this is caused by a change made in 2.6.4 to support multiple VID versions; you have new modules but an old libsensors; be sure that libsensors got installed and are seen by ldconfig -v, and that older libsensors are not in a different directory that is being picked up first by ld.so.conf. Steve Snyder wrote: > > One more thing I forgot to mention: the video voltage value is correct in > the /proc filesystem: > > # cat /proc/sys/dev/sensors/w83627hf-isa-0290/vid > 1.350 > > FYI. > > ---------- Forwarded Message ---------- > > Subject: lmsensors displays video voltage incorrectly > Date: Tue, 17 Sep 2002 15:54:59 -0500 > From: Steve Snyder <swsnyder at insightbb.com> > To: sensors at stimpy.netroedge.com > > Hello. > > The video voltage is shown at x10 the actual voltage. > > I have seen this behavior with both the 2.6.5 and 2.6.4 versions of > lmsensors, and with 3 different chips (w83781d-isa-0290, w83782d-isa-0290 > and w83627hf-isa-0290). > > In all permutation of the above software versions and chips, I have been > running Red Hat Linux v7.2 with a stock v2.4.19 kernel The 'sensors' > program and the sensors.conf in use have been from 2.6.4/2.6.5, not the > files from the RH distribution. > > The I2C driver and /proc interface are builtinfo the kernel, while the > i2c-isa and w83781d drivers are loaded as modules. > > Below are a couple of examples. Those 13.50 and 16.500 voltages should > actually be 1.35 and 1.65, respectively. On a thirm machine (not shown > below) a voltage of 2.0 is displayed as 20.00. Hmm. All other reported > values seem reasonable. > > Note that this problem is *not* seen with version 2.6.3 of the lmsensors > package. > > If there is any aditional info I can provide, please let me know. > > Thanks. > > ---------- > # sensors > w83782d-isa-0290 > Adapter: ISA adapter > Algorithm: ISA algorithm > VCore 1: +1.68 V (min = +4.08 V, max = +4.08 V) > VCore 2: +1.68 V (min = +4.08 V, max = +4.08 V) > +3.3V: +3.45 V (min = +2.97 V, max = +3.63 V) > +5V: +5.11 V (min = +4.50 V, max = +5.48 V) > +12V: +12.01 V (min = +10.79 V, max = +13.11 V) > -12V: -12.24 V (min = -13.21 V, max = -10.90 V) > -5V: -5.10 V (min = -5.51 V, max = -4.51 V) > V5SB: +5.11 V (min = +4.50 V, max = +5.48 V) (beep) > VBat: +3.12 V (min = +2.70 V, max = +3.29 V) (beep) > fan1: 4927 RPM (min = 3000 RPM, div = 2) > fan2: 4856 RPM (min = 3000 RPM, div = 2) > fan3: 0 RPM (min = 750 RPM, div = 8) > temp1: +21.0?C (limit = +60?C, hysteresis = +127?C) sensor = > thermistor > temp2: +26?C (limit = +60?C, hysteresis = +50?C) sensor = > thermistor > temp3: +25?C (limit = +60?C, hysteresis = +50?C) sensor = > thermistor > vid: +16.50 V > alarms: Chassis intrusion detection > beep_enable: > Sound alarm disabled > > ---------- > > # prog/sensors/sensors > w83627hf-isa-0290 > Adapter: ISA adapter > Algorithm: ISA algorithm > VCore 1: +1.48 V (min = +4.08 V, max = +4.08 V) > VCore 2: +3.26 V (min = +4.08 V, max = +4.08 V) > +3.3V: +3.24 V (min = +3.13 V, max = +3.45 V) > +5V: +4.80 V (min = +4.72 V, max = +5.24 V) > +12V: +11.89 V (min = +10.79 V, max = +13.19 V) > -12V: -11.62 V (min = -13.21 V, max = -10.90 V) > -5V: -2.09 V (min = -5.26 V, max = -4.76 V) > V5SB: +5.31 V (min = +4.72 V, max = +5.24 V) > VBat: +3.18 V (min = +2.40 V, max = +3.60 V) > fan1: 3443 RPM (min = 3000 RPM, div = 2) > fan2: 3461 RPM (min = 3000 RPM, div = 2) > fan3: 0 RPM (min = 1500 RPM, div = 4) > temp1: +34?C (limit = +60?C) sensor = > thermistor > temp2: +33.0?C (limit = +60?C, hysteresis = +50?C) sensor = > thermistor > temp3: +31.0?C (limit = +60?C, hysteresis = +50?C) sensor = > thermistor > vid: +13.500 V > alarms: Chassis intrusion detection ALARM > beep_enable: > Sound alarm disabled > > ---------- > > -------------------------------------------------------
