Hello.
On 13/08/15 14:22, Alexander Aring wrote:
For supporting regmap, this patch will add more register defines to
prepare a full register dump by regmap debugfs.
Signed-off-by: Alexander Aring <alex.aring@xxxxxxxxx>
---
drivers/net/ieee802154/mrf24j40.c | 68 +++++++++++++++++++++++++++++++++++++++
1 file changed, 68 insertions(+)
diff --git a/drivers/net/ieee802154/mrf24j40.c b/drivers/net/ieee802154/mrf24j40.c
index e92b29a..883f2c9 100644
--- a/drivers/net/ieee802154/mrf24j40.c
+++ b/drivers/net/ieee802154/mrf24j40.c
@@ -29,21 +29,56 @@
#define REG_SADRL 0x03 /* Short address (low) */
#define REG_SADRH 0x04 /* Short address (high) */
#define REG_EADR0 0x05 /* Long address (low) (high is EADR7) */
+#define REG_EADR1 0x06
+#define REG_EADR2 0x07
+#define REG_EADR3 0x08
+#define REG_EADR4 0x09
+#define REG_EADR5 0x0A
+#define REG_EADR6 0x0B
+#define REG_EADR7 0x0C
+#define REG_RXFLUSH 0x0D
+#define REG_ORDER 0x10
#define REG_TXMCR 0x11 /* Transmit MAC control */
+#define REG_ACKTMOUT 0x12
+#define REG_ESLOTG1 0x13
+#define REG_SYMTICKL 0x14
+#define REG_SYMTICKH 0x15
#define REG_PACON0 0x16 /* Power Amplifier Control */
#define REG_PACON1 0x17 /* Power Amplifier Control */
#define REG_PACON2 0x18 /* Power Amplifier Control */
+#define REG_TXBCON0 0x1A
#define REG_TXNCON 0x1B /* Transmit Normal FIFO Control */
+#define REG_TXG1CON 0x1C
+#define REG_TXG2CON 0x1D
+#define REG_ESLOTG23 0x1E
+#define REG_ESLOTG45 0x1F
+#define REG_ESLOTG67 0x20
+#define REG_TXPEND 0x21
+#define REG_WAKECON 0x22
+#define REG_FROMOFFSET 0x23
#define REG_TXSTAT 0x24 /* TX MAC Status Register */
+#define REG_TXBCON1 0x25
+#define REG_GATECLK 0x26
+#define REG_TXTIME 0x27
+#define REG_HSYMTMRL 0x28
+#define REG_HSYMTMRH 0x29
#define REG_SOFTRST 0x2A /* Soft Reset */
+#define REG_SECCON0 0x2C
+#define REG_SECCON1 0x2D
#define REG_TXSTBL 0x2E /* TX Stabilization */
+#define REG_RXSR 0x30
#define REG_INTSTAT 0x31 /* Interrupt Status */
#define REG_INTCON 0x32 /* Interrupt Control */
#define REG_GPIO 0x33 /* GPIO */
#define REG_TRISGPIO 0x34 /* GPIO direction */
+#define REG_SLPACK 0x35
#define REG_RFCTL 0x36 /* RF Control Mode Register */
+#define REG_SECCR2 0x37
+#define REG_BBREG0 0x38
#define REG_BBREG1 0x39 /* Baseband Registers */
#define REG_BBREG2 0x3A /* */
+#define REG_BBREG3 0x3B
+#define REG_BBREG4 0x3C
#define REG_BBREG6 0x3E /* */
#define REG_CCAEDTH 0x3F /* Energy Detection Threshold */
@@ -56,12 +91,45 @@
#define REG_RFCON6 0x206
#define REG_RFCON7 0x207
#define REG_RFCON8 0x208
+#define REG_SLPCAL0 0x209
+#define REG_SLPCAL1 0x20A
+#define REG_SLPCAL2 0x20B
+#define REG_RFSTATE 0x20F
#define REG_RSSI 0x210
#define REG_SLPCON0 0x211 /* Sleep Clock Control Registers */
#define REG_SLPCON1 0x220
#define REG_WAKETIMEL 0x222 /* Wake-up Time Match Value Low */
#define REG_WAKETIMEH 0x223 /* Wake-up Time Match Value High */
+#define REG_REMCNTL 0x224
+#define REG_REMCNTH 0x225
+#define REG_MAINCNT0 0x226
+#define REG_MAINCNT1 0x227
+#define REG_MAINCNT2 0x228
+#define REG_MAINCNT3 0x229
#define REG_TESTMODE 0x22F /* Test mode */
+#define REG_ASSOEAR0 0x230
+#define REG_ASSOEAR1 0x231
+#define REG_ASSOEAR2 0x232
+#define REG_ASSOEAR3 0x233
+#define REG_ASSOEAR4 0x234
+#define REG_ASSOEAR5 0x235
+#define REG_ASSOEAR6 0x236
+#define REG_ASSOEAR7 0x237
+#define REG_ASSOSAR0 0x238
+#define REG_ASSOSAR1 0x239
+#define REG_UNONCE0 0x240
+#define REG_UNONCE1 0x241
+#define REG_UNONCE2 0x242
+#define REG_UNONCE3 0x243
+#define REG_UNONCE4 0x244
+#define REG_UNONCE5 0x245
+#define REG_UNONCE6 0x246
+#define REG_UNONCE7 0x247
+#define REG_UNONCE8 0x248
+#define REG_UNONCE9 0x249
+#define REG_UNONCE10 0x24A
+#define REG_UNONCE11 0x24B
+#define REG_UNONCE12 0x24C
#define REG_RX_FIFO 0x300 /* Receive FIFO */
/* Device configuration: Only channels 11-26 on page 0 are supported. */
This together with the regmap support further down was a big help when
trying to debug what might be the difference between a working setup
from Alex and mine. Dumping the regs, checking for difference and
looking up in the docs what they mean was helpful.
Reviewed-by: Stefan Schmidt <stefan@xxxxxxxxxxxxxxx>
regards
Stefan Schmidt
--
To unsubscribe from this list: send the line "unsubscribe linux-wpan" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
