Hi Alex, On Tue, Jul 19, 2016 at 12:52 AM, Alexander Aring <aar@xxxxxxxxxxxxxx> wrote: >>> If you have the current debugfs UAPI 1:1 already in some kind of stable >>> bluetooth API then I would give you the BIG advice to fix that and let >>> me look into that. (As far I know there exists idea's only, no >>> implementations). >> >> There is the patches posted by Patrik implementing the management interface: >> >> http://www.spinics.net/lists/linux-bluetooth/msg66486.html >> > Okay, just to be sure here, in the above document: > > Controller ID = hdev(usually var name, struct hci_dev)->id > > Interface Index = dev(usualy var name, struct net_device)->idx > > Is this right? I think so, so my next stuff will base on that. Yep. >> Note that these commands are per interface index, so you would be able >> to have two dongle talking to each other, we could in fact even >> automate this to test with 2 virtual controllers. >> > > We have similar automating testing in 802.15.4 6LoWPAN with virtual > transceiver drivers. > > I always looked somehow for some virtual driver in bluetooth, does this > exist mainline? Take a look at the emulator directory: https://git.kernel.org/cgit/bluetooth/bluez.git/tree/emulator >> It is about priorities, we should concentrate in making it work for >> simpler cases, besides the RFC don't talk about subnets either. >> > > I don't talking about subnets. > > I am talking about "make the connect command per interface". Patrik > works shows the following: > > Add Network Command > =================== > > Command Code: 0x0043 > Controller Index: <controller id> > Command Parameters: Address (6 Octets) > Address_Type (1 Octet) > Return Parameters: Address (6 Octets) > Address_Type (1 Octet) > Interface Index (4 Octets) > > This command is used to connect to establish a network connection > to a remote BTLE node. A pre-requisite is that LE is supported > by the controller, otherwise this command will return a > "not supported" response. > > Possible values for the Address_Type parameter: > 0 Reserved > 1 LE Public > 2 LE Random > > This command generates a Command Complete event on success > or failure. > > Possible errors: Busy > Refused > Invalid Parameters > Not Supported > Invalid Index > Already Connected > > So far I understand, this is "make the connect command per device", the > device in this case is not a "struct net_device" it's "struct hci_dev". > > In the "possible" future case to having multiple interfaces you cannot > say on which interface this connect should be done. With "connect" I > mean the l2cap_chan_connect call. And why would we want more than one one net_dev per hci_dev, the rfc7668 only talks about star topology: https://tools.ietf.org/html/rfc7668#section-2.2 Bluetooth currently don't have support for a mesh topology, and anyway I don't think the userspace would need to be involved in the selection of the netdev since this is beyond the Bluetooth interface. In PAN for example we end up doing one netdev per connection and the which the userspace managing using a bridge. > btw: > Also I don't know what's now the parameters "Address/Address_Type" > source/destination? Is the Input of them equal to the output? That is always the destination address, and we needs its type to know if it is public or private to act accordingly. >> >>> I observed, what I explained above. There exists two "connect" mechanism, >>> these are L2 and L3. >>> >>> With L2 I mean $FIND_OUT_RIGHT_NOT_DEPRECATED_TOOL_IN_BT_UTILITY_DSCHUNGEL >>> leadv/lecc stuff. This prepares somehow that you can say >>> l2cap_chan_connect in the upper-layer to connect to slaves. >>> >>> With l2cap_chan_connect I mean L3 connection, which is the same like >>> what you doing in L2 for L3. It's also not be a MUST, because you can >>> run e.g. above example Node A, B, C, D on L2 and: >>> >>> BTLE 6LoWPAN: A <-> B >>> >>> L2CAP_SOCK: C <-> D >>> >>> or some other mixed scenario. I think you want to still have such behaviour. >>> This would be the same like: A, B, C, D and 6lo0 is connected to A, B. >>> Forget the C, D, make with them whatever you want (_maybe_ namespace with >>> C, D or l2cap_sock). >> >> Im not sure where you are going with l2cap_sock here, yes we can make >> it connect to different peers but usually each peer assumes a role in >> BLE, the central role scans and connect and the peripheral only >> advertise. If you do have more than one controller it should be fine >> to have multiple network interfaces and then perhaps you can bridge >> them together, or not, but this should be controlled via userspace, >> the kernel shall only manage the network interface. >> > > Yes, but the kernel needs an UAPI so the user can control it over userspace. > See above my "make connect per interface" suggestion. This is API is for Bluetooth only, it shall not be mixed with network interface management. -- To unsubscribe from this list: send the line "unsubscribe linux-wpan" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
