Rudolf Marek wrote: > >> temp2): Under load, my temp3 *drops* from 119 to 103.5 under load and >> then goes back up afterwards ????? >> > > Hmm my MB has this at 127C which means unconnected. Please can you send a > dsdt.bin file? (cat /proc/acpi/dsdt > /tmp/dsdt.bin) > This machine is powered down right now. I'll send this shortly. > >> fan1: (you state it should be the CPU_FAN) The RPM in the 1100 range >> matches what I'm seeing in the BIOS for CHA_FAN1 and CHA_FAN2 (both are >> documented to run at 1800 RPM) >> > > ok > > >> fan2: (you state it should be CHA_FAN1) The RPM of 2537 is consistent >> with what I'm seeing in the BIOS for CPU_FAN (a Zalman CNPS9500 LED) >> fan3: (you state it should be CHA_FAN2) My fan3 shows 0, but I have >> verified both fans are spinning and connected to CHA_FAN1 and CHA_FAN2 >> fan4: (you state this is PWR_FAN): The P5B manual states that this >> connector is not supported by their QFan2 software monitoring. I doubt >> it would be monitorable. >> > > Hmm how many/what fans can you see in the BIOS? > I'll get that shortly also. Just wanted to let you know that I see some strange behavior of lm_sensors with respect to the fan5. This sensor usually reports zero. But after it has been up for a while it starts reporting something in the 1100 to 1200 range. This is consistent with my case fan speed. So it seems fan5 is either CHA_FAN1 or CHA_FAN2. Actually, I can't confirm it's the fan5 sensor that's doing this. That is what I remember from a couple of days ago. But I updated my sensors.conf file to put a label on the sensor that was doing this, so once I power up my machine again, I'll verify this as well. > here is my: > > axon:~# sensors > w83627dhg-isa-0290 > Adapter: ISA adapter > VCore: +1.14 V (min = +0.00 V, max = +1.74 V) > in1: +12.30 V (min = +0.26 V, max = +10.88 V) ALARM > AVCC: +3.25 V (min = +1.74 V, max = +2.24 V) ALARM > 3VCC: +3.25 V (min = +3.44 V, max = +3.17 V) ALARM > in4: +1.11 V (min = +1.17 V, max = +0.26 V) ALARM > in5: +1.59 V (min = +0.06 V, max = +1.54 V) ALARM > in6: +3.53 V (min = +0.51 V, max = +1.00 V) ALARM > VSB: +3.25 V (min = +1.74 V, max = +3.66 V) > VBAT: +3.25 V (min = +0.05 V, max = +0.64 V) ALARM > Case Fan: 0 RPM (min = 21093 RPM, div = 64) ALARM > CPU Fan: 1687 RPM (min = 1662 RPM, div = 4) > Aux Fan: 0 RPM (min = 10546 RPM, div = 64) ALARM > fan4: 0 RPM (min = 10546 RPM, div = 32) ALARM > fan5: 3835 RPM (min = 7670 RPM, div = 2) ALARM > Sys Temp: +33?C (high = -56?C, hyst = +39?C) > CPU Temp: +39.5?C (high = +80.0?C, hyst = +75.0?C) > AUX Temp: +127.0?C (high = +80.0?C, hyst = +75.0?C) ALARM > > coretemp-isa-0000 > Adapter: ISA adapter > temp1: +30?C (high = +85?C) > > coretemp-isa-0001 > Adapter: ISA adapter > temp1: +32?C (high = +85?C) > > Rudolf > I forget, is your board a P5B Deluxe WiFi?
