> > So, this problem seems to be solved now; what still remain is that I'm
> > a little suspicious about voltage readings looking too much
> > idealistic, like Vcore 1.500 Volts...
>
> Isn't it rather VID? VID is the nominal voltage value for the CPU, not
> the measured one. in0 or in1 would be. VID is there so that you can set
> the relevant low and high limits to something that makes sense for your
> specific CPU.
>
I think Vcore is measured from pin 'in1', but it produces 'too' good stable
reading of 1.500 anyway -from day to day. It's not exactly the same what I
can see in bios, but the reading is quite stable there too. The slight
difference (1.494 in bios) _could_ be caused by slightly different current
consumption, maybe? I have tested this both in console, and in a terminal
window under X, both result always in 1.500. Strange? I've tried this so far
in only one computer, maybe the next one will give different figures.
Or am I thinking something in a wrong way again? Below is the output of
'sensors' and piece of sensors.conf.
lm_sensors is version 2.8.7-2, from current FC3 rpm.
Limits of Vcore are based to VID, which equals to 0. Is it a variable that
needs to be se manually in the file, or should it be automatically readable
from somewhere.
adm1027-i2c-0-2e
Adapter: SMBus I801 adapter at c400
ERROR: Can't get alarm mask data!
V1.5: +1.471 V (min = +1.42 V, max = +1.58 V)
VCore: +1.500 V (min = +0.00 V, max = +0.00 V) ALARM
V3.3: +3.403 V (min = +3.13 V, max = +3.47 V)
V5: +5.156 V (min = +4.74 V, max = +5.26 V)
V12: +12.313 V (min = +11.38 V, max = +12.62 V)
CPU_Fan: 3170 RPM (min = 4000 RPM) ALARM
Front/Power_Fan:
2881 RPM (min = 0 RPM)
Rear/Exit_Fan:
2884 RPM (min = 0 RPM)
CPU: +27.00?C (low = +10?C, high = +50?C)
Board: +25.00?C (low = +10?C, high = +35?C)
Remote: +27.00?C (low = +10?C, high = +35?C)
ERROR: Can't get PWM1 data!
ERROR: Can't get PWM2 data!
ERROR: Can't get PWM3 data!
# Sample configuration for the Intel S845WD1-E
# courtesy of Marcus Schopen
#
chip "lm85c-*" "adm1027-*" "adt7463-*" "lm85-*" "lm85b-*"
set temp1_max 50
# Voltage inputs
label in0 "V1.5" # AGP on Intel S845WD1-E
label in1 "VCore"
label in2 "V3.3"
label in3 "V5"
label in4 "V12"
# Temperature inputs
label temp1 "CPU"
label temp2 "Board"
label temp3 "Remote"
# Fan inputs
label fan1 "CPU_Fan"
label fan2 "Fan2"
label fan3 "Front/Power_Fan"
label fan4 "Rear/Exit_Fan"
# PWM Outputs
label pwm1 "CPU_PWM"
label pwm2 "Fan2_PWM"
label pwm3 "Fan3_PWM"
# Voltage scaling is done on-chip. No 'compute' directive
# should be necessary. If in0 has external scaling set
# it here.
# compute in0 @ * 2.5, @ / 2.5
# Adjust fans speeds for actual pulses per rev
# compute fan1 @ * 2, @ / 2 # 1 pulse per rev
# set fan1_ppr 1 # ADM1027 or ADT7463
# compute fan2 @ / 2, @ * 2 # 4 pulse per rev
# set fan2_ppr 4 # ADM1027 or ADT7463
ignore fan2
# ignore fan3
# ignore fan4
# Set VRM version
set vrm 9.1 # Pentium 4
# Set voltage limits
set in0_min 1.5 * 0.95
set in0_max 1.5 * 1.05
set in1_min vid * 0.95
set in1_max vid * 1.05
set in2_min 3.3 * 0.95
set in2_max 3.3 * 1.05
set in3_min 5.0 * 0.95
set in3_max 5.0 * 1.05
set in4_min 12 * 0.95
set in4_max 12 * 1.05
# Set Fan limits
set fan1_min 4000
# Set Temp Limits
set temp1_min 10
set temp1_max 50
set temp2_min 10
set temp2_max 35
set temp3_min 10
set temp3_max 35
