Hi Rick, The 0 RPM fan speeds are probably due to the minimum fan speed limits for triggering the alarms. To be brief, add something like this to your sensors.conf: set fan1_min 0 set fan2_min 0 set fan3_min 0 set fan4_min 0 set fan5_min 0 (Note that after you do this, you have changed what will trigger an alarm. You should check that your system does not overheat.) This should get the driver to look "low enough" to find your fan RPM. You can then modify sensors.conf to have a reasonable minimum for your fans, or possible even ignore alarms generated by your fans. Hope that helps, David On 2/12/07, Rick Wright <riwright at vt.edu> wrote: > Rick Wright wrote: > > >Hello list, > > > >I have the Abit AT8 mobo described in the subject line and I'm trying to > >get lm_sensors working properly for this board. I see there is still > >very recent activity concerning getting this Winbond chip fully > >supported. In the latest 2.10.2 release I see Dave Platt added these > >changes relavent to my board: > > > >Program sensord: > > Add w83627ehf voltage support (Dave Platt) > > Add k8temp support (Dave Platt) > > > >These additions appear to be working properly OOTB as the "sensors" > >command produces the following output: > > > >[riwright at box ~]$ sensors > >k8temp-pci-00c3 > >Adapter: PCI adapter > >Core0 Temp: > > +45 ?C > >Core1 Temp: > > +46 ?C > > > >w83627ehf-isa-0290 > >Adapter: ISA adapter > >VCore: +2.04 V (min = +0.00 V, max = +1.74 V) ALARM > >in1: +13.46 V (min = +13.46 V, max = +12.36 V) ALARM > >AVCC: +3.22 V (min = +3.02 V, max = +4.08 V) > >3VCC: +3.22 V (min = +3.92 V, max = +3.82 V) ALARM > >in4: +1.66 V (min = +2.01 V, max = +1.01 V) ALARM > >in5: +1.66 V (min = +1.16 V, max = +0.95 V) ALARM > >in6: +5.32 V (min = +6.53 V, max = +6.32 V) ALARM > >VSB: +3.07 V (min = +4.08 V, max = +3.06 V) ALARM > >VBAT: +2.16 V (min = +2.02 V, max = +2.38 V) > >in9: +1.56 V (min = +1.98 V, max = +1.75 V) ALARM > >Case Fan: 0 RPM (min = 1318 RPM, div = 128) ALARM > >CPU Fan: 0 RPM (min = 1757 RPM, div = 128) ALARM > >Aux Fan: 0 RPM (min = 10546 RPM, div = 128) ALARM > >fan4: 0 RPM (min = 10546 RPM, div = 128) ALARM > >fan5: 0 RPM (min = 168750 RPM, div = 8) ALARM > >Sys Temp: -48 ?C (high = +45 ?C, hyst = +40 ?C) > >CPU Temp: -48.0 ?C (high = +45.0 ?C, hyst = +40.0 ?C) > >AUX Temp: -48.0 ?C (high = +80.0 ?C, hyst = +75.0 ?C) > > > > > >So, as advertized, the Voltage support seems to be working. However, > >the fan speeds and temperatures do not. Are these items currently > >supported yet? Or do I have a configuration problem? If not yet > >supported, is this planned for the future? > > > >Any input/hints/pointers greatly appreciated. > > > >Thanks, > >Rick > > > >_______________________________________________ > >lm-sensors mailing list > >lm-sensors at lm-sensors.org > >http://lists.lm-sensors.org/mailman/listinfo/lm-sensors > > > > > > > > > _______________________________________________ > lm-sensors mailing list > lm-sensors at lm-sensors.org > http://lists.lm-sensors.org/mailman/listinfo/lm-sensors >
