try CVS which has super I/O detection and a new 83627hf isa driver. Ramesh Ramakrishnan wrote: > hi > > i am having trouble in getting lm_sensor 2.7.0 working on tyan s2720 board with > linux kernel 2.4.19. > > The s2720 onboard hardware monitoring devices include Winbond W83627HF, > Winbond W83782d and two 'on Chip Xeon Thermal Sensor' at address 0x18 and 0x19. > > the i2c-detect script suggest to load the following modules i2c-isa, i2c-i801, w83781d > and eeprom. After loading the suggested modules on running the i2cdetect gives the > following output > > Installed I2C busses: > i2c-0 smbus SMBus I801 adapter at ec80 Non-I2C SMBus adapter > i2c-1 dummy ISA main adapter ISA bus algorithm > > in the lm_sensor mailing list, found an advice to load the adm1021 module to get the > temperature from xeon processor. loaded the adm1021 module on bus 0,0x18. > > running the sensors gives wrong temperature(-1) for adm1021. tried loading the module > in both address 0x18 and 0x19. > > one think i noticed is when i load the i2c-velleman (this module is loaded when during > the sensors-detect script, though the script doesnt suggest to load this module) the i2cdetect > shows up the following result. > > again loading the adm1021 on the i2c bus 2 results the same output(-1). > > Installed I2C busses: > i2c-0 smbus SMBus I801 adapter at ec80 Non-I2C SMBus adapter > i2c-1 dummy ISA main adapter ISA bus algorithm > i2c-2 i2c Velleman K8000 Bit-shift algorithm > > any information is appreciated. > > regards > ramesh > > > the output from i2cdetect > ------------------------- > > w83782d-i2c-0-29 > Adapter: SMBus I801 adapter at ec80 > Algorithm: Non-I2C SMBus adapter > VCore: +1.47 V (min = +1.21 V, max = +1.48 V) > VCC_1.2: +1.13 V (min = +1.21 V, max = +1.48 V) ALARM > 3.3V: +3.42 V (min = +2.97 V, max = +3.63 V) > +5V: +5.07 V (min = +4.50 V, max = +5.48 V) > 12V: +12.16 V (min = +10.79 V, max = +13.11 V) > VCC_2.5: +2.54 V (min = +0.33 V, max = +0.78 V) > VCC_1.8: +1.76 V (min = +0.70 V, max = +1.02 V) > V5SB: +5.11 V (min = +4.50 V, max = +5.48 V) > VBat: +3.24 V (min = +2.70 V, max = +3.29 V) > P1Fan: 0 RPM (min = 895 RPM, div = 2) > P2Fan: 0 RPM (min = 895 RPM, div = 2) > Fan3: 0 RPM (min = 895 RPM, div = 2) > VRM: +74?C (limit = +60?C) sensor = thermistor ALARM > vid: +1.350 V > alarms: Chassis intrusion detection ALARM > beep_enable: > Sound alarm disabled > > w83627hf-isa-0290 > Adapter: ISA adapter > Algorithm: ISA algorithm > Fan4: 0 RPM (min = 1500 RPM, div = 2) > Fan5: 0 RPM (min = 1500 RPM, div = 2) > Fan6: 0 RPM (min = 1500 RPM, div = 2) > vid: +1.350 V > alarms: > beep_enable: > Sound alarm disabled > > adm1021-i2c-0-18 > Adapter: SMBus I801 adapter at ec80 > Algorithm: Non-I2C SMBus adapter > CPU0_Sub: -1?C (min = -1?C, max = -1?C)ALARM (LOW,HIGH) > CPU0: -1?C (min = -1?C, max = -1?C)ALARM (N/A,LOW) > die_code: 255 > >