I have searched in vain for a solution to my problem I was going to submit a support ticket but your website said to submit here instead. so here it goes. I've followed all instructions I could find. It seems as if all modules get detected and load fine. Yet running 'sensors returns 'No sensors found'. Any thoughts????? Kernel 2.6.14.5 (with gentoo patches)(SMP Opteron 64 bit) lm_sensors 2.9.2 Motherboard Tyan Tiger K8W S2875 Bios 3.02 Here's all the relavant output I can think of. btw this is will all i2c debugging kernel options on) lspci Code: 00:00.0 Host bridge: Advanced Micro Devices [AMD] AMD-8151 System Controller (rev 13) 00:01.0 PCI bridge: Advanced Micro Devices [AMD] AMD-8151 AGP Bridge (rev 13) 00:06.0 PCI bridge: Advanced Micro Devices [AMD] AMD-8111 PCI (rev 07) 00:07.0 ISA bridge: Advanced Micro Devices [AMD] AMD-8111 LPC (rev 05) 00:07.1 IDE interface: Advanced Micro Devices [AMD] AMD-8111 IDE (rev 03) 00:07.2 SMBus: Advanced Micro Devices [AMD] AMD-8111 SMBus 2.0 (rev 02) 00:07.3 Bridge: Advanced Micro Devices [AMD] AMD-8111 ACPI (rev 05) 00:07.5 Multimedia audio controller: Advanced Micro Devices [AMD] AMD-8111 AC97 Audio (rev 03) 00:18.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration 00:18.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address Map 00:18.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Controller 00:18.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscellaneous Control 01:00.0 VGA compatible controller: nVidia Corporation NV35 [GeForce FX 5900XT] (rev a1) 02:00.0 USB Controller: Advanced Micro Devices [AMD] AMD-8111 USB (rev 0b) 02:00.1 USB Controller: Advanced Micro Devices [AMD] AMD-8111 USB (rev 0b) 02:03.0 Ethernet controller: Intel Corporation 82541EI Gigabit Ethernet Controller (Copper) 02:05.0 Mass storage controller: Silicon Image, Inc. SiI 3114 [SATALink/SATARaid] Serial ATA Controller (rev 02) 02:0a.0 FireWire (IEEE 1394): VIA Technologies, Inc. IEEE 1394 Host Controller (rev 80) 02:0b.0 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 61) 02:0b.1 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 61) 02:0b.2 USB Controller: VIA Technologies, Inc. USB 2.0 (rev 62) lsmod Code: Module Size Used by nfs 211304 1 lockd 70096 2 nfs sunrpc 162632 3 nfs,lockd w83627hf 30480 0 hwmon_vid 3008 1 w83627hf hwmon 3784 1 w83627hf eeprom 8720 0 i2c_isa 7040 1 w83627hf snd_seq 62080 0 snd_seq_device 10192 1 snd_seq pwc 52492 0 videodev 12416 1 pwc snd_intel8x0 37160 3 snd_ac97_codec 108568 1 snd_intel8x0 snd_ac97_bus 3008 1 snd_ac97_codec snd_pcm 101000 3 snd_intel8x0,snd_ac97_codec snd_timer 27208 3 snd_seq,snd_pcm snd 63072 10 snd_seq,snd_seq_device,snd_intel8x0,snd_ac97_codec,snd_pcm,snd_timer soundcore 12128 1 snd snd_page_alloc 12240 2 snd_intel8x0,snd_pcm i2c_amd756 8900 0 i2c_amd8111 7040 0 nvidia 4857712 12 sbp2 25860 0 ohci1394 35020 0 ieee1394 108664 2 sbp2,ohci1394 usb_storage 70400 0 usbhid 40032 0 Relavent dmesg Code: ACPI: PCI Interrupt 0000:01:00.0[A] -> GSI 16 (level, low) -> IRQ 19 NVRM: loading NVIDIA Linux x86_64 NVIDIA Kernel Module 1.0-8178 Wed Dec 14 16:58:07 PST 2005 i2c_adapter i2c-0: adapter [SMBus2 AMD8111 adapter at c480] registered amd756_smbus 0000:00:07.3: SMBREV = 0x5 amd756_smbus 0000:00:07.3: AMD756_smba = 0x10E0 i2c_adapter i2c-1: adapter [SMBus AMD8111 adapter at 10e0] registered ACPI: PCI Interrupt 0000:00:07.5[B] -> GSI 17 (level, low) -> IRQ 18 intel8x0_measure_ac97_clock: measured 50753 usecs intel8x0: clocking to 48000 Linux video capture interface: v1.00 pwc Philips webcam module version 9.0.2-unofficial loaded. pwc Supports Philips PCA645/646, PCVC675/680/690, PCVC720[40]/730/740/750 & PCVC830/840. pwc Also supports the Askey VC010, various Logitech Quickcams, Samsung MPC-C10 and MPC-C30, pwc the Creative WebCam 5 & Pro Ex, SOTEC Afina Eye and Visionite VCS-UC300 and VCS-UM100. pwc Logitech QuickCam 4000 Pro USB webcam detected. pwc Registered as /dev/video0. usbcore: registered new driver Philips webcam e1000: eth0: e1000_watchdog_task: NIC Link is Up 100 Mbps Half Duplex i2c_adapter i2c-9191: ISA main adapter registered i2c-core: driver [eeprom] registered i2c_adapter i2c-0: found normal entry for adapter 0, addr 0x50 i2c_adapter i2c-0: found normal entry for adapter 0, addr 0x51 i2c_adapter i2c-0: found normal entry for adapter 0, addr 0x52 i2c_adapter i2c-0: found normal entry for adapter 0, addr 0x53 i2c_adapter i2c-0: found normal entry for adapter 0, addr 0x54 i2c_adapter i2c-0: found normal entry for adapter 0, addr 0x55 i2c_adapter i2c-0: found normal entry for adapter 0, addr 0x56 i2c_adapter i2c-0: found normal entry for adapter 0, addr 0x57 i2c_adapter i2c-1: found normal entry for adapter 1, addr 0x50 i2c_adapter i2c-1: Transaction (pre): GS=0004, GE=0000, ADD=00a0, DAT=0002 i2c_adapter i2c-1: SMBus Protocol error (no response)! i2c_adapter i2c-1: Transaction (post): GS=0000, GE=0000, ADD=00a0, DAT=0002 i2c_adapter i2c-1: found normal entry for adapter 1, addr 0x51 i2c_adapter i2c-1: Transaction (pre): GS=0000, GE=0000, ADD=00a2, DAT=0002 i2c_adapter i2c-1: SMBus protocol success! i2c_adapter i2c-1: Transaction (post): GS=0000, GE=0000, ADD=00a2, DAT=0002 i2c_adapter i2c-1: Transaction (pre): GS=0000, GE=0000, ADD=00a2, DAT=0002 i2c_adapter i2c-1: SMBus protocol success! i2c_adapter i2c-1: Transaction (post): GS=0000, GE=0000, ADD=00a2, DAT=0002 i2c_adapter i2c-1: client [eeprom] registered with bus id 1-0051 i2c_adapter i2c-1: found normal entry for adapter 1, addr 0x52 i2c_adapter i2c-1: Transaction (pre): GS=0000, GE=0000, ADD=00a4, DAT=0002 i2c_adapter i2c-1: SMBus Protocol error (no response)! i2c_adapter i2c-1: Transaction (post): GS=0000, GE=0000, ADD=00a4, DAT=0002 i2c_adapter i2c-1: found normal entry for adapter 1, addr 0x53 i2c_adapter i2c-1: Transaction (pre): GS=0000, GE=0000, ADD=00a6, DAT=0002 i2c_adapter i2c-1: SMBus Protocol error (no response)! i2c_adapter i2c-1: Transaction (post): GS=0000, GE=0000, ADD=00a6, DAT=0002 i2c_adapter i2c-1: found normal entry for adapter 1, addr 0x54 i2c_adapter i2c-1: Transaction (pre): GS=0000, GE=0000, ADD=00a8, DAT=0002 i2c_adapter i2c-1: SMBus Protocol error (no response)! i2c_adapter i2c-1: Transaction (post): GS=0000, GE=0000, ADD=00a8, DAT=0002 i2c_adapter i2c-1: found normal entry for adapter 1, addr 0x55 i2c_adapter i2c-1: Transaction (pre): GS=0000, GE=0000, ADD=00aa, DAT=0002 i2c_adapter i2c-1: SMBus Protocol error (no response)! i2c_adapter i2c-1: Transaction (post): GS=0000, GE=0000, ADD=00aa, DAT=0002 i2c_adapter i2c-1: found normal entry for adapter 1, addr 0x56 i2c_adapter i2c-1: Transaction (pre): GS=0000, GE=0000, ADD=00ac, DAT=0002 i2c_adapter i2c-1: SMBus Protocol error (no response)! i2c_adapter i2c-1: Transaction (post): GS=0000, GE=0000, ADD=00ac, DAT=0002 i2c_adapter i2c-1: found normal entry for adapter 1, addr 0x57 i2c_adapter i2c-1: Transaction (pre): GS=0000, GE=0000, ADD=00ae, DAT=0002 i2c_adapter i2c-1: SMBus Protocol error (no response)! i2c_adapter i2c-1: Transaction (post): GS=0000, GE=0000, ADD=00ae, DAT=0002 i2c_adapter i2c-9191: Driver w83627hf registered Relevant /var/log/messages Code: Jan 9 17:27:23 Gentoo64 ACPI: PCI Interrupt 0000:01:00.0[A] -> GSI 16 (level, low) -> IRQ 19 Jan 9 17:27:23 Gentoo64 NVRM: loading NVIDIA Linux x86_64 NVIDIA Kernel Module 1.0-8178 Wed Dec 14 16:58:07 PST 2005 Jan 9 17:27:23 Gentoo64 i2c_adapter i2c-0: adapter [SMBus2 AMD8111 adapter at c480] registered Jan 9 17:27:23 Gentoo64 amd756_smbus 0000:00:07.3: SMBREV = 0x5 Jan 9 17:27:23 Gentoo64 amd756_smbus 0000:00:07.3: AMD756_smba = 0x10E0 Jan 9 17:27:23 Gentoo64 i2c_adapter i2c-1: adapter [SMBus AMD8111 adapter at 10e0] registered Jan 9 17:27:23 Gentoo64 ACPI: PCI Interrupt 0000:00:07.5[B] -> GSI 17 (level, low) -> IRQ 18 Jan 9 17:27:23 Gentoo64 intel8x0_measure_ac97_clock: measured 50753 usecs Jan 9 17:27:23 Gentoo64 intel8x0: clocking to 48000 Jan 9 17:27:23 Gentoo64 Linux video capture interface: v1.00 Jan 9 17:27:23 Gentoo64 pwc Philips webcam module version 9.0.2-unofficial loaded. Jan 9 17:27:23 Gentoo64 pwc Supports Philips PCA645/646, PCVC675/680/690, PCVC720[40]/730/740/750 & PCVC830/840. Jan 9 17:27:23 Gentoo64 pwc Also supports the Askey VC010, various Logitech Quickcams, Samsung MPC-C10 and MPC-C30, Jan 9 17:27:23 Gentoo64 pwc the Creative WebCam 5 & Pro Ex, SOTEC Afina Eye and Visionite VCS-UC300 and VCS-UM100. Jan 9 17:27:23 Gentoo64 pwc Logitech QuickCam 4000 Pro USB webcam detected. Jan 9 17:27:23 Gentoo64 pwc Registered as /dev/video0. Jan 9 17:27:23 Gentoo64 usbcore: registered new driver Philips webcam Jan 9 17:27:23 Gentoo64 rc-scripts: Configuration not set for eth0 - assuming dhcp Jan 9 17:27:23 Gentoo64 e1000: eth0: e1000_watchdog_task: NIC Link is Up 100 Mbps Half Duplex Jan 9 17:27:29 Gentoo64 i2c_adapter i2c-9191: ISA main adapter registered Jan 9 17:27:29 Gentoo64 i2c-core: driver [eeprom] registered Jan 9 17:27:29 Gentoo64 i2c_adapter i2c-0: found normal entry for adapter 0, addr 0x50 Jan 9 17:27:29 Gentoo64 i2c_adapter i2c-0: found normal entry for adapter 0, addr 0x51 Jan 9 17:27:29 Gentoo64 i2c_adapter i2c-0: found normal entry for adapter 0, addr 0x52 Jan 9 17:27:29 Gentoo64 i2c_adapter i2c-0: found normal entry for adapter 0, addr 0x53 Jan 9 17:27:29 Gentoo64 i2c_adapter i2c-0: found normal entry for adapter 0, addr 0x54 Jan 9 17:27:29 Gentoo64 i2c_adapter i2c-0: found normal entry for adapter 0, addr 0x55 Jan 9 17:27:29 Gentoo64 i2c_adapter i2c-0: found normal entry for adapter 0, addr 0x56 Jan 9 17:27:29 Gentoo64 i2c_adapter i2c-0: found normal entry for adapter 0, addr 0x57 Jan 9 17:27:29 Gentoo64 i2c_adapter i2c-1: found normal entry for adapter 1, addr 0x50 Jan 9 17:27:29 Gentoo64 i2c_adapter i2c-1: Transaction (pre): GS=0004, GE=0000, ADD=00a0, DAT=0002 Jan 9 17:27:29 Gentoo64 i2c_adapter i2c-1: SMBus Protocol error (no response)! Jan 9 17:27:29 Gentoo64 i2c_adapter i2c-1: Transaction (post): GS=0000, GE=0000, ADD=00a0, DAT=0002 Jan 9 17:27:29 Gentoo64 i2c_adapter i2c-1: found normal entry for adapter 1, addr 0x51 Jan 9 17:27:29 Gentoo64 i2c_adapter i2c-1: Transaction (pre): GS=0000, GE=0000, ADD=00a2, DAT=0002 Jan 9 17:27:29 Gentoo64 i2c_adapter i2c-1: SMBus protocol success! Jan 9 17:27:29 Gentoo64 i2c_adapter i2c-1: Transaction (post): GS=0000, GE=0000, ADD=00a2, DAT=0002 Jan 9 17:27:29 Gentoo64 i2c_adapter i2c-1: Transaction (pre): GS=0000, GE=0000, ADD=00a2, DAT=0002 Jan 9 17:27:29 Gentoo64 i2c_adapter i2c-1: SMBus protocol success! Jan 9 17:27:29 Gentoo64 i2c_adapter i2c-1: Transaction (post): GS=0000, GE=0000, ADD=00a2, DAT=0002 Jan 9 17:27:29 Gentoo64 i2c_adapter i2c-1: client [eeprom] registered with bus id 1-0051 Jan 9 17:27:29 Gentoo64 i2c_adapter i2c-1: found normal entry for adapter 1, addr 0x52 Jan 9 17:27:29 Gentoo64 i2c_adapter i2c-1: Transaction (pre): GS=0000, GE=0000, ADD=00a4, DAT=0002 Jan 9 17:27:29 Gentoo64 i2c_adapter i2c-1: SMBus Protocol error (no response)! Jan 9 17:27:29 Gentoo64 i2c_adapter i2c-1: Transaction (post): GS=0000, GE=0000, ADD=00a4, DAT=0002 Jan 9 17:27:29 Gentoo64 i2c_adapter i2c-1: found normal entry for adapter 1, addr 0x53 Jan 9 17:27:29 Gentoo64 i2c_adapter i2c-1: Transaction (pre): GS=0000, GE=0000, ADD=00a6, DAT=0002 Jan 9 17:27:29 Gentoo64 i2c_adapter i2c-1: SMBus Protocol error (no response)! Jan 9 17:27:29 Gentoo64 i2c_adapter i2c-1: Transaction (post): GS=0000, GE=0000, ADD=00a6, DAT=0002 Jan 9 17:27:29 Gentoo64 i2c_adapter i2c-1: found normal entry for adapter 1, addr 0x54 Jan 9 17:27:29 Gentoo64 i2c_adapter i2c-1: Transaction (pre): GS=0000, GE=0000, ADD=00a8, DAT=0002 Jan 9 17:27:29 Gentoo64 i2c_adapter i2c-1: SMBus Protocol error (no response)! Jan 9 17:27:29 Gentoo64 i2c_adapter i2c-1: Transaction (post): GS=0000, GE=0000, ADD=00a8, DAT=0002 Jan 9 17:27:29 Gentoo64 i2c_adapter i2c-1: found normal entry for adapter 1, addr 0x55 Jan 9 17:27:29 Gentoo64 i2c_adapter i2c-1: Transaction (pre): GS=0000, GE=0000, ADD=00aa, DAT=0002 Jan 9 17:27:29 Gentoo64 i2c_adapter i2c-1: SMBus Protocol error (no response)! Jan 9 17:27:29 Gentoo64 i2c_adapter i2c-1: Transaction (post): GS=0000, GE=0000, ADD=00aa, DAT=0002 Jan 9 17:27:29 Gentoo64 i2c_adapter i2c-1: found normal entry for adapter 1, addr 0x56 Jan 9 17:27:29 Gentoo64 i2c_adapter i2c-1: Transaction (pre): GS=0000, GE=0000, ADD=00ac, DAT=0002 Jan 9 17:27:29 Gentoo64 i2c_adapter i2c-1: SMBus Protocol error (no response)! Jan 9 17:27:29 Gentoo64 i2c_adapter i2c-1: Transaction (post): GS=0000, GE=0000, ADD=00ac, DAT=0002 Jan 9 17:27:29 Gentoo64 i2c_adapter i2c-1: found normal entry for adapter 1, addr 0x57 Jan 9 17:27:29 Gentoo64 i2c_adapter i2c-1: Transaction (pre): GS=0000, GE=0000, ADD=00ae, DAT=0002 Jan 9 17:27:29 Gentoo64 i2c_adapter i2c-1: SMBus Protocol error (no response)! Jan 9 17:27:29 Gentoo64 i2c_adapter i2c-1: Transaction (post): GS=0000, GE=0000, ADD=00ae, DAT=0002 Jan 9 17:27:29 Gentoo64 i2c_adapter i2c-9191: Driver w83627hf registered I'm lost I don't know what else to try. Any suggestion would be more than appreciated. PS MY bios allow both ACPI version 1 or 2 I've tried both and got the same results. Thanks in advance!!!!!!!!!
