I have just setup a EVGA nForce 750i motherboard for Ubuntu (8.10 testing) & have several ALARM sections. Question is how do I just report the voltages/fan speeds without alarms? I am using 3.02 supplied by Ubuntu--listed as sensors are: lm78-i2c-1-2d, w83627dhg-isa-0290, coretemp & acpitz-virtual-0 The coretemp & acpitz-virtual-0 are working in range--most of the readings for the lm78 & w83627dhg are throwing alarms even after I spread the voltage/fanspeed ranges. Output follows: acpitz-virtual-0 Adapter: Virtual device temp1: +40.0?C (crit = +60.0?C) lm78-i2c-1-2d Adapter: SMBus nForce2 adapter at 1c80 VCore 1: +2.53 V (min = +2.18 V, max = +3.25 V) VCore 2: +2.10 V (min = +1.86 V, max = +3.25 V) ALARM +3.3V: +3.31 V (min = +2.30 V, max = +3.47 V) ALARM +5V: +3.31 V (min = +3.50 V, max = +4.08 V) ALARM +12V: +2.56 V (min = +4.08 V, max = +4.08 V) ALARM -12V: +3.10 V (min = +0.00 V, max = +0.00 V) ALARM -5V: +3.66 V (min = +0.00 V, max = +0.00 V) ALARM fan1: 2986 RPM (min = 2657 RPM, div = 2) ALARM fan2: 2556 RPM (min = 998 RPM, div = 8) ALARM fan3: 4963 RPM (min = 10714 RPM, div = 2) ALARM temp1: +98.0?C (high = +100.0?C, hyst = +120.0?C) ALARM cpu0_vid: +3.100 V w83627dhg-isa-0290 Adapter: ISA adapter VCore: +1.26 V (min = +1.09 V, max = +1.62 V) in1: +6.86 V (min = +6.12 V, max = +10.72 V) AVCC: +3.31 V (min = +2.30 V, max = +3.47 V) 3VCC: +3.31 V (min = +3.50 V, max = +4.08 V) ALARM in4: +1.28 V (min = +2.04 V, max = +2.04 V) ALARM in5: +1.55 V (min = +0.00 V, max = +0.00 V) ALARM in6: +5.86 V (min = +0.00 V, max = +0.00 V) ALARM VSB: +3.31 V (min = +1.57 V, max = +0.02 V) ALARM VBAT: +3.02 V (min = +0.10 V, max = +1.54 V) ALARM Case Fan: 3000 RPM (min = 2657 RPM, div = 2) CPU Fan: 2556 RPM (min = 998 RPM, div = 8) Aux Fan: 1240 RPM (min = 2678 RPM, div = 8) ALARM fan4: 1622 RPM (min = 912 RPM, div = 8) fan5: 0 RPM (min = 0 RPM, div = 128) ALARM Sys Temp: +98.0?C (high = +100.0?C, hyst = +120.0?C) sensor = thermistor CPU Temp: +52.5?C (high = +127.0?C, hyst = +0.0?C) sensor = transistor AUX Temp: +37.0?C (high = +127.0?C, hyst = +0.0?C) sensor = thermistor coretemp-isa-0000 Adapter: ISA adapter Core 0: +60.0?C (high = +80.0?C, crit = +100.0?C) coretemp-isa-0001 Adapter: ISA adapter Core 1: +61.0?C (high = +80.0?C, crit = +100.0?C) coretemp-isa-0002 Adapter: ISA adapter Core 2: +64.0?C (high = +80.0?C, crit = +100.0?C) coretemp-isa-0003 Adapter: ISA adapter Core 3: +65.0?C (high = +80.0?C, crit = +100.0?C)
