these two simple ones:
* Move temp3/in6 check for the W83667HG later in the function, where
it is done for all other chip types.
* Move temperature register setting to a separate function, to avoid
code duplication.
Signed-off-by: Jean Delvare <khali@xxxxxxxxxxxx>
---
Guenter, had you considered adding support for the NCT6775 and NCT6776
to a separate driver? The code starts being seriously bloated :(
drivers/hwmon/w83627ehf.c | 53 +++++++++++++++++++++++++++------------------
1 file changed, 32 insertions(+), 21 deletions(-)
--- linux-3.2-rc0.orig/drivers/hwmon/w83627ehf.c 2011-10-31 14:24:39.000000000 +0100
+++ linux-3.2-rc0/drivers/hwmon/w83627ehf.c 2011-10-31 14:31:50.000000000 +0100
@@ -1853,6 +1853,19 @@ static void w82627ehf_swap_tempreg(struc
}
static void __devinit
+w83627ehf_set_temp_reg_ehf(struct w83627ehf_data *data, int n_temp)
+{
+ int i;
+
+ for (i = 0; i < n_temp; i++) {
+ data->reg_temp[i] = W83627EHF_REG_TEMP[i];
+ data->reg_temp_over[i] = W83627EHF_REG_TEMP_OVER[i];
+ data->reg_temp_hyst[i] = W83627EHF_REG_TEMP_HYST[i];
+ data->reg_temp_config[i] = W83627EHF_REG_TEMP_CONFIG[i];
+ }
+}
+
+static void __devinit
w83627ehf_check_fan_inputs(const struct w83627ehf_sio_data *sio_data,
struct w83627ehf_data *data)
{
@@ -1955,17 +1968,8 @@ static int __devinit w83627ehf_probe(str
|| sio_data->kind == nct6775
|| sio_data->kind == nct6776) ? 3 : 4;
+ /* Default to 3 temperature inputs, code below will adjust as needed */
data->have_temp = 0x07;
- /* Check temp3 configuration bit for 667HG */
- if (sio_data->kind == w83667hg) {
- u8 reg;
-
- reg = w83627ehf_read_value(data, W83627EHF_REG_TEMP_CONFIG[2]);
- if (reg & 0x01)
- data->have_temp &= ~(1 << 2);
- else
- data->in6_skip = 1; /* either temp3 or in6 */
- }
/* Deal with temperature register setup first. */
if (sio_data->kind == nct6775 || sio_data->kind == nct6776) {
@@ -2042,16 +2046,12 @@ static int __devinit w83627ehf_probe(str
} else if (sio_data->kind == w83667hg_b) {
u8 reg;
+ w83627ehf_set_temp_reg_ehf(data, 4);
+
/*
* Temperature sources are selected with bank 0, registers 0x49
* and 0x4a.
*/
- for (i = 0; i < ARRAY_SIZE(W83627EHF_REG_TEMP); i++) {
- data->reg_temp[i] = W83627EHF_REG_TEMP[i];
- data->reg_temp_over[i] = W83627EHF_REG_TEMP_OVER[i];
- data->reg_temp_hyst[i] = W83627EHF_REG_TEMP_HYST[i];
- data->reg_temp_config[i] = W83627EHF_REG_TEMP_CONFIG[i];
- }
reg = w83627ehf_read_value(data, 0x4a);
data->temp_src[0] = reg >> 5;
reg = w83627ehf_read_value(data, 0x49);
@@ -2086,12 +2086,23 @@ static int __devinit w83627ehf_probe(str
data->temp_label = w83667hg_b_temp_label;
} else {
+ w83627ehf_set_temp_reg_ehf(data, 3);
+
/* Temperature sources are fixed */
- for (i = 0; i < 3; i++) {
- data->reg_temp[i] = W83627EHF_REG_TEMP[i];
- data->reg_temp_over[i] = W83627EHF_REG_TEMP_OVER[i];
- data->reg_temp_hyst[i] = W83627EHF_REG_TEMP_HYST[i];
- data->reg_temp_config[i] = W83627EHF_REG_TEMP_CONFIG[i];
+
+ if (sio_data->kind == w83667hg) {
+ u8 reg;
+
+ /*
+ * Chip supports either AUXTIN or VIN3. Try to find
+ * out which one.
+ */
+ reg = w83627ehf_read_value(data,
+ W83627EHF_REG_TEMP_CONFIG[2]);
+ if (reg & 0x01)
+ data->have_temp &= ~(1 << 2);
+ else
+ data->in6_skip = 1;
}
}
--
Jean Delvare
_______________________________________________
lm-sensors mailing list
lm-sensors@xxxxxxxxxxxxxx
http://lists.lm-sensors.org/mailman/listinfo/lm-sensors
