thanks. if you get it working all (or most) of the way, please submit it to us for our package. mds "ing. Gert-Jan de Jonge" wrote: > > Hi, > > After following some instructions on the "New drivers" page, I did the > following: > /sbin/modprobe i2c-core > /sbin/modprobe i2c-dev > /sbin/modprobe i2c-piix4 > /sbin/modprobe i2c-proc > /sbin/modprobe adm1025 force_adm1025=0,0x51,0,0x52 > > sensors output showed no correct temperature, after comparing the both > datasheets i noticed the temp registers are located at > different adresses. After playing around with the code of adm1025.c (only > for the temp) I get the following output: > adm1025-i2c-0-51 > Adapter: SMBus PIIX4 adapter at 0580 > Algorithm: Non-I2C SMBus adapter > +2.5V: +0.27 V (min = +2.22 V, max = +2.72 V) > VCore: +0.09 V (min = +1.73 V, max = +1.93 V) > +3.3V: +0.36 V (min = +2.93 V, max = +3.59 V) ALARM > +5V: +0.20 V (min = +4.45 V, max = +5.44 V) ALARM > +12V: +0.00 V (min = +10.68 V, max = +13.06 V) > VCC: +0.00 V (min = +2.93 V, max = +3.59 V) > SYS Temp: +32.0?C (min = +0?C, max = +60?C) ALARM > CPU Temp: +0.0?C (min = +0?C, max = +60?C) ALARM > vid: +1.85 V > > adm1025-i2c-0-52 > Adapter: SMBus PIIX4 adapter at 0580 > Algorithm: Non-I2C SMBus adapter > +2.5V: +0.27 V (min = +2.22 V, max = +2.72 V) > VCore: +0.09 V (min = +1.73 V, max = +1.93 V) > +3.3V: +0.36 V (min = +2.93 V, max = +3.59 V) ALARM > +5V: +0.20 V (min = +4.45 V, max = +5.44 V) ALARM > +12V: +0.00 V (min = +10.68 V, max = +13.06 V) > VCC: +0.00 V (min = +2.93 V, max = +3.59 V) > SYS Temp: +32.0?C (min = +0?C, max = +60?C) ALARM > CPU Temp: +0.0?C (min = +0?C, max = +60?C) ALARM > vid: +1.85 V > > I have not looked at the other values, at this moment i am especially > interested in the temp, because it's causing some problems. ;) > > regards, > Gert-Jan de Jonge > > p.s.: in adm1025.c i changed the following as a test: > ..... > //#define ADM1025_REG_RTEMP 0x26 > #define ADM1025_REG_RTEMP 0x29 > //#define ADM1025_REG_TEMP 0x27 > #define ADM1025_REG_TEMP 0x1F > ..... > //#define ADM1025_REG_RTEMP_HIGH 0x37 > //#define ADM1025_REG_RTEMP_LOW 0x38 > //#define ADM1025_REG_TEMP_HIGH 0x39 > //#define ADM1025_REG_TEMP_LOW 0x3A > #define ADM1025_REG_RTEMP_HIGH 0x41 > #define ADM1025_REG_RTEMP_LOW 0x49 > #define ADM1025_REG_TEMP_HIGH 0x68 > #define ADM1025_REG_TEMP_LOW 0x69 > Gert-Jan de Jonge > http://www.saturnus.nl/~gertjan
