From: Hartmut Rick <linux at rick.claranet.de> New driver (smsc47m192) which supports voltage and temperature measurement features of SMSC LPC47M192 and LPC47M997 chips. Signed-off-by: Hartmut Rick <linux at rick.claranet.de> Signed-off-by: Jean Delvare <khali at linux-fr.org> Signed-off-by: Greg Kroah-Hartman <gregkh at suse.de> --- Documentation/hwmon/smsc47m192 | 102 ++++++ Documentation/hwmon/sysfs-interface | 6 drivers/hwmon/Kconfig | 23 + drivers/hwmon/Makefile | 1 drivers/hwmon/smsc47m192.c | 648 +++++++++++++++++++++++++++++++++++ 5 files changed, 779 insertions(+), 1 deletions(-) diff --git a/Documentation/hwmon/smsc47m192 b/Documentation/hwmon/smsc47m192 new file mode 100644 index 0000000..45d6453 --- /dev/null +++ b/Documentation/hwmon/smsc47m192 @@ -0,0 +1,102 @@ +Kernel driver smsc47m192 +======================== + +Supported chips: + * SMSC LPC47M192 and LPC47M997 + Prefix: 'smsc47m192' + Addresses scanned: I2C 0x2c - 0x2d + Datasheet: The datasheet for LPC47M192 is publicly available from + http://www.smsc.com/ + The LPC47M997 is compatible for hardware monitoring. + +Author: Hartmut Rick <linux at rick.claranet.de> + Special thanks to Jean Delvare for careful checking + of the code and many helpful comments and suggestions. + + +Description +----------- + +This driver implements support for the hardware sensor capabilities +of the SMSC LPC47M192 and LPC47M997 Super-I/O chips. + +These chips support 3 temperature channels and 8 voltage inputs +as well as CPU voltage VID input. + +They do also have fan monitoring and control capabilities, but the +these features are accessed via ISA bus and are not supported by this +driver. Use the 'smsc47m1' driver for fan monitoring and control. + +Voltages and temperatures are measured by an 8-bit ADC, the resolution +of the temperatures is 1 bit per degree C. +Voltages are scaled such that the nominal voltage corresponds to +192 counts, i.e. 3/4 of the full range. Thus the available range for +each voltage channel is 0V ... 255/192*(nominal voltage), the resolution +is 1 bit per (nominal voltage)/192. +Both voltage and temperature values are scaled by 1000, the sys files +show voltages in mV and temperatures in units of 0.001 degC. + +The +12V analog voltage input channel (in4_input) is multiplexed with +bit 4 of the encoded CPU voltage. This means that you either get +a +12V voltage measurement or a 5 bit CPU VID, but not both. +The default setting is to use the pin as 12V input, and use only 4 bit VID. +This driver assumes that the information in the configuration register +is correct, i.e. that the BIOS has updated the configuration if +the motherboard has this input wired to VID4. + +The temperature and voltage readings are updated once every 1.5 seconds. +Reading them more often repeats the same values. + + +sysfs interface +--------------- + +in0_input - +2.5V voltage input +in1_input - CPU voltage input (nominal 2.25V) +in2_input - +3.3V voltage input +in3_input - +5V voltage input +in4_input - +12V voltage input (may be missing if used as VID4) +in5_input - Vcc voltage input (nominal 3.3V) + This is the supply voltage of the sensor chip itself. +in6_input - +1.5V voltage input +in7_input - +1.8V voltage input + +in[0-7]_min, +in[0-7]_max - lower and upper alarm thresholds for in[0-7]_input reading + + All voltages are read and written in mV. + +in[0-7]_alarm - alarm flags for voltage inputs + These files read '1' in case of alarm, '0' otherwise. + +temp1_input - chip temperature measured by on-chip diode +temp[2-3]_input - temperature measured by external diodes (one of these would + typically be wired to the diode inside the CPU) + +temp[1-3]_min, +temp[1-3]_max - lower and upper alarm thresholds for temperatures + +temp[1-3]_offset - temperature offset registers + The chip adds the offsets stored in these registers to + the corresponding temperature readings. + Note that temp1 and temp2 offsets share the same register, + they cannot both be different from zero at the same time. + Writing a non-zero number to one of them will reset the other + offset to zero. + + All temperatures and offsets are read and written in + units of 0.001 degC. + +temp[1-3]_alarm - alarm flags for temperature inputs, '1' in case of alarm, + '0' otherwise. +temp[2-3]_input_fault - diode fault flags for temperature inputs 2 and 3. + A fault is detected if the two pins for the corresponding + sensor are open or shorted, or any of the two is shorted + to ground or Vcc. '1' indicates a diode fault. + +cpu0_vid - CPU voltage as received from the CPU + +vrm - CPU VID standard used for decoding CPU voltage + + The *_min, *_max, *_offset and vrm files can be read and + written, all others are read-only. diff --git a/Documentation/hwmon/sysfs-interface b/Documentation/hwmon/sysfs-interface index a0d0ab2..2d16e1e 100644 --- a/Documentation/hwmon/sysfs-interface +++ b/Documentation/hwmon/sysfs-interface @@ -218,6 +218,12 @@ temp[1-2]_crit_hyst from the critical value. Read/Write value. +temp[1-4]_offset + Temperature offset which is added to the temperature reading + by the chip. + Unit: millidegree Celsius + Read/Write value. + If there are multiple temperature sensors, temp1_* is generally the sensor inside the chip itself, reported as "motherboard temperature". temp2_* to diff --git a/drivers/hwmon/Kconfig b/drivers/hwmon/Kconfig index a6a8d66..9cf3d9c 100644 --- a/drivers/hwmon/Kconfig +++ b/drivers/hwmon/Kconfig @@ -333,11 +333,32 @@ config SENSORS_SMSC47M1 help If you say yes here you get support for the integrated fan monitoring and control capabilities of the SMSC LPC47B27x, - LPC47M10x, LPC47M13x, LPC47M14x, LPC47M15x and LPC47M192 chips. + LPC47M10x, LPC47M13x, LPC47M14x, LPC47M15x, LPC47M192 and + LPC47M997 chips. + + The temperature and voltage sensor features of the LPC47M192 + and LPC47M997 are supported by another driver, select also + "SMSC LPC47M192 and compatibles" below for those. This driver can also be built as a module. If so, the module will be called smsc47m1. +config SENSORS_SMSC47M192 + tristate "SMSC LPC47M192 and compatibles" + depends on HWMON && I2C && EXPERIMENTAL + select HWMON_VID + help + If you say yes here you get support for the temperature and + voltage sensors of the SMSC LPC47M192 and LPC47M997 chips. + + The fan monitoring and control capabilities of these chips + are supported by another driver, select + "SMSC LPC47M10x and compatibles" above. You need both drivers + if you want fan control and voltage/temperature sensor support. + + This driver can also be built as a module. If so, the module + will be called smsc47m192. + config SENSORS_SMSC47B397 tristate "SMSC LPC47B397-NC" depends on HWMON && I2C && EXPERIMENTAL diff --git a/drivers/hwmon/Makefile b/drivers/hwmon/Makefile index fbdb8d9..d090459 100644 --- a/drivers/hwmon/Makefile +++ b/drivers/hwmon/Makefile @@ -40,6 +40,7 @@ obj-$(CONFIG_SENSORS_PC87360) += pc87360 obj-$(CONFIG_SENSORS_SIS5595) += sis5595.o obj-$(CONFIG_SENSORS_SMSC47B397)+= smsc47b397.o obj-$(CONFIG_SENSORS_SMSC47M1) += smsc47m1.o +obj-$(CONFIG_SENSORS_SMSC47M192)+= smsc47m192.o obj-$(CONFIG_SENSORS_VIA686A) += via686a.o obj-$(CONFIG_SENSORS_VT8231) += vt8231.o obj-$(CONFIG_SENSORS_W83627EHF) += w83627ehf.o diff --git a/drivers/hwmon/smsc47m192.c b/drivers/hwmon/smsc47m192.c new file mode 100644 index 0000000..bdc4570 --- /dev/null +++ b/drivers/hwmon/smsc47m192.c @@ -0,0 +1,648 @@ +/* + smsc47m192.c - Support for hardware monitoring block of + SMSC LPC47M192 and LPC47M997 Super I/O chips + + Copyright (C) 2006 Hartmut Rick <linux at rick.claranet.de> + + Derived from lm78.c and other chip drivers. + + This program is free software; you can redistribute it and/or modify + it under the terms of the GNU General Public License as published by + the Free Software Foundation; either version 2 of the License, or + (at your option) any later version. + + This program is distributed in the hope that it will be useful, + but WITHOUT ANY WARRANTY; without even the implied warranty of + MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + GNU General Public License for more details. + + You should have received a copy of the GNU General Public License + along with this program; if not, write to the Free Software + Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA. +*/ + +#include <linux/module.h> +#include <linux/init.h> +#include <linux/slab.h> +#include <linux/jiffies.h> +#include <linux/i2c.h> +#include <linux/hwmon.h> +#include <linux/hwmon-sysfs.h> +#include <linux/hwmon-vid.h> +#include <linux/err.h> + +/* Addresses to scan */ +static unsigned short normal_i2c[] = { 0x2c, 0x2d, I2C_CLIENT_END }; + +/* Insmod parameters */ +I2C_CLIENT_INSMOD_1(smsc47m192); + +/* SMSC47M192 registers */ +#define SMSC47M192_REG_IN(nr) ((nr)<6 ? (0x20 + (nr)) : \ + (0x50 + (nr) - 6)) +#define SMSC47M192_REG_IN_MAX(nr) ((nr)<6 ? (0x2b + (nr) * 2) : \ + (0x54 + (((nr) - 6) * 2))) +#define SMSC47M192_REG_IN_MIN(nr) ((nr)<6 ? (0x2c + (nr) * 2) : \ + (0x55 + (((nr) - 6) * 2))) +static u8 SMSC47M192_REG_TEMP[3] = { 0x27, 0x26, 0x52 }; +static u8 SMSC47M192_REG_TEMP_MAX[3] = { 0x39, 0x37, 0x58 }; +static u8 SMSC47M192_REG_TEMP_MIN[3] = { 0x3A, 0x38, 0x59 }; +#define SMSC47M192_REG_TEMP_OFFSET(nr) ((nr)==2 ? 0x1e : 0x1f) +#define SMSC47M192_REG_ALARM1 0x41 +#define SMSC47M192_REG_ALARM2 0x42 +#define SMSC47M192_REG_VID 0x47 +#define SMSC47M192_REG_VID4 0x49 +#define SMSC47M192_REG_CONFIG 0x40 +#define SMSC47M192_REG_SFR 0x4f +#define SMSC47M192_REG_COMPANY_ID 0x3e +#define SMSC47M192_REG_VERSION 0x3f + +/* generalised scaling with integer rounding */ +static inline int SCALE(long val, int mul, int div) +{ + if (val < 0) + return (val * mul - div / 2) / div; + else + return (val * mul + div / 2) / div; +} + +/* Conversions */ + +/* smsc47m192 internally scales voltage measurements */ +static const u16 nom_mv[] = { 2500, 2250, 3300, 5000, 12000, 3300, 1500, 1800 }; + +static inline unsigned int IN_FROM_REG(u8 reg, int n) +{ + return SCALE(reg, nom_mv[n], 192); +} + +static inline u8 IN_TO_REG(unsigned long val, int n) +{ + return SENSORS_LIMIT(SCALE(val, 192, nom_mv[n]), 0, 255); +} + +/* TEMP: 0.001 degC units (-128C to +127C) + REG: 1C/bit, two's complement */ +static inline s8 TEMP_TO_REG(int val) +{ + return SENSORS_LIMIT(SCALE(val, 1, 1000), -128000, 127000); +} + +static inline int TEMP_FROM_REG(s8 val) +{ + return val * 1000; +} + +struct smsc47m192_data { + struct i2c_client client; + struct class_device *class_dev; + struct semaphore update_lock; + char valid; /* !=0 if following fields are valid */ + unsigned long last_updated; /* In jiffies */ + + u8 in[8]; /* Register value */ + u8 in_max[8]; /* Register value */ + u8 in_min[8]; /* Register value */ + s8 temp[3]; /* Register value */ + s8 temp_max[3]; /* Register value */ + s8 temp_min[3]; /* Register value */ + s8 temp_offset[3]; /* Register value */ + u16 alarms; /* Register encoding, combined */ + u8 vid; /* Register encoding, combined */ + u8 vrm; +}; + +static int smsc47m192_attach_adapter(struct i2c_adapter *adapter); +static int smsc47m192_detect(struct i2c_adapter *adapter, int address, + int kind); +static int smsc47m192_detach_client(struct i2c_client *client); +static struct smsc47m192_data *smsc47m192_update_device(struct device *dev); + +static struct i2c_driver smsc47m192_driver = { + .driver = { + .name = "smsc47m192", + }, + .attach_adapter = smsc47m192_attach_adapter, + .detach_client = smsc47m192_detach_client, +}; + +/* Voltages */ +static ssize_t show_in(struct device *dev, struct device_attribute *attr, + char *buf) +{ + struct sensor_device_attribute *sensor_attr = to_sensor_dev_attr(attr); + int nr = sensor_attr->index; + struct smsc47m192_data *data = smsc47m192_update_device(dev); + return sprintf(buf, "%d\n", IN_FROM_REG(data->in[nr], nr)); +} + +static ssize_t show_in_min(struct device *dev, struct device_attribute *attr, + char *buf) +{ + struct sensor_device_attribute *sensor_attr = to_sensor_dev_attr(attr); + int nr = sensor_attr->index; + struct smsc47m192_data *data = smsc47m192_update_device(dev); + return sprintf(buf, "%d\n", IN_FROM_REG(data->in_min[nr], nr)); +} + +static ssize_t show_in_max(struct device *dev, struct device_attribute *attr, + char *buf) +{ + struct sensor_device_attribute *sensor_attr = to_sensor_dev_attr(attr); + int nr = sensor_attr->index; + struct smsc47m192_data *data = smsc47m192_update_device(dev); + return sprintf(buf, "%d\n", IN_FROM_REG(data->in_max[nr], nr)); +} + +static ssize_t set_in_min(struct device *dev, struct device_attribute *attr, + const char *buf, size_t count) +{ + struct sensor_device_attribute *sensor_attr = to_sensor_dev_attr(attr); + int nr = sensor_attr->index; + struct i2c_client *client = to_i2c_client(dev); + struct smsc47m192_data *data = i2c_get_clientdata(client); + unsigned long val = simple_strtoul(buf, NULL, 10); + + down(&data->update_lock); + data->in_min[nr] = IN_TO_REG(val, nr); + i2c_smbus_write_byte_data(client, SMSC47M192_REG_IN_MIN(nr), + data->in_min[nr]); + up(&data->update_lock); + return count; +} + +static ssize_t set_in_max(struct device *dev, struct device_attribute *attr, + const char *buf, size_t count) +{ + struct sensor_device_attribute *sensor_attr = to_sensor_dev_attr(attr); + int nr = sensor_attr->index; + struct i2c_client *client = to_i2c_client(dev); + struct smsc47m192_data *data = i2c_get_clientdata(client); + unsigned long val = simple_strtoul(buf, NULL, 10); + + down(&data->update_lock); + data->in_max[nr] = IN_TO_REG(val, nr); + i2c_smbus_write_byte_data(client, SMSC47M192_REG_IN_MAX(nr), + data->in_max[nr]); + up(&data->update_lock); + return count; +} + +#define show_in_offset(offset) \ +static SENSOR_DEVICE_ATTR(in##offset##_input, S_IRUGO, \ + show_in, NULL, offset); \ +static SENSOR_DEVICE_ATTR(in##offset##_min, S_IRUGO | S_IWUSR, \ + show_in_min, set_in_min, offset); \ +static SENSOR_DEVICE_ATTR(in##offset##_max, S_IRUGO | S_IWUSR, \ + show_in_max, set_in_max, offset); + +show_in_offset(0) +show_in_offset(1) +show_in_offset(2) +show_in_offset(3) +show_in_offset(4) +show_in_offset(5) +show_in_offset(6) +show_in_offset(7) + +/* Temperatures */ +static ssize_t show_temp(struct device *dev, struct device_attribute *attr, + char *buf) +{ + struct sensor_device_attribute *sensor_attr = to_sensor_dev_attr(attr); + int nr = sensor_attr->index; + struct smsc47m192_data *data = smsc47m192_update_device(dev); + return sprintf(buf, "%d\n", TEMP_FROM_REG(data->temp[nr])); +} + +static ssize_t show_temp_min(struct device *dev, struct device_attribute *attr, + char *buf) +{ + struct sensor_device_attribute *sensor_attr = to_sensor_dev_attr(attr); + int nr = sensor_attr->index; + struct smsc47m192_data *data = smsc47m192_update_device(dev); + return sprintf(buf, "%d\n", TEMP_FROM_REG(data->temp_min[nr])); +} + +static ssize_t show_temp_max(struct device *dev, struct device_attribute *attr, + char *buf) +{ + struct sensor_device_attribute *sensor_attr = to_sensor_dev_attr(attr); + int nr = sensor_attr->index; + struct smsc47m192_data *data = smsc47m192_update_device(dev); + return sprintf(buf, "%d\n", TEMP_FROM_REG(data->temp_max[nr])); +} + +static ssize_t set_temp_min(struct device *dev, struct device_attribute *attr, + const char *buf, size_t count) +{ + struct sensor_device_attribute *sensor_attr = to_sensor_dev_attr(attr); + int nr = sensor_attr->index; + struct i2c_client *client = to_i2c_client(dev); + struct smsc47m192_data *data = i2c_get_clientdata(client); + long val = simple_strtol(buf, NULL, 10); + + down(&data->update_lock); + data->temp_min[nr] = TEMP_TO_REG(val); + i2c_smbus_write_byte_data(client, SMSC47M192_REG_TEMP_MIN[nr], + data->temp_min[nr]); + up(&data->update_lock); + return count; +} + +static ssize_t set_temp_max(struct device *dev, struct device_attribute *attr, + const char *buf, size_t count) +{ + struct sensor_device_attribute *sensor_attr = to_sensor_dev_attr(attr); + int nr = sensor_attr->index; + struct i2c_client *client = to_i2c_client(dev); + struct smsc47m192_data *data = i2c_get_clientdata(client); + long val = simple_strtol(buf, NULL, 10); + + down(&data->update_lock); + data->temp_max[nr] = TEMP_TO_REG(val); + i2c_smbus_write_byte_data(client, SMSC47M192_REG_TEMP_MAX[nr], + data->temp_max[nr]); + up(&data->update_lock); + return count; +} + +static ssize_t show_temp_offset(struct device *dev, struct device_attribute + *attr, char *buf) +{ + struct sensor_device_attribute *sensor_attr = to_sensor_dev_attr(attr); + int nr = sensor_attr->index; + struct smsc47m192_data *data = smsc47m192_update_device(dev); + return sprintf(buf, "%d\n", TEMP_FROM_REG(data->temp_offset[nr])); +} + +static ssize_t set_temp_offset(struct device *dev, struct device_attribute + *attr, const char *buf, size_t count) +{ + struct sensor_device_attribute *sensor_attr = to_sensor_dev_attr(attr); + int nr = sensor_attr->index; + struct i2c_client *client = to_i2c_client(dev); + struct smsc47m192_data *data = i2c_get_clientdata(client); + u8 sfr = i2c_smbus_read_byte_data(client, SMSC47M192_REG_SFR); + long val = simple_strtol(buf, NULL, 10); + + down(&data->update_lock); + data->temp_offset[nr] = TEMP_TO_REG(val); + if (nr>1) + i2c_smbus_write_byte_data(client, + SMSC47M192_REG_TEMP_OFFSET(nr), data->temp_offset[nr]); + else if (data->temp_offset[nr] != 0) { + /* offset[0] and offset[1] share the same register, + SFR bit 4 activates offset[0] */ + i2c_smbus_write_byte_data(client, SMSC47M192_REG_SFR, + (sfr & 0xef) | (nr==0 ? 0x10 : 0)); + data->temp_offset[1-nr] = 0; + i2c_smbus_write_byte_data(client, + SMSC47M192_REG_TEMP_OFFSET(nr), data->temp_offset[nr]); + } else if ((sfr & 0x10) == (nr==0 ? 0x10 : 0)) + i2c_smbus_write_byte_data(client, + SMSC47M192_REG_TEMP_OFFSET(nr), 0); + up(&data->update_lock); + return count; +} + +#define show_temp_index(index) \ +static SENSOR_DEVICE_ATTR(temp##index##_input, S_IRUGO, \ + show_temp, NULL, index-1); \ +static SENSOR_DEVICE_ATTR(temp##index##_min, S_IRUGO | S_IWUSR, \ + show_temp_min, set_temp_min, index-1); \ +static SENSOR_DEVICE_ATTR(temp##index##_max, S_IRUGO | S_IWUSR, \ + show_temp_max, set_temp_max, index-1); \ +static SENSOR_DEVICE_ATTR(temp##index##_offset, S_IRUGO | S_IWUSR, \ + show_temp_offset, set_temp_offset, index-1); + +show_temp_index(1) +show_temp_index(2) +show_temp_index(3) + +/* VID */ +static ssize_t show_vid(struct device *dev, struct device_attribute *attr, + char *buf) +{ + struct smsc47m192_data *data = smsc47m192_update_device(dev); + return sprintf(buf, "%d\n", vid_from_reg(data->vid, data->vrm)); +} +static DEVICE_ATTR(cpu0_vid, S_IRUGO, show_vid, NULL); + +static ssize_t show_vrm(struct device *dev, struct device_attribute *attr, + char *buf) +{ + struct smsc47m192_data *data = smsc47m192_update_device(dev); + return sprintf(buf, "%d\n", data->vrm); +} + +static ssize_t set_vrm(struct device *dev, struct device_attribute *attr, + const char *buf, size_t count) +{ + struct i2c_client *client = to_i2c_client(dev); + struct smsc47m192_data *data = i2c_get_clientdata(client); + data->vrm = simple_strtoul(buf, NULL, 10); + return count; +} +static DEVICE_ATTR(vrm, S_IRUGO | S_IWUSR, show_vrm, set_vrm); + +/* Alarms */ +static ssize_t show_alarm(struct device *dev, struct device_attribute *attr, + char *buf) +{ + struct sensor_device_attribute *sensor_attr = to_sensor_dev_attr(attr); + int nr = sensor_attr->index; + struct smsc47m192_data *data = smsc47m192_update_device(dev); + return sprintf(buf, "%u\n", (data->alarms & nr) ? 1 : 0); +} + +static SENSOR_DEVICE_ATTR(temp1_alarm, S_IRUGO, show_alarm, NULL, 0x0010); +static SENSOR_DEVICE_ATTR(temp2_alarm, S_IRUGO, show_alarm, NULL, 0x0020); +static SENSOR_DEVICE_ATTR(temp3_alarm, S_IRUGO, show_alarm, NULL, 0x0040); +static SENSOR_DEVICE_ATTR(temp2_input_fault, S_IRUGO, show_alarm, NULL, 0x4000); +static SENSOR_DEVICE_ATTR(temp3_input_fault, S_IRUGO, show_alarm, NULL, 0x8000); +static SENSOR_DEVICE_ATTR(in0_alarm, S_IRUGO, show_alarm, NULL, 0x0001); +static SENSOR_DEVICE_ATTR(in1_alarm, S_IRUGO, show_alarm, NULL, 0x0002); +static SENSOR_DEVICE_ATTR(in2_alarm, S_IRUGO, show_alarm, NULL, 0x0004); +static SENSOR_DEVICE_ATTR(in3_alarm, S_IRUGO, show_alarm, NULL, 0x0008); +static SENSOR_DEVICE_ATTR(in4_alarm, S_IRUGO, show_alarm, NULL, 0x0100); +static SENSOR_DEVICE_ATTR(in5_alarm, S_IRUGO, show_alarm, NULL, 0x0200); +static SENSOR_DEVICE_ATTR(in6_alarm, S_IRUGO, show_alarm, NULL, 0x0400); +static SENSOR_DEVICE_ATTR(in7_alarm, S_IRUGO, show_alarm, NULL, 0x0800); + +/* This function is called when: + * smsc47m192_driver is inserted (when this module is loaded), for each + available adapter + * when a new adapter is inserted (and smsc47m192_driver is still present) */ +static int smsc47m192_attach_adapter(struct i2c_adapter *adapter) +{ + if (!(adapter->class & I2C_CLASS_HWMON)) + return 0; + return i2c_probe(adapter, &addr_data, smsc47m192_detect); +} + +static void smsc47m192_init_client(struct i2c_client *client) +{ + int i; + u8 config = i2c_smbus_read_byte_data(client, SMSC47M192_REG_CONFIG); + u8 sfr = i2c_smbus_read_byte_data(client, SMSC47M192_REG_SFR); + + /* select cycle mode (pause 1 sec between updates) */ + i2c_smbus_write_byte_data(client, SMSC47M192_REG_SFR, + (sfr & 0xfd) | 0x02); + if (!(config & 0x01)) { + /* initialize alarm limits */ + for (i=0; i<8; i++) { + i2c_smbus_write_byte_data(client, + SMSC47M192_REG_IN_MIN(i), 0); + i2c_smbus_write_byte_data(client, + SMSC47M192_REG_IN_MAX(i), 0xff); + } + for (i=0; i<3; i++) { + i2c_smbus_write_byte_data(client, + SMSC47M192_REG_TEMP_MIN[i], 0x80); + i2c_smbus_write_byte_data(client, + SMSC47M192_REG_TEMP_MAX[i], 0x7f); + } + + /* start monitoring */ + i2c_smbus_write_byte_data(client, SMSC47M192_REG_CONFIG, + (config & 0xf7) | 0x01); + } +} + +/* This function is called by i2c_probe */ +static int smsc47m192_detect(struct i2c_adapter *adapter, int address, + int kind) +{ + struct i2c_client *client; + struct smsc47m192_data *data; + int err = 0; + int version, config; + + if (!i2c_check_functionality(adapter, I2C_FUNC_SMBUS_BYTE_DATA)) + goto exit; + + if (!(data = kzalloc(sizeof(struct smsc47m192_data), GFP_KERNEL))) { + err = -ENOMEM; + goto exit; + } + + client = &data->client; + i2c_set_clientdata(client, data); + client->addr = address; + client->adapter = adapter; + client->driver = &smsc47m192_driver; + + if (kind == 0) + kind = smsc47m192; + + /* Detection criteria from sensors_detect script */ + if (kind < 0) { + if (i2c_smbus_read_byte_data(client, + SMSC47M192_REG_COMPANY_ID) == 0x55 + && ((version = i2c_smbus_read_byte_data(client, + SMSC47M192_REG_VERSION)) & 0xf0) == 0x20 + && (i2c_smbus_read_byte_data(client, + SMSC47M192_REG_VID) & 0x70) == 0x00 + && (i2c_smbus_read_byte_data(client, + SMSC47M192_REG_VID4) & 0xfe) == 0x80) { + dev_info(&adapter->dev, + "found SMSC47M192 or SMSC47M997, " + "version 2, stepping A%d\n", version & 0x0f); + } else { + dev_dbg(&adapter->dev, + "SMSC47M192 detection failed at 0x%02x\n", + address); + goto exit_free; + } + } + + /* Fill in the remaining client fields and put into the global list */ + strlcpy(client->name, "smsc47m192", I2C_NAME_SIZE); + data->vrm = vid_which_vrm(); + init_MUTEX(&data->update_lock); + + /* Tell the I2C layer a new client has arrived */ + if ((err = i2c_attach_client(client))) + goto exit_free; + + /* Initialize the SMSC47M192 chip */ + smsc47m192_init_client(client); + + /* Register sysfs hooks */ + data->class_dev = hwmon_device_register(&client->dev); + if (IS_ERR(data->class_dev)) { + err = PTR_ERR(data->class_dev); + goto exit_detach; + } + + device_create_file(&client->dev, &sensor_dev_attr_in0_input.dev_attr); + device_create_file(&client->dev, &sensor_dev_attr_in0_min.dev_attr); + device_create_file(&client->dev, &sensor_dev_attr_in0_max.dev_attr); + device_create_file(&client->dev, &sensor_dev_attr_in0_alarm.dev_attr); + device_create_file(&client->dev, &sensor_dev_attr_in1_input.dev_attr); + device_create_file(&client->dev, &sensor_dev_attr_in1_min.dev_attr); + device_create_file(&client->dev, &sensor_dev_attr_in1_max.dev_attr); + device_create_file(&client->dev, &sensor_dev_attr_in1_alarm.dev_attr); + device_create_file(&client->dev, &sensor_dev_attr_in2_input.dev_attr); + device_create_file(&client->dev, &sensor_dev_attr_in2_min.dev_attr); + device_create_file(&client->dev, &sensor_dev_attr_in2_max.dev_attr); + device_create_file(&client->dev, &sensor_dev_attr_in2_alarm.dev_attr); + device_create_file(&client->dev, &sensor_dev_attr_in3_input.dev_attr); + device_create_file(&client->dev, &sensor_dev_attr_in3_min.dev_attr); + device_create_file(&client->dev, &sensor_dev_attr_in3_max.dev_attr); + device_create_file(&client->dev, &sensor_dev_attr_in3_alarm.dev_attr); + + /* Pin 110 is either in4 (+12V) or VID4 */ + config = i2c_smbus_read_byte_data(client, SMSC47M192_REG_CONFIG); + if (!(config & 0x20)) { + device_create_file(&client->dev, + &sensor_dev_attr_in4_input.dev_attr); + device_create_file(&client->dev, + &sensor_dev_attr_in4_min.dev_attr); + device_create_file(&client->dev, + &sensor_dev_attr_in4_max.dev_attr); + device_create_file(&client->dev, + &sensor_dev_attr_in4_alarm.dev_attr); + } + device_create_file(&client->dev, &sensor_dev_attr_in5_input.dev_attr); + device_create_file(&client->dev, &sensor_dev_attr_in5_min.dev_attr); + device_create_file(&client->dev, &sensor_dev_attr_in5_max.dev_attr); + device_create_file(&client->dev, &sensor_dev_attr_in5_alarm.dev_attr); + device_create_file(&client->dev, &sensor_dev_attr_in6_input.dev_attr); + device_create_file(&client->dev, &sensor_dev_attr_in6_min.dev_attr); + device_create_file(&client->dev, &sensor_dev_attr_in6_max.dev_attr); + device_create_file(&client->dev, &sensor_dev_attr_in6_alarm.dev_attr); + device_create_file(&client->dev, &sensor_dev_attr_in7_input.dev_attr); + device_create_file(&client->dev, &sensor_dev_attr_in7_min.dev_attr); + device_create_file(&client->dev, &sensor_dev_attr_in7_max.dev_attr); + device_create_file(&client->dev, &sensor_dev_attr_in7_alarm.dev_attr); + device_create_file(&client->dev, &sensor_dev_attr_temp1_input.dev_attr); + device_create_file(&client->dev, &sensor_dev_attr_temp1_max.dev_attr); + device_create_file(&client->dev, &sensor_dev_attr_temp1_min.dev_attr); + device_create_file(&client->dev, + &sensor_dev_attr_temp1_offset.dev_attr); + device_create_file(&client->dev, &sensor_dev_attr_temp1_alarm.dev_attr); + device_create_file(&client->dev, &sensor_dev_attr_temp2_input.dev_attr); + device_create_file(&client->dev, &sensor_dev_attr_temp2_max.dev_attr); + device_create_file(&client->dev, &sensor_dev_attr_temp2_min.dev_attr); + device_create_file(&client->dev, + &sensor_dev_attr_temp2_offset.dev_attr); + device_create_file(&client->dev, &sensor_dev_attr_temp2_alarm.dev_attr); + device_create_file(&client->dev, + &sensor_dev_attr_temp2_input_fault.dev_attr); + device_create_file(&client->dev, &sensor_dev_attr_temp3_input.dev_attr); + device_create_file(&client->dev, &sensor_dev_attr_temp3_max.dev_attr); + device_create_file(&client->dev, &sensor_dev_attr_temp3_min.dev_attr); + device_create_file(&client->dev, + &sensor_dev_attr_temp3_offset.dev_attr); + device_create_file(&client->dev, &sensor_dev_attr_temp3_alarm.dev_attr); + device_create_file(&client->dev, + &sensor_dev_attr_temp3_input_fault.dev_attr); + device_create_file(&client->dev, &dev_attr_cpu0_vid); + device_create_file(&client->dev, &dev_attr_vrm); + + return 0; + +exit_detach: + i2c_detach_client(client); +exit_free: + kfree(data); +exit: + return err; +} + +static int smsc47m192_detach_client(struct i2c_client *client) +{ + struct smsc47m192_data *data = i2c_get_clientdata(client); + int err; + + hwmon_device_unregister(data->class_dev); + + if ((err = i2c_detach_client(client))) + return err; + + kfree(data); + + return 0; +} + +static struct smsc47m192_data *smsc47m192_update_device(struct device *dev) +{ + struct i2c_client *client = to_i2c_client(dev); + struct smsc47m192_data *data = i2c_get_clientdata(client); + int i, config; + + down(&data->update_lock); + + if (time_after(jiffies, data->last_updated + HZ + HZ / 2) + || !data->valid) { + u8 sfr = i2c_smbus_read_byte_data(client, SMSC47M192_REG_SFR); + + dev_dbg(&client->dev, "Starting smsc47m192 update\n"); + + for (i = 0; i <= 7; i++) { + data->in[i] = i2c_smbus_read_byte_data(client, + SMSC47M192_REG_IN(i)); + data->in_min[i] = i2c_smbus_read_byte_data(client, + SMSC47M192_REG_IN_MIN(i)); + data->in_max[i] = i2c_smbus_read_byte_data(client, + SMSC47M192_REG_IN_MAX(i)); + } + for (i = 0; i < 3; i++) { + data->temp[i] = i2c_smbus_read_byte_data(client, + SMSC47M192_REG_TEMP[i]); + data->temp_max[i] = i2c_smbus_read_byte_data(client, + SMSC47M192_REG_TEMP_MAX[i]); + data->temp_min[i] = i2c_smbus_read_byte_data(client, + SMSC47M192_REG_TEMP_MIN[i]); + } + for (i = 1; i < 3; i++) + data->temp_offset[i] = i2c_smbus_read_byte_data(client, + SMSC47M192_REG_TEMP_OFFSET(i)); + /* first offset is temp_offset[0] if SFR bit 4 is set, + temp_offset[1] otherwise */ + if (sfr & 0x10) { + data->temp_offset[0] = data->temp_offset[1]; + data->temp_offset[1] = 0; + } else + data->temp_offset[0] = 0; + + data->vid = i2c_smbus_read_byte_data(client, SMSC47M192_REG_VID) + & 0x0f; + config = i2c_smbus_read_byte_data(client, + SMSC47M192_REG_CONFIG); + if (config & 0x20) + data->vid |= (i2c_smbus_read_byte_data(client, + SMSC47M192_REG_VID4) & 0x01) << 4; + data->alarms = i2c_smbus_read_byte_data(client, + SMSC47M192_REG_ALARM1) | + (i2c_smbus_read_byte_data(client, + SMSC47M192_REG_ALARM2) << 8); + + data->last_updated = jiffies; + data->valid = 1; + } + + up(&data->update_lock); + + return data; +} + +static int __init smsc47m192_init(void) +{ + return i2c_add_driver(&smsc47m192_driver); +} + +static void __exit smsc47m192_exit(void) +{ + i2c_del_driver(&smsc47m192_driver); +} + +MODULE_AUTHOR("Hartmut Rick <linux at rick.claranet.de>"); +MODULE_DESCRIPTION("SMSC47M192 driver"); +MODULE_LICENSE("GPL"); + +module_init(smsc47m192_init); +module_exit(smsc47m192_exit); -- 1.4.0
