As kind is now hard-coded to -1, there is room for code clean-ups.
Signed-off-by: Jean Delvare <khali@xxxxxxxxxxxx>
Cc: Marc Hulsman <m.hulsman@xxxxxxxxxx>
---
drivers/hwmon/w83791d.c | 60 ++++++++++++++---------------------------------
1 file changed, 18 insertions(+), 42 deletions(-)
--- linux-2.6.32-rc3.orig/drivers/hwmon/w83791d.c 2009-10-06 10:33:15.000000000 +0200
+++ linux-2.6.32-rc3/drivers/hwmon/w83791d.c 2009-10-06 12:13:28.000000000 +0200
@@ -1270,56 +1270,32 @@ static int w83791d_detect(struct i2c_cli
return -ENODEV;
}
- /* The w83791d may be stuck in some other bank than bank 0. This may
- make reading other information impossible. Specify a force=...
- parameter, and the Winbond will be reset to the right bank. */
- if (kind < 0) {
- if (w83791d_read(client, W83791D_REG_CONFIG) & 0x80) {
- return -ENODEV;
- }
- val1 = w83791d_read(client, W83791D_REG_BANK);
- val2 = w83791d_read(client, W83791D_REG_CHIPMAN);
- /* Check for Winbond ID if in bank 0 */
- if (!(val1 & 0x07)) {
- /* yes it is Bank0 */
- if (((!(val1 & 0x80)) && (val2 != 0xa3)) ||
- ((val1 & 0x80) && (val2 != 0x5c))) {
- return -ENODEV;
- }
- }
- /* If Winbond chip, address of chip and W83791D_REG_I2C_ADDR
- should match */
- if (w83791d_read(client, W83791D_REG_I2C_ADDR) != address) {
+ if (w83791d_read(client, W83791D_REG_CONFIG) & 0x80)
+ return -ENODEV;
+
+ val1 = w83791d_read(client, W83791D_REG_BANK);
+ val2 = w83791d_read(client, W83791D_REG_CHIPMAN);
+ /* Check for Winbond ID if in bank 0 */
+ if (!(val1 & 0x07)) {
+ if ((!(val1 & 0x80) && val2 != 0xa3) ||
+ ( (val1 & 0x80) && val2 != 0x5c)) {
return -ENODEV;
}
}
+ /* If Winbond chip, address of chip and W83791D_REG_I2C_ADDR
+ should match */
+ if (w83791d_read(client, W83791D_REG_I2C_ADDR) != address)
+ return -ENODEV;
- /* We either have a force parameter or we have reason to
- believe it is a Winbond chip. Either way, we want bank 0 and
- Vendor ID high byte */
+ /* We want bank 0 and Vendor ID high byte */
val1 = w83791d_read(client, W83791D_REG_BANK) & 0x78;
w83791d_write(client, W83791D_REG_BANK, val1 | 0x80);
/* Verify it is a Winbond w83791d */
- if (kind <= 0) {
- /* get vendor ID */
- val2 = w83791d_read(client, W83791D_REG_CHIPMAN);
- if (val2 != 0x5c) { /* the vendor is NOT Winbond */
- return -ENODEV;
- }
- val1 = w83791d_read(client, W83791D_REG_WCHIPID);
- if (val1 == 0x71) {
- kind = w83791d;
- } else {
- if (kind == 0)
- dev_warn(&adapter->dev,
- "w83791d: Ignoring 'force' parameter "
- "for unknown chip at adapter %d, "
- "address 0x%02x\n",
- i2c_adapter_id(adapter), address);
- return -ENODEV;
- }
- }
+ val1 = w83791d_read(client, W83791D_REG_WCHIPID);
+ val2 = w83791d_read(client, W83791D_REG_CHIPMAN);
+ if (val1 != 0x71 || val2 != 0x5c)
+ return -ENODEV;
strlcpy(info->type, "w83791d", I2C_NAME_SIZE);
--
Jean Delvare
_______________________________________________
lm-sensors mailing list
lm-sensors@xxxxxxxxxxxxxx
http://lists.lm-sensors.org/mailman/listinfo/lm-sensors
