The MRF24J40MC module has an external amplifier which should be
enabled. The TX power has to be lowered to meet FCC regs.
Signed-off-by: Simon Vincent <simon.vincent@xxxxxxxxxx>
---
v2 -> v3:
* Added extra code comments and removed check of spi return values.
drivers/net/ieee802154/mrf24j40.c | 32 ++++++++++++++++++++++++++++++--
1 file changed, 30 insertions(+), 2 deletions(-)
diff --git a/drivers/net/ieee802154/mrf24j40.c b/drivers/net/ieee802154/mrf24j40.c
index 07e0b88..ff3ca07 100644
--- a/drivers/net/ieee802154/mrf24j40.c
+++ b/drivers/net/ieee802154/mrf24j40.c
@@ -43,6 +43,8 @@
#define REG_TXSTBL 0x2E /* TX Stabilization */
#define REG_INTSTAT 0x31 /* Interrupt Status */
#define REG_INTCON 0x32 /* Interrupt Control */
+#define REG_GPIO 0x33 /* GPIO */
+#define REG_TRISGPIO 0x34 /* GPIO direction */
#define REG_RFCTL 0x36 /* RF Control Mode Register */
#define REG_BBREG1 0x39 /* Baseband Registers */
#define REG_BBREG2 0x3A /* */
@@ -63,6 +65,7 @@
#define REG_SLPCON1 0x220
#define REG_WAKETIMEL 0x222 /* Wake-up Time Match Value Low */
#define REG_WAKETIMEH 0x223 /* Wake-up Time Match Value High */
+#define REG_TESTMODE 0x22F /* Test mode */
#define REG_RX_FIFO 0x300 /* Receive FIFO */
/* Device configuration: Only channels 11-26 on page 0 are supported. */
@@ -75,6 +78,8 @@
#define RX_FIFO_SIZE 144 /* From datasheet */
#define SET_CHANNEL_DELAY_US 192 /* From datasheet */
+enum mrf24j40_modules { MRF24J40, MRF24J40MA, MRF24J40MC };
+
/* Device Private Data */
struct mrf24j40 {
struct spi_device *spi;
@@ -691,6 +696,28 @@ static int mrf24j40_hw_init(struct mrf24j40 *devrec)
if (ret)
goto err_ret;
+ if (spi_get_device_id(devrec->spi)->driver_data == MRF24J40MC) {
+ /* Enable external amplifier.
+ * From MRF24J40MC datasheet section 1.3: Operation.
+ */
+ write_long_reg(devrec, REG_TESTMODE, &val);
+ val |= 0x7; /* Configure GPIO 0-2 to control amplifier */
+ write_long_reg(devrec, REG_TESTMODE, val);
+
+ read_short_reg(devrec, REG_TRISGPIO, &val);
+ val |= 0x8; /* Set GPIO3 as output. */
+ write_short_reg(devrec, REG_TRISGPIO, val);
+
+ read_short_reg(devrec, REG_GPIO, &val);
+ val |= 0x8; /* Set GPIO3 HIGH to enable U5 voltage regulator */
+ write_short_reg(devrec, REG_GPIO, val);
+
+ /* Reduce TX pwr to meet FCC requirements.
+ * From MRF24J40MC datasheet section 3.1.1
+ */
+ write_long_reg(devrec, REG_RFCON3, 0x28);
+ }
+
return 0;
err_ret:
@@ -779,8 +806,9 @@ static int mrf24j40_remove(struct spi_device *spi)
}
static const struct spi_device_id mrf24j40_ids[] = {
- { "mrf24j40", 0 },
- { "mrf24j40ma", 0 },
+ { "mrf24j40", MRF24J40 },
+ { "mrf24j40ma", MRF24J40MA },
+ { "mrf24j40mc", MRF24J40MC },
{ },
};
MODULE_DEVICE_TABLE(spi, mrf24j40_ids);
--
1.9.1
--
To unsubscribe from this list: send the line "unsubscribe linux-wpan" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
