Hi,
I sent this to you in January, but forgot to tell the MB model, sorry.
It was an EPoX EP-9HEAI. I hope the information is complete and OK now,
as I don't have it anymore. TX
Eric Schumann
acpitz-virtual-0
Adapter: Virtual device
temp1: +33.0°C (crit = +70.0°C)
k8temp-pci-00c3
Adapter: PCI adapter
Core0 Temp: +19.0°C
w83687thf-isa-0290
Adapter: ISA adapter
in0: +1.13 V (min = +0.70 V, max = +1.87 V)
in1: +3.26 V (min = +0.62 V, max = +1.01 V) ALARM
in2: +2.50 V (min = +2.37 V, max = +3.94 V)
in3: +2.98 V (min = +4.06 V, max = +3.30 V) ALARM
in4: +1.49 V (min = +3.97 V, max = +2.42 V) ALARM
in7: +2.98 V (min = +3.06 V, max = +0.29 V) ALARM
in8: +3.33 V (min = +1.97 V, max = +4.03 V)
fan1: 0 RPM (min = 694 RPM, div = 8) ALARM
fan2: 1814 RPM (min = 688 RPM, div = 8)
fan3: 0 RPM (min = 922 RPM, div = 8) ALARM
temp1: +27.0°C (high = -67.0°C, hyst = -105.0°C) ALARM sensor = thermistor
temp2: +33.5°C (high = +72.0°C, hyst = +70.0°C) sensor = thermistor
temp3: +13.0°C (high = +70.0°C, hyst = +65.0°C) sensor = thermistor
beep_enable:enabled
acpitz-virtual-0
Adapter: Virtual device
temp1: +33.0°C (crit = +70.0°C)
k8temp-pci-00c3
Adapter: PCI adapter
temp1: +18.0°C
w83687thf-isa-0290
Adapter: ISA adapter
VCore: +1.14 V (min = +0.70 V, max = +1.87 V)
+3.3V: +3.26 V (min = +3.14 V, max = +3.47 V)
Vdim: +2.50 V (min = +2.48 V, max = +2.93 V)
+5V: +5.03 V (min = +4.76 V, max = +5.24 V)
Chip: +1.49 V (min = +1.49 V, max = +1.76 V)
5VSB: +5.00 V (min = +4.76 V, max = +5.24 V)
VBat: +3.33 V (min = +2.40 V, max = +3.60 V)
Chassis Fan: 620 RPM (min = 399 RPM, div = 16)
CPU Fan: 1757 RPM (min = 688 RPM, div = 8)
Power Fan 2 B bought: 0 RPM (min = 917 RPM, div = 16) ALARM
System Temp: +27.0°C (high = +50.0°C, hyst = +45.0°C) sensor = thermistor
CPU Temp: +33.5°C (high = +72.0°C, hyst = +70.0°C) sensor = thermistor
Strange Temp: +10.0°C (high = +70.0°C, hyst = +65.0°C) sensor = thermistor
beep_enable: enabled
# W83687THF w83627hf 2.10.0 2.6.17 Super I/O, mostly similar to the W83627THF. Support contributed by Jean Delvare.
#found on EPoX EP-9HEAI V3.0 VIA KT890 Socket 939
chip "w83687thf-*"
label in0 "VCore"
label in1 "+3.3V"
label in2 "Vdim"
label in3 "+5V" # "+5V"
label in4 "Chip"
label in5 "not shown by sensors"
label in6 "not shown by sensors"
label in7 "5VSB"
label in8 "VBat"
compute in3 ((6.8/10)+1)*@ , @/((6.8/10)+1)
# compute in4 ((28/10)+1)*@ , @/((28/10)+1)
# compute in5 (5.14 * @) - 14.91 , (@ + 14.91) / 5.14
# compute in6 (3.14 * @) - 7.71 , (@ + 7.71) / 3.14
compute in7 ((6.8/10)+1)*@ , @/((6.8/10)+1)
# adjust this if your vid is wrong; see doc/vid
# set vrm 9.0
# set limits to 5% for the critical voltages
# set limits to 10% for the non-critical voltages
# set limits to 20% for the battery voltage
# set in0_min vid*0.95
# set in0_max vid*1.05
set in1_min 3.3 * 0.95
set in1_max 3.3 * 1.05
set in2_min 2.5 * 0.99
set in2_max 2.5 * 1.17
set in3_min 5.0 * 0.95
set in3_max 5.0 * 1.05
set in4_min 1.5 * 0.99
set in4_max 1.5 * 1.17
# set in5_max -12 * 0.90
# set in5_min -12 * 1.10
# set in6_max -5 * 0.95
# set in6_min -5 * 1.05
set in7_min 5 * 0.95
set in7_max 5 * 1.05
set in8_min 3.0 * 0.80
set in8_max 3.0 * 1.20
# set up sensor types (thermistor is default)
# 1 = PII/Celeron Diode; 2 = 3904 transistor;
# 3435 = thermistor with Beta = 3435
# If temperature changes very little, try 1 or 2.
# set sensor1 1
# set sensor2 2
# set sensor3 3435
# temperature limits
set temp1_max 50
set temp1_max_hyst 45
# temp 3 less than room temp (hopefully current: 8°), perhaps wifi 2 fridge
label temp1 "System Temp"
label temp2 "CPU Temp"
label temp3 "Strange Temp"
# ignore temp3
label fan2 "CPU Fan"
label fan3 "Power Fan 2 B bought"
label fan1 "Chassis Fan"
set fan1_div 16
#set fan2_div 8
set fan3_div 16
set fan1_min 400
_______________________________________________
lm-sensors mailing list
lm-sensors@xxxxxxxxxxxxxx
http://lists.lm-sensors.org/mailman/listinfo/lm-sensors
