copied to rgooch due to mtrr messages...
copied to lm78 due to i2c radeon messages..
copied to ndiswrapper folks as 2.6.3 is last version where ndiswrapper
runs before coredumping... 2.6.4-rc1 gives a fatal dump on wlan0
init with hard paging crash
2.3.6 config is attached
btw 2.6.3 runs. 2.6.4-rc1 runs 2.6.4.rc1 with ndiswrapper doesn't.
eMachines M5312
From dmidecode:
# dmidecode 1.8
ACPI 1.0 present.
OEM ID: ARIMA
RSD table at 0x1BEFAE80.
SMBIOS 2.3 present.
DMI 2.3 present.
18 structures occupying 694 bytes.
DMI table at 0x000DF010.
Handle 0x0000
DMI type 0, 20 bytes.
BIOS Information Block
Vendor: Phoenix
Version: 0010
Release: 09/07/2003
BIOS base: 0xE5EB0
ROM size: 512K
Capabilities:
Flags: 0x000000000003DF90
Handle 0x0001
DMI type 1, 25 bytes.
System Information Block
Vendor: eMachines. Inc.
Product: M5300 Series.
Version: 0010
Serial Number: N703X 500 02506
Handle 0x0002
DMI type 2, 8 bytes.
Board Information Block
Vendor: Arima
Product: W720K7
Version: KBC Revision: 1913
Serial Number: None
Handle 0x0003
DMI type 3, 17 bytes.
Chassis Information Block
Vendor: Arima
Chassis Type: Notebook
Version: N/A
Serial Number: None
Asset Tag:
Handle 0x0004
DMI type 4, 32 bytes.
Processor
Socket Designation: U23
Processor Type: Central Processor
Processor Family: K5
Processor Manufacturer: AuthenticAMD
Processor Version: Mobile AMD Athlon(tm) XP processor
2400+
Handle 0x0005
DMI type 7, 19 bytes.
Cache
Socket: L1 Cache
L1 Internal Cache: write-back
L1 Cache Size: 128K
L1 Cache Maximum: 128K
L1 Cache Type: Synchronous
Handle 0x0006
DMI type 7, 19 bytes.
Cache
Socket: L2 Cache
L2 socketed Internal Cache: write-back
L2 Cache Size: 512K
L2 Cache Maximum: 512K
L2 Cache Type: Synchronous
Handle 0x0007
DMI type 16, 15 bytes.
Physical Memory Array
Location: System board or motherboard
Use: Flash memory
Error Correction Type: None
Maximum Capacity: 512 kB
Error Information Handle: Not Provided
Number of Devices: 1
Handle 0x0008
DMI type 16, 15 bytes.
Physical Memory Array
Location: System board or motherboard
Use: System memory
Error Correction Type: None
Maximum Capacity: 1048576 kB
Error Information Handle: Not Provided
Number of Devices: 2
Handle 0x0009
DMI type 17, 23 bytes.
Memory Device
Array Handle: 0x0008
Error Information Handle: Not Provided
Total Width: 64 bits
Data Width: 64 bits
Size: 256 Mbyte
Form Factor: DIMM
Set: 0x01
Locator: U5
Bank Locator: Bank 0
Type: DRAM
Type Detail: Synchronous
Speed: 266 MHz (3.8 ns)
Handle 0x000A
DMI type 17, 23 bytes.
Memory Device
Array Handle: 0x0008
Error Information Handle: Not Provided
Total Width: 64 bits
Data Width: 64 bits
Size: 256 Mbyte
Form Factor: DIMM
Set: 0x01
Locator: U6
Bank Locator: Bank 1
Type: DRAM
Type Detail: Synchronous
Speed: 266 MHz (3.8 ns)
Handle 0x000B
DMI type 17, 23 bytes.
Memory Device
Array Handle: 0x0007
Error Information Handle: Not Provided
Total Width: 16 bits
Data Width: 16 bits
Size: 512 Kbyte
Form Factor: Chip
Locator: System Board
Bank Locator: Null
Type: FLASH
Type Detail:
Speed: 8 MHz (125.0 ns)
Handle 0x000C
DMI type 19, 15 bytes.
Memory Array Mapped Address
Handle 0x000D
DMI type 19, 15 bytes.
Memory Array Mapped Address
Handle 0x000E
DMI type 20, 19 bytes.
Memory Device Mapped Address
Handle 0x000F
DMI type 20, 19 bytes.
Memory Device Mapped Address
Handle 0x0010
DMI type 32, 20 bytes.
System Boot Information
Handle 0x0011
DMI type 127, 4 bytes.
End-of-Table
BIOS32 Service Directory present.
Calling Interface Address: 0x000FD770
PNP 1.0 present.
Event Notification: Not Supported
Real Mode Code Address: F000:A2C0
Real Mode Data Address: 0040:0000
Protected Mode Code Address: 0x000FA2DE
Protected Mode Data Address: 0x00000400
PCI Interrupt Routing 1.0 present.
Table Size: 192 bytes
Router ID: 00:07.0
Exclusive IRQs: None
Compatible Router: 10b9:1533
CPUINFO:
cpuinfo.txt
processor : 0
vendor_id : AuthenticAMD
cpu family : 6
model : 10
model name : Mobile AMD Athlon(tm) XP 2400+
stepping : 0
cpu MHz : 1788.968
cache size : 512 KB
fdiv_bug : no
hlt_bug : no
f00f_bug : no
coma_bug : no
fpu : yes
fpu_exception : yes
cpuid level : 1
wp : yes
flags : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge
mca cmov pat pse36 mmx fxsr sse syscall mp mmxext 3dnowex
t 3dnow
s : 3538.94
DMESG:
bogomipLinux version 2.6.3 (root at enlaptop.ameritech.net) (gcc version
3.3.1 (Mandrake Linux 9.2 3.3.1-2mdk)) #2 Tue Feb 24 19:57:46 UTC
2004
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009f800 (usable)
BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000d0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000001bef0000 (usable)
BIOS-e820: 000000001bef0000 - 000000001beff000 (ACPI data)
BIOS-e820: 000000001beff000 - 000000001bf00000 (ACPI NVS)
BIOS-e820: 000000001bf00000 - 000000001c000000 (usable)
BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved)
448MB LOWMEM available.
On node 0 totalpages: 114688
DMA zone: 4096 pages, LIFO batch:1
Normal zone: 110592 pages, LIFO batch:16
HighMem zone: 0 pages, LIFO batch:1
DMI 2.3 present.
ACPI: RSDP (v000 ARIMA ) @ 0x000f7680
ACPI: RSDT (v001 PTLTD RSDT 0x06040000 LTP 0x00000000) @ 0x1befae80
ACPI: FADT (v001 ARIMA W720-K7 0x06040000 PTL_ 0x000f4240) @ 0x1befee53
ACPI: SSDT (v001 PTLTD POWERNOW 0x06040000 LTP 0x00000001) @ 0x1befeec7
ACPI: DSDT (v001 ARIMA W720-K7 0x06040000 MSFT 0x0100000d) @ 0x00000000
Built 1 zonelists
Kernel command line: BOOT_IMAGE=263 ro root=305 devfs=mount hdc=ide-cd
resume=/dev/hda6 splash=silent
ide_setup: hdc=ide-cd
Local APIC disabled by BIOS -- reenabling.
Found and enabled local APIC!
Initializing CPU#0
PID hash table entries: 2048 (order 11: 16384 bytes)
Detected 1788.968 MHz processor.
Using tsc for high-res timesource
Console: colour dummy device 80x25
Memory: 449788k/458752k available (2247k kernel code, 8132k reserved,
902k data, 168k init, 0k highmem)
Checking if this processor honours the WP bit even in supervisor
mode... Ok.
Calibrating delay loop... 3538.94 BogoMIPS
Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
checking if image is initramfs...it isn't (no cpio magic); looks like
an initrd
Freeing initrd memory: 18k freed
CPU: After generic identify, caps: 0383fbff c1cbfbff 00000000 00000000
CPU: After vendor identify, caps: 0383fbff c1cbfbff 00000000 00000000
CPU: CLK_CTL MSR was 60071263. Reprogramming to 20071263
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 512K (64 bytes/line)
CPU: After all inits, caps: 0383fbff c1cbfbff 00000000 00000020
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU: AMD Mobile AMD Athlon(tm) XP 2400+ stepping 00
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
POSIX conformance testing by UNIFIX
enabled ExtINT on CPU#0
ESR value before enabling vector: 00000000
ESR value after enabling vector: 00000000
Using local APIC timer interrupts.
calibrating APIC timer ...
.... CPU clock speed is 1788.0673 MHz.
.... host bus clock speed is 264.0988 MHz.
NET: Registered protocol family 16
PCI: PCI BIOS revision 2.10 entry at 0xfd88e, last bus=1
PCI: Using configuration type 1
mtrr: v2.0 (20020519)
ACPI: Subsystem revision 20040116
spurious 8259A interrupt: IRQ7.
ACPI: IRQ9 SCI: Edge set to Level Trigger.
ACPI: Interpreter enabled
ACPI: Using PIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (00:00)
PCI: Probing PCI hardware (bus 00)
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Link [LNK0] (IRQs 3 4 5 6 7 10 11 12)
ACPI: PCI Interrupt Link [LNK1] (IRQs 3 4 5 6 7 10 *11 12)
ACPI: PCI Interrupt Link [LNK2] (IRQs 3 4 5 6 7 *10 11 12)
ACPI: PCI Interrupt Link [LNK3] (IRQs 3 4 5 6 7 10 *11 12)
ACPI: PCI Interrupt Link [LNK4] (IRQs 3 4 5 6 7 10 11 12)
ACPI: PCI Interrupt Link [LNK5] (IRQs 3 4 5 6 7 10 11 12)
ACPI: PCI Interrupt Link [LNK6] (IRQs 3 4 *5 6 7 10 11 12)
ACPI: PCI Interrupt Link [LNK7] (IRQs 3 4 5 6 7 10 *11 12)
ACPI: PCI Interrupt Link [LNK8] (IRQs 3 4 5 6 7 10 11 12)
ACPI: Embedded Controller [EC] (gpe 24)
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.AGP_._PRT]
ACPI: PCI Interrupt Link [LNK7] enabled at IRQ 11
ACPI: PCI Interrupt Link [LNK6] enabled at IRQ 5
ACPI: PCI Interrupt Link [LNK2] enabled at IRQ 10
ACPI: PCI Interrupt Link [LNK1] enabled at IRQ 11
ACPI: PCI Interrupt Link [LNK3] enabled at IRQ 11
ACPI: No IRQ known for interrupt pin A of device 0000:00:10.0
PCI: Using ACPI for IRQ routing
PCI: if you experience problems, try using option 'pci=noacpi' or even
'acpi=off'
radeonfb_pci_register BEGIN
radeonfb: probed SDR SGRAM 245760k videoram
radeonfb: mapped 16384k videoram
radeonfb: Invalid ROM signature 0 should be 0xaa55
radeonfb: Retreived PLL infos from BIOS
radeonfb: Reference=191.86 MHz (RefDiv=426) Memory=160.00 Mhz,
System=133.00 MHz
i2c_adapter i2c-0: registered as adapter #0
i2c_adapter i2c-1: registered as adapter #1
i2c_adapter i2c-2: registered as adapter #2
i2c_adapter i2c-3: registered as adapter #3
1 chips in connector info
- chip 1 has 1 connectors
* connector 0 of type 2 (CRT) : 2300
Starting monitor auto detection...
i2c_adapter i2c-0: master_xfer: with 2 msgs.
i2c_adapter i2c-0: master_xfer: with 2 msgs.
i2c_adapter i2c-0: master_xfer: with 2 msgs.
radeonfb: I2C (port 1) ... not found
i2c_adapter i2c-1: master_xfer: with 2 msgs.
i2c_adapter i2c-1: master_xfer: with 2 msgs.
i2c_adapter i2c-1: master_xfer: with 2 msgs.
radeonfb: I2C (port 2) ... not found
i2c_adapter i2c-2: master_xfer: with 2 msgs.
i2c_adapter i2c-2: master_xfer: with 2 msgs.
i2c_adapter i2c-2: master_xfer: with 2 msgs.
radeonfb: I2C (port 3) ... not found
i2c_adapter i2c-3: master_xfer: with 2 msgs.
i2c_adapter i2c-3: master_xfer: with 2 msgs.
i2c_adapter i2c-3: master_xfer: with 2 msgs.
radeonfb: I2C (port 4) ... not found
i2c_adapter i2c-1: master_xfer: with 2 msgs.
i2c_adapter i2c-1: master_xfer: with 2 msgs.
i2c_adapter i2c-1: master_xfer: with 2 msgs.
radeonfb: I2C (port 2) ... not found
i2c_adapter i2c-3: master_xfer: with 2 msgs.
i2c_adapter i2c-3: master_xfer: with 2 msgs.
i2c_adapter i2c-3: master_xfer: with 2 msgs.
radeonfb: I2C (port 4) ... not found
Non-DDC laptop panel detected
i2c_adapter i2c-2: master_xfer: with 2 msgs.
i2c_adapter i2c-2: master_xfer: with 2 msgs.
i2c_adapter i2c-2: master_xfer: with 2 msgs.
radeonfb: I2C (port 3) ... not found
i2c_adapter i2c-3: master_xfer: with 2 msgs.
i2c_adapter i2c-3: master_xfer: with 2 msgs.
i2c_adapter i2c-3: master_xfer: with 2 msgs.
radeonfb: I2C (port 4) ... not found
radeonfb: Monitor 1 type LCD found
radeonfb: Monitor 2 type no found
radeonfb: panel ID string: 1280x800 WXGA
radeonfb: detected LVDS panel size from BIOS: 1280x800
BIOS provided panel power delay: 400
radeondb: BIOS provided dividers will be used
ref_divider = 14
post_divider = 2
fbk_divider = 1d
Scanning BIOS table ...
320 x 350
320 x 400
320 x 400
320 x 480
400 x 600
512 x 384
640 x 350
640 x 400
640 x 475
640 x 480
720 x 480
720 x 576
800 x 600
848 x 480
1024 x 768
1280 x 800
Found panel in BIOS table:
hblank: 144
hOver_plus: 72
hSync_width: 32
vblank: 12
vOver_plus: 2
vSync_width: 1
clock: 6950
Setting up default mode based on panel info
radeonfb: Power Management enabled for Mobility chipsets
mtrr: base(0xe0000000) is not aligned on a size(0xf000000) boundary
radeonfb: ATI Radeon C6 SDR SGRAM 240 MB
radeonfb_pci_register END
vesafb: abort, cannot reserve video memory at 0xe0000000
vesafb: framebuffer at 0xe0000000, mapped to 0xdd835000, size 16384k
vesafb: mode is 800x600x16, linelength=1600, pages=67
vesafb: protected mode interface info at c000:511f
vesafb: scrolling: redraw
vesafb: directcolor: size=0:5:6:5, shift=0:11:5:0
fb1: VESA VGA frame buffer device
Machine check exception polling timer started.
powernow: PowerNOW! Technology present. Can scale: frequency and voltage.
powernow: Found PSB header at c00f0c70
powernow: Table version: 0x12
powernow: Flags: 0x0 (Mobile voltage regulator)
powernow: Settling Time: 100 microseconds.
powernow: Has 43 PST tables. (Only dumping ones relevant to this CPU).
powernow: No PST tables match this cpuid (0x7a0)
powernow: This is indicative of a broken BIOS.
powernow: See
http://www.codemonkey.org.uk/projects/cpufreq/powernow-k7.shtml
apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac)
apm: overridden by ACPI.
ikconfig 0.7 with /proc/config*
VFS: Disk quotas dquot_6.5.1
devfs: v1.22 (20021013) Richard Gooch (rgooch at atnf.csiro.au)
devfs: boot_options: 0x1
udf: registering filesystem
Initializing Cryptographic API
ATI Northbridge, reserving I/O ports 0x3b0 to 0x3bb.
Activating ISA DMA hang workarounds.
hStart = 1352, hEnd = 1384, hTotal = 1424
vStart = 802, vEnd = 803, vTotal = 812
h_total_disp = 0x9f00b1 hsync_strt_wid = 0x40542
v_total_disp = 0x31f032b vsync_strt_wid = 0x10321
pixclock = 14388
freq = 6950
lvds_gen_cntl: 003dffa1
Console: switching to colour frame buffer device 160x100
pty: 1024 Unix98 ptys configured
[drm] Initialized radeon 1.9.0 20020828 on minor 0
RAMDISK driver initialized: 16 RAM disks of 32000K size 1024 blocksize
b44.c:v0.92 (Nov 4, 2003)
eth0: Broadcom 4400 10/100BaseT Ethernet 00:03:25:0b:90:4f
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with
idebus=xx
Warning: ATI Radeon IGP Northbridge is not yet fully tested.
ALI15X3: IDE controller at PCI slot 0000:00:10.0
ACPI: No IRQ known for interrupt pin A of device 0000:00:10.0
ALI15X3: chipset revision 196
ALI15X3: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0x8080-0x8087, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0x8088-0x808f, BIOS settings: hdc:DMA, hdd:pio
hda: HITACHI_DK23FB-60, ATA DISK drive
Using anticipatory io scheduler
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
hdc: Slimtype COMBO LSC-24082K, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
hda: max request size: 128KiB
hda: 117210240 sectors (60011 MB) w/8192KiB Cache, CHS=65535/16/63,
UDMA(100)
/dev/ide/host0/bus0/target0/lun0: p1 p2 p3 < p5 p6 p7 >
hdc: ATAPI 24X DVD-ROM CD-R/RW CD-MRW drive, 2048kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
Console: switching to colour frame buffer device 160x100
mice: PS/2 mouse device common for all mice
serio: i8042 AUX port at 0x60,0x64 irq 12
Synaptics Touchpad, model: 1
Firmware: 5.9
Sensor: 35
new absolute packet format
Touchpad has extended capability bits
-> multifinger detection
-> palm detection
input: SynPS/2 Synaptics TouchPad on isa0060/serio1
serio: i8042 KBD port at 0x60,0x64 irq 1
input: AT Translated Set 2 keyboard on isa0060/serio0
I2O Core - (C) Copyright 1999 Red Hat Software
I2O: Event thread created as pid 10
i2o: Checking for PCI I2O controllers...
I2O configuration manager v 0.04.
(C) Copyright 1999 Red Hat Software
I2O Block Storage OSM v0.9
(c) Copyright 1999-2001 Red Hat Software.
i2o_block: Checking for Boot device...
i2o_block: Checking for I2O Block devices...
i2c /dev entries driver
i2c-core: driver dev_driver registered.
i2c_adapter i2c-0: Registered as minor 0
i2c_adapter i2c-1: Registered as minor 1
i2c_adapter i2c-2: Registered as minor 2
i2c_adapter i2c-3: Registered as minor 3
ali1535_smbus 0000:00:11.0: SMBREV = 0x0
ali1535_smbus 0000:00:11.0: ALI1535_smba = 0x8040
i2c_adapter i2c-4: Registered as minor 4
i2c_adapter i2c-4: registered as adapter #4
NET: Registered protocol family 2
IP: routing cache hash table of 4096 buckets, 32Kbytes
TCP: Hash tables configured (established 32768 bind 65536)
NET: Registered protocol family 1
Resume Machine: resuming from /dev/hda6
Resuming from device hda6
Resume Machine: This is normal swap space
PM: Reading pmdisk image.
PM: Resume from disk failed.
ACPI: (supports S0 S3 S4 S5)
RAMDISK: Compressed image found at block 0
VFS: Mounted root (ext2 filesystem).
Mounted devfs on /dev
EXT3-fs: INFO: recovery required on readonly filesystem.
EXT3-fs: write access will be enabled during recovery.
kjournald starting. Commit interval 5 seconds
EXT3-fs: recovery complete.
EXT3-fs: mounted filesystem with ordered data mode.
Mounted devfs on /dev
Freeing unused kernel memory: 168k freed
Real Time Clock Driver v1.12
drivers/usb/core/usb.c: registered new driver usbfs
drivers/usb/core/usb.c: registered new driver hub
ehci_hcd 0000:00:0d.2: EHCI Host Controller
ehci_hcd 0000:00:0d.2: irq 11, pci mem de84c800
ehci_hcd 0000:00:0d.2: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:0d.2: USB 2.0 enabled, EHCI 1.00, driver 2003-Dec-29
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 5 ports detected
EXT3 FS on hda5, internal journal
Adding 506008k swap on /dev/hda6. Priority:-1 extents:1
kjournald starting. Commit interval 5 seconds
EXT3 FS on hda7, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
NTFS driver 2.1.6 [Flags: R/O MODULE].
NTFS-fs warning (device hda1): parse_options(): Option iocharset is
deprecated. Please use option nls=<charsetname> in the futur
e.
NTFS volume version 3.0.
ohci1394: $Rev: 1097 $ Ben Collins <bcollins at debian.org>
ohci1394: fw-host0: OHCI-1394 1.0 (PCI): IRQ=[10]
MMIO=[d000c000-d000c7ff] Max Packet=[2048]
ieee1394: Host added: ID:BUS[0-00:1023] GUID[000325211900df9c]
From:
/var/log/kernel/info:
Feb 28 12:20:16 enlaptop kernel: Machine check exception polling timer
started.
Feb 28 12:20:16 enlaptop kernel: powernow: PowerNOW! Technology
present. Can scale: frequency and voltage.
Feb 28 12:20:16 enlaptop kernel: powernow: Found PSB header at c00f0c70
Feb 28 12:20:16 enlaptop kernel: powernow: Table version: 0x12
Feb 28 12:20:16 enlaptop kernel: powernow: Flags: 0x0 (Mobile voltage
regulator)
Feb 28 12:20:16 enlaptop kernel: powernow: Settling Time: 100
microseconds.
Feb 28 12:20:16 enlaptop kernel: powernow: Has 43 PST tables. (Only
dumping ones relevant to this CPU).
Feb 28 12:20:16 enlaptop kernel: powernow: No PST tables match this
cpuid (0x7a0)
Feb 28 12:20:16 enlaptop kernel: powernow: This is indicative of a
broken BIOS.
Feb 28 12:20:16 enlaptop kernel: powernow: See
http://www.codemonkey.org.uk/projects/cpufreq/powernow-k7.shtml
-------------- next part --------------
An embedded and charset-unspecified text was scrubbed...
Name: 2.6.3config
Url: http://lists.lm-sensors.org/pipermail/lm-sensors/attachments/20040228/d37dec4c/attachment.pl
