On Sun, 2006-06-18 at 12:11 +0200, Jean Delvare wrote: > Hi Lou, > > First of all, I would suggest that you switch to a better e-mail > client. The one you use doesn't handle character encodings properly, > and generate very crappy HTML code. > > > I am running CentOS 4 (uname -r 2.6.9-34.0.1.EL) with an ECS NFORCE3-939 MB > > and AMD Athlon64 3000+ processor > > > > I am having problems with the CPU temp and core voltage value using > > lm-sensors. > > > Had to adjust voltages computations for in5 and in6 from a post I found > > regarding a TYAN mb that had the same chip: > > > > compute in5 (@ * (1+4.14)) - (4.096*4.14) , (@ + (4.096*4.14)) / (1+4.14) > > > > compute in6 (@ * (1+2.14)) - (4.096*2.14) , (@ + (4.096*2.14)) / (1+2.14) > > These are very board-specific. What makes you think these lines are > correct for your board? Do the displayed values (and labels) match what > the BIOS displays? Many recent motherboards do not monitor negative > voltage lines anymore. > > > [root at web etc]# sensors > > it87-isa-0290 > > Adapter: ISA adapter > > CPU VCore: +1.07 V (min = +1.28 V, max = +1.42 V) ALARM > > +1.5V: +1.47 V (min = +1.42 V, max = +1.57 V) > > +3.3V: +3.31 V (min = +3.14 V, max = +3.47 V) > > +5V: +4.92 V (min = +4.76 V, max = +5.24 V) > > +12V: +11.71 V (min = +11.39 V, max = +12.61 V) > > -12V: -12.11 V (min = -12.60 V, max = -11.37 V) > > -5V: -4.80 V (min = -5.25 V, max = -4.75 V) > > Stdby: +5.03 V (min = +4.76 V, max = +5.24 V) > > VBat: +2.94 V > > CPU Fan: 3245 RPM (min = 3013 RPM, div = 8) > > Case Fan: 981 RPM (min = 664 RPM, div = 8) > > Temp1: +4?C (low = +15?C, high = +40?C) sensor = thermistor > > Temp2: +30?C (low = +15?C, high = +45?C) sensor = thermistor > > > > Everything looks good except the CPU core voltage and CPU temp. > > > > The bios reads 1.37V for coreV but lm_sensors reads 1.07 consistently. > > This can be explained easily. Your Athlon64 3000+ must have the > so-called "Cool'n'Quiet" feature, which lets it adjust voltage and > frequency depending on load. I have a similar processor (Athlon64 > 3200+, socket 939) those voltage ranges from 1.1V (idle) to 1.4V (full > load.) This seems to be roughly the same for you. > > You may try commenting out the following line in your configuration file > (in the it87-* section, of course): > # ignore vid > If the VID pins are properly wired on your system, this should report > the nominal voltage for your CPU and you should see it change depending > on the load. > > So it's really only a matter of setting the proper limits for that kind > of CPU. Try the following: > > set in0_min 1.1 * 0.95 > set in0_max 1.4 * 1.05 > > > The bios for temps: MB = 31 and CPU = 52. Both are pretty consistent in the > > bios. > > > > The CPU temperature in lm_sensors fluctuates between -5 and 50. I have > > tried using the diode for both temp1 and temp2 and ignoring different > > combinations with no success. If the temperature was consistent I would > > feel better like a correction factor was needed but it is all over the > > place. I have the same problem with my ECS RX-480A motherboard that uses the IT8712 super I/O chip. The temperature sensor 2 fluctuates. I'm guessing that sensors_detect will only detect 1 super I/O chip, and only one sensor chip in the computer. I too would like to know how to get my email subject is "IT8712F-A and ECS-RX480A mainboard has erradic CPU temp." How do we get these ECS boards to behave with the CPU temp? temp3 didn't seem correctly because it's temperature didn't change to the work load on the CPU. That will probably be the same for yours. > > What about temp3? > > Or there could be an additional temperature sensor on the board. Can we > see the full output of sensors-detect? > > > Also the chip designation in sensors.conf is > > > > chip "it87-*" "it8712-*" > > > > If I have just "it8712-*" it does not detect the configuration in the > > sensors.conf and uses all defaults. > > In kernel 2.6.9 your chip is identified by the driver as "it87" (see > the first line of "sensors"), but in later kernels it is better > identified as "it8712". We put both in the configuration file so that > the same file works with all kernels. >
