no you don't need i2c-algo-biths. You can use 'make -k' to keep going after an error. Try rmmoding the amd8111 module, then running sensors-detect again, then saying no when it asks to load it, but say yes to the 756 module. Also see if there is any info in dmesg if it fails to load. Marc Rieffel wrote: > > [Correction: This system has an ADM1026 chip, not a Sinbond chip.] > > I'm having trouble with i2c and lm_sensors on my dual Opteron Arima motherboard. This has an AMD 8111 chip and an ADM 1026jst chip. I'm running 64-bit SuSE. > > When I try to build i2c, I get an error, > > gcc -I/lib/modules/2.4.19MARi2c-NUMA/build/include -nostdinc -I /usr/lib64/gcc-lib/x86_64-suse-linux/3.2.2/include -Wall -O2 -DLM_SENSORS -D__KERNEL__ -DMODULE -fomit-frame-pointer -DEXPORT_SYMTAB -fno-strict-aliasing -fno-common -fomit-frame-pointer -mno-red-zone -mcmodel=kernel -fno-reorder-blocks -finline-limit=2000 -fno-strength-reduce -c kernel/i2c-algo-biths.c -o kernel/i2c-algo-biths.o > /tmp/ccP00QFi.s: Assembler messages: > /tmp/ccP00QFi.s:1424: Error: Incorrect register `%rdx' used with `l' suffix > make: *** [kernel/i2c-algo-biths.o] Error 1 > > # gcc -v > Reading specs from /usr/lib64/gcc-lib/x86_64-suse-linux/3.2.2/specs > Configured with: ../configure --enable-threads=posix --prefix=/usr --with-local-prefix=/usr/local --infodir=/usr/share/info --mandir=/usr/share/man --libdir=/usr/lib64 --enable-languages=c,c++,f77,objc,java,ada --enable-libgcj --with-gxx-include-dir=/usr/include/g++ --with-slibdir=/lib --with-system-zlib --enable-shared --enable-__cxa_atexit x86_64-suse-linux > Thread model: posix > gcc version 3.2.2 (SuSE Linux) > > # uname -a > Linux gb0008 2.4.19MARi2c-NUMA #2 Fri Oct 17 06:39:18 PDT 2003 x86_64 unknown > > I don't know if I need this module or not. If I disable i2c-algo-biths in kernel/Module.mk, then I'm able to compile, > > < ifneq ($(shell if grep -q '^CONFIG_I2C_ALGOBITHS=y' $(LINUX)/.config; then echo 1; fi),1) > < KERNELTARGETS += $(MODULE_DIR)/i2c-algo-biths.o > < KERNELINCLUDES += $(MODULE_DIR)/i2c-algo-biths.h > < endif > --- > > #ifneq ($(shell if grep -q '^CONFIG_I2C_ALGOBITHS=y' $(LINUX)/.config; then echo 1; fi),1) > > #KERNELTARGETS += $(MODULE_DIR)/i2c-algo-biths.o > > #KERNELINCLUDES += $(MODULE_DIR)/i2c-algo-biths.h > > #endif > > lm_sensors compiles OK. I can't detect any sensors, though: > > gb0008:/tmp/marc/lm_sensors-2.8.1 # prog/detect/sensors-detect > > This program will help you determine which I2C/SMBus modules you need to > load to use lm_sensors most effectively. You need to have i2c and > lm_sensors installed before running this program. > Also, you need to be `root', or at least have access to the /dev/i2c-* > files, for most things. > If you have patched your kernel and have some drivers built-in, you can > safely answer NO if asked to load some modules. In this case, things may > seem a bit confusing, but they will still work. > > System vendor (DMI): AMD > BIOS version (DMI): PMLC00-7 > We can start with probing for (PCI) I2C or SMBus adapters. > You do not need any special privileges for this. > Do you want to probe now? (YES/no): > gb0008:/tmp/marc/lm_sensors-2.8.1 # lsmod|grep i2 > i2c-proc 9608 0 > i2c-dev 5792 0 > i2c-core 23460 0 [i2c-proc i2c-dev] > gb0008:/tmp/marc/lm_sensors-2.8.1 # rmmod i2c-proc i2c-dev > gb0008:/tmp/marc/lm_sensors-2.8.1 # prog/detect/sensors-detect > > This program will help you determine which I2C/SMBus modules you need to > load to use lm_sensors most effectively. You need to have i2c and > lm_sensors installed before running this program. > Also, you need to be `root', or at least have access to the /dev/i2c-* > files, for most things. > If you have patched your kernel and have some drivers built-in, you can > safely answer NO if asked to load some modules. In this case, things may > seem a bit confusing, but they will still work. > > System vendor (DMI): AMD > BIOS version (DMI): PMLC00-7 > We can start with probing for (PCI) I2C or SMBus adapters. > You do not need any special privileges for this. > Do you want to probe now? (YES/no): > Probing for PCI bus adapters... > Use driver `i2c-amd8111' for device 00:07.2: AMD-8111 SMBus 2.0 > Use driver `i2c-amd756' for device 00:07.3: AMD-8111 ACPI > Probe succesfully concluded. > > We will now try to load each adapter module in turn. > Load `i2c-amd8111' (say NO if built into your kernel)? (YES/no): > Module loaded succesfully. > Load `i2c-amd756' (say NO if built into your kernel)? (YES/no): > /lib/modules/2.4.19MARi2c-NUMA/kernel/drivers/i2c/busses/i2c-amd756.o: init_module: No such device > Hint: insmod errors can be caused by incorrect module parameters, including invalid IO or IRQ parameters. > You may find more information in syslog or the output from dmesg > /lib/modules/2.4.19MARi2c-NUMA/kernel/drivers/i2c/busses/i2c-amd756.o: insmod /lib/modules/2.4.19MARi2c-NUMA/kernel/drivers/i2c/busses/i2c-amd756.o failed > /lib/modules/2.4.19MARi2c-NUMA/kernel/drivers/i2c/busses/i2c-amd756.o: insmod i2c-amd756 failed > Loading failed... skipping. > Do you now want to be prompted for non-detectable adapters? (yes/NO): > To continue, we need module `i2c-dev' to be loaded. > If it is built-in into your kernel, you can safely skip this. > i2c-dev is not loaded. Do you want to load it now? (YES/no): > Module loaded succesfully. > > We are now going to do the adapter probings. Some adapters may hang halfway > through; we can't really help that. Also, some chips will be double detected; > we choose the one with the highest confidence value in that case. > If you found that the adapter hung after probing a certain address, you can > specify that address to remain unprobed. That often > includes address 0x69 (clock chip). > > Next adapter: SMBus2 AMD8111 adapter at 1000 (Non-I2C SMBus 2.0 adapter) > Do you want to scan it? (YES/no/selectively): > Client found at address 0x08 > > Some chips are also accessible through the ISA bus. ISA probes are > typically a bit more dangerous, as we have to write to I/O ports to do > this. Do you want to scan the ISA bus? (YES/no): > Probing for `National Semiconductor LM78' > Trying address 0x0290... Failed! > Probing for `National Semiconductor LM78-J' > Trying address 0x0290... Failed! > Probing for `National Semiconductor LM79' > Trying address 0x0290... Failed! > Probing for `Winbond W83781D' > Trying address 0x0290... Failed! > Probing for `Winbond W83782D' > Trying address 0x0290... Failed! > Probing for `Winbond W83627HF' > Trying address 0x0290... Failed! > Probing for `Winbond W83697HF' > Trying address 0x0290... Failed! > Probing for `Silicon Integrated Systems SIS5595' > Trying general detect... Failed! > Probing for `VIA Technologies VT82C686 Integrated Sensors' > Trying general detect... Failed! > Probing for `VIA Technologies VT8231 Integrated Sensors' > Trying general detect... Failed! > Probing for `ITE IT8705F / IT8712F / SiS 950' > Trying address 0x0290... Failed! > Probing for `IPMI BMC KCS' > Trying address 0x0ca0... Failed! > Probing for `IPMI BMC SMIC' > Trying address 0x0ca8... Failed! > > Some Super I/O chips may also contain sensors. Super I/O probes are > typically a bit more dangerous, as we have to write to I/O ports to do > this. Do you want to scan for Super I/O sensors? (YES/no): > Probing for `SMSC 47M10x Super IO Fan Sensors' > Failed! (0xe1) > Probing for `SMSC 47M14x Super IO Fan Sensors' > Failed! (0xe1) > Probing for `VT1211 Super IO Sensors' > Failed! (0xe1) > Probing for `Winbond W83627HF Super IO Sensors' > Failed! (0xe1) > Probing for `Winbond W83627THF Super IO Sensors' > Failed! (0xe1) > Probing for `Winbond W83697HF Super IO Sensors' > Failed! (0xe1) > > Sorry, no chips were detected. > Either your sensors are not supported, or they are > connected to an I2C bus adapter that we do not support. > See doc/FAQ, doc/lm_sensors-FAQ.html, or > http://www2.lm-sensors.nu/~lm78/cvs/lm_sensors2/doc/lm_sensors-FAQ.html > (FAQ #4.24.3) for further information. > If you find out what chips are on your board, see > http://secure.netroedge.com/~lm78/newdrivers.html for driver status. > > When I try to manually insert the adm1026 module, it inserts but finds nothing, > > # modprobe adm1026 > > adm1026: Version 2.8.1 (20031005) > adm1026: See http://www.penguincomputing.com/lm_sensors for more info. > > # /usr/local/bin/sensors > No sensors found! > > Any suggestions? > > Thanks.
