Hi,
On 08/04/2010 05:44 PM, Giel van Schijndel wrote:
On Wed, Aug 04, 2010 at 13:36:22 +0200, Hans de Goede wrote:
On 08/01/2010 03:30, Giel van Schijndel wrote:
Allow device probing to recognise the Fintek F71808E.
Sysfs interface:
* Fan/pwm control is the same as for F71889FG
My datasheet strongly disagrees with this the F71889FG has 5 pwm zones
each with their own speed divided by 4 boundary temps, where as
the F71808E has 3 pwm zones divided by 2 boundary temps. So it is much
more like the F71862FG, which also has 2 boundary temps, and 3 pwm zones,
*but* the F71862FG has one pwm zone hardwired to 100%.
I'm assuming that by "pwm zone" you mean a separate PWM output channel?
I.e. each "pwm zone" controls a single fan?
With pwm zone I mean the number of different speeds which can be programmed
for one output channel, the temps divide the entire temp range into zones
(number of zones == number of temps + 1) and for each zone one can then
tell at what speed / pwm setting the fan should operate when the temperature
is in that zone.
<snip>
Also while making changes, I must say I don't like the splitting
of fxxxx_temp_attr into fxxxx_temp_attr and f71862_temp_attr just because
the number of sensors differs. I think it would be better to instead
make fxxxx_temp_attr a 2 dimensional array like fxxxx_fan_attr and like
with fxxxx_fan_attr register as many sensor attr blocks as the specific
model has.
Right, that's probably a nicer way of going about it, I think that might
be easier done in a separate patch (most likely preceding the addition
of F71808E support), though I'll look at that.
Yes first splitting the attr in a separate patch would be very good.
Signed-off-by: Giel van Schijndel<me@xxxxxxxxx>
---
Documentation/hwmon/f71882fg | 4 ++
drivers/hwmon/Kconfig | 6 ++--
drivers/hwmon/f71882fg.c | 83 ++++++++++++++++++++++++++++++++++++++----
3 files changed, 82 insertions(+), 11 deletions(-)
diff --git a/Documentation/hwmon/f71882fg b/Documentation/hwmon/f71882fg
index a7952c2..1a07fd6 100644
--- a/Documentation/hwmon/f71882fg
+++ b/Documentation/hwmon/f71882fg
@@ -2,6 +2,10 @@ Kernel driver f71882fg
======================
Supported chips:
+ * Fintek F71808E
+ Prefix: 'f71808fg'
This is wrong, as you already indicate and the datasheet as well this
chip in question is an f71808e not an f71808fg, also note that there is
an f71808a model as well which is different (and has a different super io
chip id).
Ah yes, I think I, wrongly, assumed that 'fg' was just some suffix used
in this driver. For example, I cannot find F71889FG in the datasheet I
have, only 'F71889' along with 'F71889F' in the section "Ordering
Information" (for the F71889 I've got datasheet version V0.17P released
December 2008).
I have a V0.27P datasheet for the 71889, but yes the fg suffix does not
seem to be mentioned anywhere in the datasheet not sure where it comes from.
I do know however that there are now new chips coming out with different
a and e suffixes so I suggest that we stay with fg for the old chips and
use a and e to distuingish the new ones.
At the same time the F71808E datasheet I have clearly marks the chip as
F71808E all over the entire datasheet (version V0.17P released October
2009).
Right.
Either way I changed that ^^ portion of documentation while changing the
enumeration value 'f71808fg' -> 'f71808e' in the code itself as well.
Good.
One last request in the second switch case in f71882fg_remove()
there is a default label which contains a comment which models it applies
to, please add the f71808e to that comment.
Wouldn't it be better, to instead replace that 'default' label with a
serie of case labels that code applies to? Along with providing the
same documentation effect (expressed in C instead of English) it would
cause GCC to warn whenever one of the chips was forgotten in a switch
statement.
Ack, if you could do that that would be great! Please do that
in a preparation patch though and not in the main patch.
<snip>
PS For comparison, which datasheet versions do you have?
All Fintek datasheets I have access to:
* F71808E - V0.17P, October 2009
* F71858 - V0.26P, July 2007
* F71862 - V0.28P, July 2008
* F71882 - V0.24P, November 2006
* F71889 - V0.17P, December 2008
Those most interesting are of course the F71808E, F71862 and F71889---as
you refer to those in your text. This because I have already had
experience with a hardware vendor giving me the wrong datasheets and
would like to prevent any such mistakes from causing similar
communication problems here.
Here is my list:
F71612A_V020P.pdf
F71808A_V0.15P.pdf
F71808E_V0.20P.pdf
F71858_V026P.pdf
F71862_V028P.pdf
F71869E_V0.19P.pdf
F71869_V1.1.pdf
F71882_V0.24P.pdf
F71889E_V0.19P.pdf
F71889_V0.27P.pdf
F8000_REG.pdf
Regards,
Hans
_______________________________________________
lm-sensors mailing list
lm-sensors@xxxxxxxxxxxxxx
http://lists.lm-sensors.org/mailman/listinfo/lm-sensors