This is a note to let you know that I've just added the patch titled
Subject: [PATCH 3/6] hwmon: Fix documentation typos
to my gregkh-2.6 tree. Its filename is
hwmon-documentation-typos.patch
This tree can be found at
http://www.kernel.org/pub/linux/kernel/people/gregkh/gregkh-2.6/patches/
>From khali at linux-fr.org Sun Oct 8 12:59:58 2006
Date: Sun, 8 Oct 2006 21:59:54 +0200
From: Jean Delvare <khali at linux-fr.org>
To: Greg KH <greg at kroah.com>
Cc: LM Sensors <lm-sensors at lm-sensors.org>
Subject: [PATCH 3/6] hwmon: Fix documentation typos
Message-Id: <20061008215954.3a00c185.khali at linux-fr.org>
Content-Disposition: inline; filename=hwmon-documentation-typos.patch
Fix typos in hardware monitoring documentation.
Signed-off-by: Jean Delvare <khali at linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh at suse.de>
---
Documentation/hwmon/f71805f | 2 +-
Documentation/hwmon/w83627ehf | 6 +++---
2 files changed, 4 insertions(+), 4 deletions(-)
--- gregkh-2.6.orig/Documentation/hwmon/f71805f
+++ gregkh-2.6/Documentation/hwmon/f71805f
@@ -17,7 +17,7 @@ Thanks to Kris Chen from Fintek for answ
providing additional documentation.
Thanks to Chris Lin from Jetway for providing wiring schematics and
-anwsering technical questions.
+answering technical questions.
Description
--- gregkh-2.6.orig/Documentation/hwmon/w83627ehf
+++ gregkh-2.6/Documentation/hwmon/w83627ehf
@@ -26,7 +26,7 @@ fan control mode).
Temperatures are measured in degrees Celsius and measurement resolution is 1
degC for temp1 and 0.5 degC for temp2 and temp3. An alarm is triggered when
the temperature gets higher than high limit; it stays on until the temperature
-falls below the Hysteresis value.
+falls below the hysteresis value.
Fan rotation speeds are reported in RPM (rotations per minute). An alarm is
triggered if the rotation speed has dropped below a programmable limit. Fan
@@ -67,9 +67,9 @@ Thermal Cruise mode
If the temperature is in the range defined by:
-pwm[1-4]_target - set target temperature, unit millidegree Celcius
+pwm[1-4]_target - set target temperature, unit millidegree Celsius
(range 0 - 127000)
-pwm[1-4]_tolerance - tolerance, unit millidegree Celcius (range 0 - 15000)
+pwm[1-4]_tolerance - tolerance, unit millidegree Celsius (range 0 - 15000)
there are no changes to fan speed. Once the temperature leaves the interval,
fan speed increases (temp is higher) or decreases if lower than desired.
Patches currently in gregkh-2.6 which might be from khali at linux-fr.org are
i2c/hwmon-documentation-typos.patch
i2c/hwmon-k8temp-documentation-update.patch
i2c/hwmon-smsc47m112-documentation.patch
i2c/hwmon-unchecked-return-status-fixes-w83791d.patch
i2c/hwmon-update-Grant-Coady-email-address.patch
i2c/hwmon-w83627ehf-fix-fan5-detection.patch
driver-class/i2c-dev-device.patch
driver-class/i2c-dev-device.old.patch
