Hi Dmitry, On 10/2/07, Dmitry <admin at incred.org> wrote: > In letter Mon, 01 Oct 2007 10:06:58 -0700, Juerg Haefliger wrote: > > > > Can you please post the full output of sensors-detect? > > > > ...juerg > > > yes, i can... > > ################################## > $ sudo sensors-detect > Password: > # sensors-detect revision 4171 (2006-09-24 03:37:01 -0700) > > This program will help you determine which kernel modules you need > to load to use lm_sensors most effectively. It is generally safe > and recommended to accept the default answers to all questions, > unless you know what you're doing. > > We can start with probing for (PCI) I2C or SMBus adapters. > Do you want to probe now? (YES/no): yes > Probing for PCI bus adapters... > Use driver `i2c-viapro' for device 0000:00:07.3: VIA Technologies > VT82C596 Apollo ACPI > > We will now try to load each adapter module in turn. > Module `i2c-viapro' already loaded. > If you have undetectable or unsupported adapters, you can have them > scanned by manually loading the modules before running this script. > > To continue, we need module `i2c-dev' to be loaded. > Do you want to load `i2c-dev' now? (YES/no): yes > Module loaded successfully. > > We are now going to do the I2C/SMBus adapter probings. Some chips may > be double detected; we choose the one with the highest confidence > value in that case. > If you found that the adapter hung after probing a certain address, > you can specify that address to remain unprobed. > > Next adapter: SMBus Via Pro adapter at 5000 > Do you want to scan it? (YES/no/selectively): yes > Client found at address 0x51 > Handled by driver `eeprom' (already loaded), chip type `eeprom' > Client found at address 0x69 > > Some chips are also accessible through the ISA I/O ports. We have to > write to arbitrary I/O ports to probe them. This is usually safe though. > Yes, you do have ISA I/O ports even if you do not have any ISA slots! > Do you want to scan the ISA I/O ports? (YES/no): yes > Probing for `National Semiconductor LM78' at 0x290... No > Probing for `National Semiconductor LM78-J' at 0x290... No > Probing for `National Semiconductor LM79' at 0x290... No > Probing for `Winbond W83781D' at 0x290... No > Probing for `Winbond W83782D' at 0x290... No > Probing for `Winbond W83627HF' at 0x290... No > Probing for `Silicon Integrated Systems SIS5595'... No > Probing for `VIA VT82C686 Integrated Sensors'... No > Probing for `VIA VT8231 Integrated Sensors'... No > Probing for `AMD K8 thermal sensors'... No > Probing for `IPMI BMC KCS' at 0xca0... No > Probing for `IPMI BMC SMIC' at 0xca8... No > > Some Super I/O chips may also contain sensors. We have to write to > standard I/O ports to probe them. This is usually safe. > Do you want to scan for Super I/O sensors? (YES/no): yes > Probing for Super-I/O at 0x2e/0x2f > Trying family `ITE'... No > Trying family `National Semiconductor'... No > Trying family `SMSC'... No > Trying family `VIA/Winbond/Fintek'... No > Probing for Super-I/O at 0x4e/0x4f > Trying family `ITE'... No > Trying family `National Semiconductor'... No > Trying family `SMSC'... No > Trying family `VIA/Winbond/Fintek'... No > > Now follows a summary of the probes I have just done. > Just press ENTER to continue: > > Driver `eeprom' (should be inserted): > Detects correctly: > * Bus `SMBus Via Pro adapter at 5000' > Busdriver `i2c-viapro', I2C address 0x51 > Chip `eeprom' (confidence: 6) > > EEPROMs are *NOT* sensors! They are data storage chips commonly > found on memory modules (SPD), in monitors (EDID), or in some > laptops, for example. > > I will now generate the commands needed to load the required modules. > Just press ENTER to continue: > > > If you want to load the modules at startup, generate a config file > below and make sure lm_sensors gets started at boot time; e.g > $ rc-update add lm_sensors default > To make the sensors modules behave correctly, add these lines to > /etc/modules.d/lm_sensors and run modules-update: > > #----cut here---- > # I2C module options > alias char-major-89 i2c-dev > #----cut here---- > > If you have some drivers built into your kernel, the list above will > contain too many modules. Skip the appropriate ones! You really > should try these commands right now to make sure everything is > working properly. Monitoring programs won't work until the needed > modules are loaded. > > To load everything that is needed, execute the commands below... > > #----cut here---- > # I2C adapter drivers > modprobe i2c-viapro > # Chip drivers > modprobe eeprom > # sleep 2 # optional > /usr/bin/sensors -s # recommended > #----end cut here---- > > Do you want to overwrite /etc/conf.d/lm_sensors? Enter s to specify other > file name? > (yes/NO/s): > ########################### > Sensors-detect didn't find anything. What makes you think you have a HW-monitoring chip? Does the BIOS show any voltages/temps? Have you tried the latest version of sensors-detect (2.10.4)? What's your mobo model? ...juerg
