Hi, a bunch of explanations for all this can usually be found as comments in the file /etc/sensors.conf Regards, Till Am Sonntag, 14. Januar 2007 23:01 schrieb Siju George: > Hi, > > could some one please help me interpret the output of sensors on two > servers I have? > They are running on Debian Sarge/amd64. The full sensors output of > both systems are given in the end of this mail. > > On System-1 I have the following lines. > > w83627hf-isa-0290 > Adapter: ISA adapter > VCore 1: +1.57 V (min = +1.86 V, max = +2.05 V) > VCore 2: +1.58 V (min = +1.86 V, max = +2.05 V) > +12V: +5.11 V (min = +10.82 V, max = +13.19 V) > -5V: -3.54 V (min = -5.25 V, max = -4.75 V) > V5SB: +5.75 V (min = +4.76 V, max = +5.24 V) > VBat: +0.06 V (min = +2.40 V, max = +3.60 V) > > these values seem to be out of the min/max limits. > Is this a serious problem? > How are the min/max values decided? Is it hardcoded somewhere? > Or should I refer some manuals and adjust the min/max values? > If so where can I find those manuals? > What does "V5SB" and "VBat" mean? > > Now, > > fan1: 6081 RPM (min = 0 RPM, div = 2) > fan2: 6250 RPM (min = 0 RPM, div = 2) > fan3: 0 RPM (min = 2812 RPM, div = 8) > > what does the "div=8" mean? > and the min value for fan3 is 2812. does it mean that it is mandatry > this fan should be running always above that RPM value? or is running > fan1 and fan2 enough? > > temp1: +33?C (high = +43?C, hyst = -1?C) sensor = thermistor > > What does "hyst=" mean? > > comming down for System-1 > > adm1027-i2c-0-2e > Adapter: SMBus AMD756 adapter at 10e0 > V1.5: +2.591 V (min = +1.42 V, max = +1.58 V) ALARM > VCore: +1.289 V (min = +1.71 V, max = +1.89 V) ALARM > > Shows it is in an ALARM state when the values fall out of the min/max > limits. In such a situation what can be done to rectify this? > why is not the "ALARM" keyword used when the values for w83627hf-isa-0290 > Adapter: ISA adapter fall out of the min/max range earlier? > > fan2: 17252 RPM (min = 0 RPM) > fan3: 0 RPM (min = 0 RPM) > fan4: 0 RPM (min = 0 RPM) > > counting the fan1, fan2 and fan3 shown earlier with differrent RPMs > Does this server have 6 fans? > I haven't seen this system because it is in a differrent continent :-( > > Board: +35.00?C (low = +10?C, high = +35?C) > Remote: +40.00?C (low = +10?C, high = +35?C) ALARM > > Board Temperature seems to be on the maximum limit. > Will running additional fan help to reduce the temperature? > What does "Remote:" mean ? Is it the Room temperature outside the chasis? > Also Just wondering how it is measured? Will not the temperature > inside the chasis influence its value? > > CPU_PWM: 255 > Fan2_PWM: 255 > Fan3_PWM: 255 > vid: +1.800 V (VRM Version 9.1) > > what does these values mean. Since there are no min/max values for > this what information can be gathered out of these? > > ######Comming to System-2######## > > w83627hf-isa-0290 > Adapter: ISA adapter > VCore 1: +0.00 V (min = +1.86 V, max = +2.05 V) > VCore 2: +1.54 V (min = +1.86 V, max = +2.05 V) > > What is VCore1 and VCore2? actually is there some resource where I can > learn more about related stufff? > > VCore 1: seems to be having no voltage at all! This Server runs > without much problems. > Can this be ignored? or how Do I rectify this situation? > > -12V: -1.26 V (min = -13.18 V, max = -10.80 V) > > the above value seems to be much greater than max value. > How do I rectify this? > > also what do the "+3.3V, +5V,+12V, -12V and -5V in the begining of the > following lines mean? > > +3.3V: +3.38 V (min = +3.14 V, max = +3.47 V) > +5V: +5.11 V (min = +4.76 V, max = +5.24 V) > +12V: +4.99 V (min = +10.82 V, max = +13.19 V) > -12V: -1.26 V (min = -13.18 V, max = -10.80 V) > -5V: -3.59 V (min = -5.25 V, max = -4.75 V) > > -------- > > again > > adm1027-i2c-0-2d > Adapter: SMBus AMD756 adapter at 10e0 > V1.5: +0.000 V (min = +1.42 V, max = +1.58 V) ALARM > VCore: +0.000 V (min = +0.00 V, max = +0.00 V) ALARM > > how do I rectify the above problem? > > CPU_Fan: 0 RPM (min = 4000 RPM) ALARM > > Does this man that the Fan above the CPU is not working at all? > > CPU: -128.00?C (low = +10?C, high = +50?C) ALARM FAULT > > What Does the "ALARM FAULT" mean in the above line? > Is it that the sensor is not working correctly? or some other problem? > Should I ask for a board replacement in this case? > > Remote: +33.00?C (low = +10?C, high = +35?C) ALARM > > the above value seems to be within the limits, then why is there an > "ALARM"? > > Thankyou so much for your patience :-) > If there is a link that will give me the information to these problems > please give it to me. > > Thankyou all once again :-) > > Kind Regards > > Siju > > ########################################################################## > System-1~# sensors > w83627hf-isa-0290 > Adapter: ISA adapter > VCore 1: +1.57 V (min = +1.86 V, max = +2.05 V) > VCore 2: +1.58 V (min = +1.86 V, max = +2.05 V) > +3.3V: +3.41 V (min = +3.14 V, max = +3.47 V) > +5V: +5.21 V (min = +4.76 V, max = +5.24 V) > +12V: +5.11 V (min = +10.82 V, max = +13.19 V) > -12V: -1.26 V (min = -13.18 V, max = -10.80 V) > -5V: -3.54 V (min = -5.25 V, max = -4.75 V) > V5SB: +5.75 V (min = +4.76 V, max = +5.24 V) > VBat: +0.06 V (min = +2.40 V, max = +3.60 V) > fan1: 6081 RPM (min = 0 RPM, div = 2) > fan2: 6250 RPM (min = 0 RPM, div = 2) > fan3: 0 RPM (min = 2812 RPM, div = 8) > temp1: +33?C (high = +43?C, hyst = -1?C) sensor = thermistor > > temp2: +34.5?C (high = +80?C, hyst = +75?C) sensor = thermistor > > temp3: +39.0?C (high = +80?C, hyst = +75?C) sensor = thermistor > > vid: +1.950 V (VRM Version 8.2) > alarms: > beep_enable: > Sound alarm disabled > > eeprom-i2c-0-55 > Adapter: SMBus AMD756 adapter at 10e0 > Memory type: DDR SDRAM DIMM > Memory size (MB): 1024 > > eeprom-i2c-0-54 > Adapter: SMBus AMD756 adapter at 10e0 > Memory type: DDR SDRAM DIMM > Memory size (MB): 1024 > > eeprom-i2c-0-51 > Adapter: SMBus AMD756 adapter at 10e0 > Memory type: DDR SDRAM DIMM > Memory size (MB): 1024 > > eeprom-i2c-0-50 > Adapter: SMBus AMD756 adapter at 10e0 > Memory type: DDR SDRAM DIMM > Memory size (MB): 1024 > > adm1027-i2c-0-2e > Adapter: SMBus AMD756 adapter at 10e0 > V1.5: +2.591 V (min = +1.42 V, max = +1.58 V) ALARM > VCore: +1.289 V (min = +1.71 V, max = +1.89 V) ALARM > V3.3: +3.334 V (min = +3.13 V, max = +3.47 V) > V5: +5.104 V (min = +4.74 V, max = +5.26 V) > V12: +12.125 V (min = +11.38 V, max = +12.62 V) > CPU_Fan: 17763 RPM (min = 4000 RPM) > fan2: 17252 RPM (min = 0 RPM) > fan3: 0 RPM (min = 0 RPM) > fan4: 0 RPM (min = 0 RPM) > CPU: +42.00?C (low = +10?C, high = +50?C) > Board: +35.00?C (low = +10?C, high = +35?C) > Remote: +40.00?C (low = +10?C, high = +35?C) ALARM > CPU_PWM: 255 > Fan2_PWM: 255 > Fan3_PWM: 255 > vid: +1.800 V (VRM Version 9.1) > ##################################################################### > System-2# sensors > w83627hf-isa-0290 > Adapter: ISA adapter > VCore 1: +0.00 V (min = +1.86 V, max = +2.05 V) > VCore 2: +1.54 V (min = +1.86 V, max = +2.05 V) > +3.3V: +3.38 V (min = +3.14 V, max = +3.47 V) > +5V: +5.11 V (min = +4.76 V, max = +5.24 V) > +12V: +4.99 V (min = +10.82 V, max = +13.19 V) > -12V: -1.26 V (min = -13.18 V, max = -10.80 V) > -5V: -3.59 V (min = -5.25 V, max = -4.75 V) > V5SB: +5.75 V (min = +4.76 V, max = +5.24 V) > VBat: +0.05 V (min = +2.40 V, max = +3.60 V) > fan1: 0 RPM (min = 0 RPM, div = 2) > fan2: 0 RPM (min = 0 RPM, div = 2) > fan3: 9642 RPM (min = 2860 RPM, div = 2) > temp1: +15?C (high = +11?C, hyst = -3?C) sensor = > thermistor > temp2: +14.5?C (high = +80?C, hyst = +75?C) sensor = > thermistor > temp3: +20.0?C (high = +80?C, hyst = +75?C) sensor = > thermistor > vid: +1.950 V (VRM Version 8.2) > alarms: > beep_enable: > Sound alarm disabled > > eeprom-i2c-0-51 > Adapter: SMBus AMD756 adapter at 10e0 > Memory type: DDR SDRAM DIMM > Memory size (MB): 1024 > > eeprom-i2c-0-50 > Adapter: SMBus AMD756 adapter at 10e0 > Memory type: DDR SDRAM DIMM > Memory size (MB): 1024 > > adm1027-i2c-0-2d > Adapter: SMBus AMD756 adapter at 10e0 > V1.5: +0.000 V (min = +1.42 V, max = +1.58 V) ALARM > VCore: +0.000 V (min = +0.00 V, max = +0.00 V) ALARM > V3.3: +3.317 V (min = +3.13 V, max = +3.47 V) > V5: +5.104 V (min = +4.74 V, max = +5.26 V) > V12: +12.125 V (min = +11.38 V, max = +12.62 V) > CPU_Fan: 0 RPM (min = 4000 RPM) ALARM > fan2: 0 RPM (min = 0 RPM) > fan3: 9747 RPM (min = 0 RPM) > fan4: 0 RPM (min = 0 RPM) > CPU: -128.00?C (low = +10?C, high = +50?C) ALARM FAULT > Board: +26.00?C (low = +10?C, high = +35?C) > Remote: +33.00?C (low = +10?C, high = +35?C) ALARM > CPU_PWM: 255 > Fan2_PWM: 255 > Fan3_PWM: 255 > vid: +0.000 V (VRM Version 9.1) > > ###################################################################### > > _______________________________________________ > lm-sensors mailing list > lm-sensors at lm-sensors.org > http://lists.lm-sensors.org/mailman/listinfo/lm-sensors
