Did sensors-detect find a w83782d? Do you really have a w83782d (look at your board)? send us the output of i2cdump 0 0x2d if it's not all FF's. > Chad McKay wrote: > > > This is the output from the sensors program : > ------ > # sensors > w83782d-i2c-0-2d > Adapter: SMBus PIIX4 adapter at 5000 > Algorithm: Non-I2C SMBus adapter > VCore 1: +4.08 V (min = +4.08 V, max = +4.08 V) > VCore 2: +4.08 V (min = +4.08 V, max = +4.08 V) > +3.3V: +4.08 V (min = +4.08 V, max = +4.08 V) > +5V: +6.85 V (min = +6.85 V, max = +6.85 V) > +12V: +15.50 V (min = +15.50 V, max = +15.50 V) ALARM (beep) > -12V: +6.06 V (min = +6.06 V, max = +6.06 V) ALARM (beep) > -5V: +5.10 V (min = +5.10 V, max = +5.10 V) ALARM (beep) > V5SB: +6.85 V (min = +6.85 V, max = +6.85 V) ALARM (beep) > VBat: +4.08 V (min = +4.08 V, max = +4.08 V) ALARM (beep) > fan1: 0 RPM (min = 0 RPM, div = 128) > fan2: 0 RPM (min = 0 RPM, div = 128) > fan3: 0 RPM (min = 0 RPM, div = 128) ALARM > (beep) > temp1: -1.0?C (limit = -1?C, hysteresis = -1?C) sensor = PII/Celeron diode > temp2: +255.5?C (limit = +256?C, hysteresis = +256?C) sensor = 3904 transistor > temp3: +25.0?C (limit = +60?C, hysteresis = +50?C) sensor = thermistor ALARM (beep) > vid: +0.00 V > alarms: Chassis intrusion detection ALARM (beep) > beep_enable: > Sound alarm enabled > ----- > > None of this is anywhere near correct (obviously?). > > Is this a problem with my system or have I got something configured > wrong. The first time I booted the system the speaker started beeping > after a few seconds and never stopped - however the system runs fine > (65 days uptime at one point). I also ran win2000 on it for about 2 > years with no problems. > > Thanks for your help > > Chad McKay > > Some system info: > > standard /etc/sensors.conf file > > Red Hat Linux release 7.2 (Enigma) > Kernel 2.4.7-10smp on a 2-processor i686 > > lm_sensors installed via RPM > # sensors -v > sensors version 1.3 > > Abit bp6 MB w/ 2 clereron 366 OC @ 550 (same problems @ 366) > > dmesg output: > > Linux version 2.4.7-10smp (bhcompile at stripples.devel.redhat.com) (gcc > version 2.96 20000731 (Red Hat Linux 7.1 2.96-98)) #1 SMP Thu Sep 6 > 17:09:31 EDT 2001 > BIOS-provided physical RAM map: > BIOS-e820: 0000000000000000 - 00000000000a0000 (usable) > BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved) > BIOS-e820: 0000000000100000 - 000000001fff0000 (usable) > BIOS-e820: 000000001fff0000 - 000000001fff3000 (ACPI NVS) > BIOS-e820: 000000001fff3000 - 0000000020000000 (ACPI data) > BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved) > BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved) > BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved) > Scanning bios EBDA for MXT signature > found SMP MP-table at 000f5ae0 > hm, page 000f5000 reserved twice. > hm, page 000f6000 reserved twice. > hm, page 000f1000 reserved twice. > hm, page 000f2000 reserved twice. > On node 0 totalpages: 131056 > zone(0): 4096 pages. > zone(1): 126960 pages. > zone(2): 0 pages. > Intel MultiProcessor Specification v1.1 > Virtual Wire compatibility mode. > OEM ID: OEM00000 Product ID: PROD00000000 APIC at: 0xFEE00000 > Processor #0 Pentium(tm) Pro APIC version 17 > Processor #1 Pentium(tm) Pro APIC version 17 > I/O APIC #2 Version 17 at 0xFEC00000. > Processors: 2 > Kernel command line: ro root=/dev/hda2 > Initializing CPU#0 > Detected 551.260 MHz processor. > Console: colour VGA+ 80x25 > Calibrating delay loop... 1101.00 BogoMIPS > Memory: 510252k/524224k available (1396k kernel code, 11524k reserved, > 102k data, 240k init, 0k highmem) > Dentry-cache hash table entries: 65536 (order: 7, 524288 bytes) > Inode-cache hash table entries: 32768 (order: 6, 262144 bytes) > Mount-cache hash table entries: 8192 (order: 4, 65536 bytes) > Buffer-cache hash table entries: 32768 (order: 5, 131072 bytes) > Page-cache hash table entries: 131072 (order: 8, 1048576 bytes) > CPU: Before vendor init, caps: 0183fbff 00000000 00000000, vendor = 0 > CPU: L1 I cache: 16K, L1 D cache: 16K > CPU: L2 cache: 128K > Intel machine check architecture supported. > Intel machine check reporting enabled on CPU#0. > CPU: After vendor init, caps: 0183fbff 00000000 00000000 00000000 > CPU: After generic, caps: 0183fbff 00000000 00000000 00000000 > CPU: Common caps: 0183fbff 00000000 00000000 00000000 > Enabling fast FPU save and restore... done. > Checking 'hlt' instruction... OK. > POSIX conformance testing by UNIFIX > mtrr: v1.40 (20010327) Richard Gooch (rgooch at atnf.csiro.au) > mtrr: detected mtrr type: Intel > CPU: Before vendor init, caps: 0183fbff 00000000 00000000, vendor = 0 > CPU: L1 I cache: 16K, L1 D cache: 16K > CPU: L2 cache: 128K > Intel machine check reporting enabled on CPU#0. > CPU: After vendor init, caps: 0183fbff 00000000 00000000 00000000 > CPU: After generic, caps: 0183fbff 00000000 00000000 00000000 > CPU: Common caps: 0183fbff 00000000 00000000 00000000 > CPU0: Intel Celeron (Mendocino) stepping 05 > per-CPU timeslice cutoff: 365.65 usecs. > enabled ExtINT on CPU#0 > ESR value before enabling vector: 00000000 > ESR value after enabling vector: 00000000 > Booting processor 1/1 eip 2000 > Initializing CPU#1 > masked ExtINT on CPU#1 > ESR value before enabling vector: 00000000 > ESR value after enabling vector: 00000000 > Calibrating delay loop... 1101.00 BogoMIPS > CPU: Before vendor init, caps: 0183fbff 00000000 00000000, vendor = 0 > CPU: L1 I cache: 16K, L1 D cache: 16K > CPU: L2 cache: 128K > Intel machine check reporting enabled on CPU#1. > CPU: After vendor init, caps: 0183fbff 00000000 00000000 00000000 > CPU: After generic, caps: 0183fbff 00000000 00000000 00000000 > CPU: Common caps: 0183fbff 00000000 00000000 00000000 > CPU1: Intel Celeron (Mendocino) stepping 05 > Total of 2 processors activated (2202.00 BogoMIPS). > ENABLING IO-APIC IRQs > ...changing IO-APIC physical APIC ID to 2 ... ok. > init IO_APIC IRQs > IO-APIC (apicid-pin) 2-0, 2-10, 2-11, 2-12, 2-17, 2-20, 2-21, 2-22, > 2-23 not connected. > ..TIMER: vector=0x31 pin1=2 pin2=0 > number of MP IRQ sources: 16. > number of IO-APIC #2 registers: 24. > testing the IO APIC....................... > > IO APIC #2...... > .... register #00: 02000000 > ....... : physical APIC id: 02 > .... register #01: 00170011 > ....... : max redirection entries: 0017 > ....... : IO APIC version: 0011 > .... register #02: 00000000 > ....... : arbitration: 00 > .... IRQ redirection table: > NR Log Phy Mask Trig IRR Pol Stat Dest Deli Vect: > 00 000 00 1 0 0 0 0 0 0 00 > 01 003 03 0 0 0 0 0 1 1 39 > 02 003 03 0 0 0 0 0 1 1 31 > 03 003 03 0 0 0 0 0 1 1 41 > 04 003 03 0 0 0 0 0 1 1 49 > 05 003 03 0 0 0 0 0 1 1 51 > 06 003 03 0 0 0 0 0 1 1 59 > 07 003 03 0 0 0 0 0 1 1 61 > 08 003 03 0 0 0 0 0 1 1 69 > 09 003 03 0 0 0 0 0 1 1 71 > 0a 000 00 1 0 0 0 0 0 0 00 > 0b 000 00 1 0 0 0 0 0 0 00 > 0c 000 00 1 0 0 0 0 0 0 00 > 0d 003 03 0 0 0 0 0 1 1 79 > 0e 003 03 0 0 0 0 0 1 1 81 > 0f 003 03 0 0 0 0 0 1 1 89 > 10 003 03 1 1 0 1 0 1 1 91 > 11 000 00 1 0 0 0 0 0 0 00 > 12 003 03 1 1 0 1 0 1 1 99 > 13 003 03 1 1 0 1 0 1 1 A1 > 14 000 00 1 0 0 0 0 0 0 00 > 15 000 00 1 0 0 0 0 0 0 00 > 16 000 00 1 0 0 0 0 0 0 00 > 17 000 00 1 0 0 0 0 0 0 00 > IRQ to pin mappings: > IRQ0 -> 0:2 > IRQ1 -> 0:1 > IRQ3 -> 0:3 > IRQ4 -> 0:4 > IRQ5 -> 0:5 > IRQ6 -> 0:6 > IRQ7 -> 0:7 > IRQ8 -> 0:8 > IRQ9 -> 0:9 > IRQ10 -> 0:19 > IRQ11 -> 0:18 > IRQ12 -> 0:16 > IRQ13 -> 0:13 > IRQ14 -> 0:14 > IRQ15 -> 0:15 > .................................... done. > Using local APIC timer interrupts. > calibrating APIC timer ... > ..... CPU clock speed is 551.2717 MHz. > ..... host bus clock speed is 100.2310 MHz. > cpu: 0, clocks: 1002310, slice: 334103 > CPU0<T0:1002304,T1:668192,D:9,S:334103,C:1002310> > cpu: 1, clocks: 1002310, slice: 334103 > CPU1<T0:1002304,T1:334096,D:2,S:334103,C:1002310> > checking TSC synchronization across CPUs: passed. > mtrr: your CPUs had inconsistent fixed MTRR settings > mtrr: probably your BIOS does not setup all CPUs > PCI: PCI BIOS revision 2.10 entry at 0xfb5c0, last bus=1 > PCI: Using configuration type 1 > PCI: Probing PCI hardware > PCI: Using IRQ router PIIX [8086/7110] at 00:07.0 > Limiting direct PCI/PCI transfers. > isapnp: Scanning for PnP cards... > isapnp: No Plug & Play device found > Linux NET4.0 for Linux 2.4 > Based upon Swansea University Computer Society NET3.039 > Initializing RT netlink socket > apm: BIOS version 1.2 Flags 0x07 (Driver version 1.14) > apm: disabled - APM is not SMP safe. > mxt_scan_bios: enter > Starting kswapd v1.8 > VFS: Diskquotas version dquot_6.5.0 initialized > Detected PS/2 Mouse Port. > pty: 2048 Unix98 ptys configured > Serial driver version 5.05c (2001-07-08) with MANY_PORTS MULTIPORT > SHARE_IRQ SERIAL_PCI ISAPNP enabled > ttyS00 at 0x03f8 (irq = 4) is a 16550A > ttyS01 at 0x02f8 (irq = 3) is a 16550A > Real Time Clock Driver v1.10d > block: queued sectors max/low 338757kB/207685kB, 1024 slots per queue > RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize > Uniform Multi-Platform E-IDE driver Revision: 6.31 > ide: Assuming 33MHz PCI bus speed for PIO modes; override with idebus=xx > PIIX4: IDE controller on PCI bus 00 dev 39 > PIIX4: chipset revision 1 > PIIX4: not 100% native mode: will probe irqs later > ide0: BM-DMA at 0xf000-0xf007, BIOS settings: hda:DMA, hdb:pio > ide1: BM-DMA at 0xf008-0xf00f, BIOS settings: hdc:DMA, hdd:pio > HPT366: onboard version of chipset, pin1=1 pin2=2 > HPT366: IDE controller on PCI bus 00 dev 98 > HPT366: chipset revision 1 > HPT366: not 100% native mode: will probe irqs later > ide2: BM-DMA at 0xe000-0xe007, BIOS settings: hde:pio, hdf:pio > HPT366: IDE controller on PCI bus 00 dev 99 > HPT366: chipset revision 1 > HPT366: not 100% native mode: will probe irqs later > ide3: BM-DMA at 0xec00-0xec07, BIOS settings: hdg:pio, hdh:pio > hda: ST38410A, ATA DISK drive > hdc: LTN382, ATAPI CD/DVD-ROM drive > ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 > ide1 at 0x170-0x177,0x376 on irq 15 > hda: 16841664 sectors (8623 MB) w/512KiB Cache, CHS=1048/255/63, > UDMA(33) > ide-floppy driver 0.97 > Partition check: > hda: hda1 hda2 hda3 < hda5 hda6 > > Floppy drive(s): fd0 is 1.44M > FDC 0 is a post-1991 82077 > ide-floppy driver 0.97 > md: md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27 > md: Autodetecting RAID arrays. > md: autorun ... > md: ... autorun DONE. > NET4: Linux TCP/IP 1.0 for NET4.0 > IP Protocols: ICMP, UDP, TCP, IGMP > IP: routing cache hash table of 4096 buckets, 32Kbytes > TCP: Hash tables configured (established 32768 bind 32768) > Linux IP multicast router 0.06 plus PIM-SM > NET4: Unix domain sockets 1.0/SMP for Linux NET4.0. > RAMDISK: Compressed image found at block 0 > Freeing initrd memory: 323k freed > VFS: Mounted root (ext2 filesystem). > Journalled Block Device driver loaded > kjournald starting. Commit interval 5 seconds > EXT3-fs: mounted filesystem with ordered data mode. > Freeing unused kernel memory: 240k freed > Adding Swap: 136512k swap-space (priority -1) > Adding Swap: 519160k swap-space (priority -2) > EXT3 FS 2.4-0.9.8, 25 Aug 2001 on ide0(3,2), internal journal > kjournald starting. Commit interval 5 seconds > EXT3 FS 2.4-0.9.8, 25 Aug 2001 on ide0(3,5), internal journal > EXT3-fs: mounted filesystem with ordered data mode. > kjournald starting. Commit interval 5 seconds > EXT3 FS 2.4-0.9.8, 25 Aug 2001 on ide0(3,6), internal journal > EXT3-fs: mounted filesystem with ordered data mode. > ip_tables: (c)2000 Netfilter core team > ip_conntrack (4095 buckets, 32760 max) > via-rhine.c:v1.10-LK1.1.10 07/12/2001 Written by Donald Becker > http://www.scyld.com/network/via-rhine.html > eth0: VIA VT3043 Rhine at 0xd400, 00:a0:0c:c0:0e:a2, IRQ 10. > eth0: MII PHY found at address 1, status 0x782d advertising 05e1 Link > 0000. > wd.c: Presently autoprobing (not recommended) for a single card. > wd.c:v1.10 9/23/94 Donald Becker (becker at cesdis.gsfc.nasa.gov) > eth1: WD80x3 at 0x280, 00 00 C0 CC 27 1C WD8003, IRQ 3, shared memory > at 0xd0000-0xd1fff. > i2c-core.o: i2c core module > piix4.o version 2.5.5 (20010115) > i2c-core.o: adapter SMBus PIIX4 adapter at 5000 registered as adapter 0. > i2c-piix4.o: PIIX4 bus detected and initialized > sensors.o version 2.5.5 (20010115) > w83781d.o version 2.5.5 (20010115) > i2c-core.o: driver W83781D sensor driver registered. > i2c-core.o: client [W83782D chip] registered to adapter [SMBus PIIX4 > adapter at 5000](pos. 0). > i2c-core.o: client [W83782D subclient] registered to adapter [SMBus > PIIX4 adapter at 5000](pos. 1). > i2c-core.o: client [W83782D subclient] registered to adapter [SMBus > PIIX4 adapter at 5000](pos. 2). > parport0: PC-style at 0x378 [PCSPP,TRISTATE] > parport0: cpp_daisy: aa5500ff(38) > parport0: assign_addrs: aa5500ff(38) > parport0: cpp_daisy: aa5500ff(38) > parport0: assign_addrs: aa5500ff(38)
