On Sat, 02 Dec 2006 09:16:32 -0500, MC Castle wrote: > 1)I could not get your Wiki to work, so maybe someone could post this in > event I'm not the only person with a NF-M2. > 2) You instructions for installing lm-sensors suggests removing files > from /usr/lib. This breaks KSysGuard. Which instructions? > > #============================================ > # ABIT NF-M2 > # > # MC Castle, Castle Engineering Services, LLC > # 02 Dec 2006: Initial conf for ABIT NF-M2 > # > #============================================ > > #**************************************** > chip "k8temp-*" > # k8temp-i2c--5-c3 Strange string, "sensors" doesn't actually display this, does it? > # Adapter: PCI adapter > #**************************************** > > label temp1 "Core 0" > ignore temp2 > label temp3 "Core 1" > ignore temp4 > > #**************************************** > chip "w83627ehf-*" > # w83627ehf-isa-0290 > # Adapter: ISA adapter > > # From ABITEQ: Factor = (R2/(R1+R2))*1000 > # Not sure of VAVCC & VSB > #**************************************** > > label in0 "VCore" #VCORE Index 0x20, Bank 0, Factor = 1000 > label in1 "DDR2 V" #VIN0 Index 0x21, Bank 0, Factor = 500 > label in2 "VAVCC?" #VAVCC Index 0x22, Bank 0, Factor = ? > ignore in2 > label in3 "ATX +3.3V" #V3VCC Index 0x23, Bank 0, Factor = 1000 > label in4 "DDR VTT" #VIN1 Index 0x24, Bank 0, Factor = > 1000 > label in5 "CS Core" #VIN2 Index 0x25, Bank 0, Factor = > 1000 > label in6 "ATX +12V" #VIN3 Index 0x26, Bank 0, Factor = 131 > label in7 "VSB?" #VSB Index 0x50, Bank 5, Factor = ? > ignore in7 > label in8 "VBAT" #VBAT Index 0x51, Bank 5, Factor = ? > label in9 "ATX +5V" #VIN4 Index 0x52, Bank 5, Factor = 333 > > label temp1 "Case Temp" #SYSTIN Index 0x27, Bank 0 > label temp2 "CPU Temp" #CPUTIN Index 0x50, Bank 1 > label temp3 "PWM Temp" #AUXTIN Index 0x50, Bank 2 > > label fan1 "SYS Fan" #SYSFANIN Index 0x28, Bank 0 > label fan2 "CPU Fan" #CPUFANIN0 Index 0x29, Bank 0 > label fan3 "AUX1 Fan" #AUXFANIN0 Index 0x2a, Bank 0 > label fan4 "Aux2 Fan" #CPUFANIN1 Index 0x3f, Bank 0 > label fan5 "Aux3 Fan" #AUXFANIN1 Index 0x53, Bank 5 > > #--------------------------------------------------------------------------- > > # commented out Factor = 1000 (read direct entries) > > # compute in0 (1000/1000)*@, @/(1000/1000) # F = 1000 > compute in1 (1000/500)*@, @/(1000/500) # F = 500 > # compute in2 (1000/x)*@, @/(1000/x) # F = ? > # compute in3 (1000/1000)*@, @/(1000/1000) # F = 1000 > # compute in4 (1000/1000)*@, @/(1000/1000) # F = 1000 > # compute in5 (1000/1000)*@, @/(1000/1000) # F = 1000 > compute in6 (1000/131)*@, @/(1000/131) # F = 131 > # compute in7 (1000/x)*@, @/(1000/x) # F = ? > # compute in8 (1000/x)*@, @/(1000/x) # F = ? > compute in9 (1000/333)*@, @/(1000/333) # F = 333 > > #--------------------------------------------------------------------------- > > # set limits to 5% for the critical voltages > # set limits to 10% for the non-critical voltages > # set limits to 20% for the battery voltage > > set in0_min 1.35*0.95 > set in0_max 1.35*1.05 > set in1_min 1.8*0.95 > set in1_max 1.8*1.05 > set in2_min 3.3 * 0.95 > set in2_max 3.3 * 1.05 > set in3_min 3.3 * 0.95 > set in3_max 3.3 * 1.05 > set in4_min 0.9 * 0.95 > set in4_max 0.9 * 1.05 > set in5_min 1.2 * 0.95 > set in5_max 1.2 * 1.05 > set in6_min 12.0 * 0.95 > set in6_max 12.0 * 1.05 > set in7_min 3.3 * 0.90 > set in7_max 3.3 * 1.10 > set in8_min 3.0 * 0.80 > set in8_max 3.0 * 1.20 > set in9_min 5.0 * 0.95 > set in9_max 5.0 * 1.05 > > set fan1_min 2000 > set fan2_min 2000 > > set temp1_over 50 > set temp1_hyst 45 > set temp2_over 65 > set temp2_hyst 60 > set temp3_over 70 > set temp3_hyst 65 > > #--------------------------------------------------------------------------- > -- Jean Delvare
