Again, with atk0110 loaded (after I noticed the warning in dmesg about using
acpi_enforce_resources kernel parameter preventing atk module from loading).
All values provided again for comparison.
$ sensors
k10temp-pci-00c3
Adapter: PCI adapter
temp1: +28.5°C (high = +70.0°C)
(crit = +70.0°C, hyst = +65.0°C)
atk0110-acpi-0
Adapter: ACPI interface
Vcore Voltage: +1.27 V (min = +0.85 V, max = +1.60 V)
+3.3 Voltage: +3.28 V (min = +2.97 V, max = +3.63 V)
+5 Voltage: +5.06 V (min = +4.50 V, max = +5.50 V)
+12 Voltage: +12.13 V (min = +10.20 V, max = +13.80 V)
CPU FAN Speed: 2616 RPM (min = 600 RPM)
CHASSIS FAN Speed: 1562 RPM (min = 600 RPM)
POWER FAN Speed: 1683 RPM (min = 600 RPM)
CPU Temperature: +37.0°C (high = +60.0°C, crit = +95.0°C)
MB Temperature: +35.0°C (high = +45.0°C, crit = +75.0°C)
it8721-isa-0290
Adapter: ISA adapter
VCore: +2.92 V (min = +1.82 V, max = +0.17 V) ALARM
VDDR: +2.89 V (min = +2.34 V, max = +2.06 V) ALARM
+3.3V: +1.27 V (min = +2.10 V, max = +2.68 V) ALARM
+5V: +3.29 V (min = +2.38 V, max = +2.90 V) ALARM
+12V: +1.70 V (min = +2.82 V, max = +1.31 V) ALARM
in5: +2.63 V (min = +2.10 V, max = +1.40 V) ALARM
in6: +1.01 V (min = +1.99 V, max = +1.25 V) ALARM
VSB: +4.27 V (min = +1.30 V, max = +2.76 V) ALARM
VBat: +3.34 V
CPU fan: 2606 RPM (min = 14 RPM)
CHA fan: 1566 RPM (min = 24 RPM)
PSU fan: 1683 RPM (min = 21 RPM)
CPU Temp: +37.0°C (low = +0.0°C, high = +70.0°C) sensor = thermistor
MB Temp: +35.0°C (low = +0.0°C, high = +70.0°C) sensor = thermistor
atk driver provides values very close to bios, with following exceptions:
- cpu temp is lower (46° in bios), in my understanding cpu is at full
speed during bios so it can explain
- chassis fan lower (1717 RPM in bios), most probably related to higher cpu
temperature, as its speed under OS follows CPU temperature
- power fan min RPM cannot be set in the bios, others are consistent with my
settings
- MB temperature shutdown level in bios is 95°. Not sure if it contradicts
"crit" level reported above (maybe unrelated).
For some reason, when changing fan settings in bios, linux fails booting after
detecting all hard disks, undoing the config doesn't always cure startup. I
could originally boot in "auto" mode, now I can bot in "manual" mode (bios
controls fans, but I get to set the levels - for no audible difference
anyway). I suspect bios has a good share of bugs (it seems this motherboard is
more recent than I thought... dmidecode says "Release Date: 04/18/2011" in
"BIOS Information" section).
--
Vincent Pelletier
_______________________________________________
lm-sensors mailing list
lm-sensors@xxxxxxxxxxxxxx
http://lists.lm-sensors.org/mailman/listinfo/lm-sensors
