hi there, i can't get the WLAN UB-5 AR5414 (5GHz) to run. i tried: *** ifconfig wlan0 down iw dev wlan0 del iw phy phy0 interface add wlan0 type adhoc iwconfig wlan0 mode ad-hoc essid xxxh ap 00:00:00:78:9a:bc channel 48 ifconfig mesh0 10.10.10.2 up *** and i tried with hostapd ** interface=wlan0 driver=nl80211 ssid=xxx hw_mode=a channel=48 *** nothing happend. i also cant get a dump oft he card. my hardware is alix2d2, debian 6.0.6, kernel 3.6.5, cf install with flashybrid. thanks a lot for help, walter. *** iwconfig root@srv-ldeb-mesh01:~# iwconfig ip_vti0 no wireless extensions. gre0 no wireless extensions. wlan0 IEEE 802.11a Mode:Master Tx-Power=0 dBm Retry long limit:7 RTS thr:off Fragment thr:off Power Management:on lo no wireless extensions. eth0 no wireless extensions. eth1 no wireless extensions. wlan1 IEEE 802.11abgn Mode:Master Tx-Power=20 dBm Retry long limit:7 RTS thr:off Fragment thr:off Power Management:on tunl0 no wireless extensions. *** *** iw list root@srv-ldeb-mesh01:~# iw list Wiphy phy1 Band 1: Frequencies: * 5040 MHz [8] (disabled) * 5060 MHz [12] (disabled) * 5080 MHz [16] (disabled) * 5180 MHz [36] (20.0 dBm) (passive scanning, no IBSS) * 5200 MHz [40] (20.0 dBm) (passive scanning, no IBSS) * 5220 MHz [44] (20.0 dBm) (passive scanning, no IBSS) * 5240 MHz [48] (20.0 dBm) (passive scanning, no IBSS) * 5260 MHz [52] (disabled) * 5280 MHz [56] (disabled) * 5300 MHz [60] (disabled) * 5320 MHz [64] (disabled) * 5500 MHz [100] (disabled) * 5520 MHz [104] (disabled) * 5540 MHz [108] (disabled) * 5560 MHz [112] (disabled) * 5580 MHz [116] (disabled) * 5600 MHz [120] (disabled) * 5620 MHz [124] (disabled) * 5640 MHz [128] (disabled) * 5660 MHz [132] (disabled) * 5680 MHz [136] (disabled) * 5700 MHz [140] (disabled) * 5745 MHz [149] (20.0 dBm) (passive scanning, no IBSS) * 5765 MHz [153] (20.0 dBm) (passive scanning, no IBSS) * 5785 MHz [157] (20.0 dBm) (passive scanning, no IBSS) * 5805 MHz [161] (20.0 dBm) (passive scanning, no IBSS) * 5825 MHz [165] (20.0 dBm) (passive scanning, no IBSS) Bitrates (non-HT): * 6.0 Mbps * 9.0 Mbps * 12.0 Mbps *** *** dmesg |grep ath root@srv-ldeb-mesh01:~# dmesg |grep ath [ 5.429666] openvswitch: Open vSwitch switching datapath [ 14.617030] [<c104e3ff>] ? warn_slowpath_common+0xf2/0x132 [ 14.617218] [<c104e561>] ? warn_slowpath_fmt+0x5d/0x7d [ 17.049225] ath: EEPROM regdomain: 0x0 [ 17.049250] ath: EEPROM indicates default country code should be used [ 17.049263] ath: doing EEPROM country->regdmn map search [ 17.049284] ath: country maps to regdmn code: 0x3a [ 17.049299] ath: Country alpha2 being used: US [ 17.049313] ath: Regpair used: 0x3a [ 17.186484] ieee80211 phy0: Selected rate control algorithm 'ath9k_rate_control' [ 17.188842] Registered led device: ath9k-phy0 [ 17.232418] ath5k 0000:00:0e.0: registered as 'phy1' [ 18.047742] ath: EEPROM regdomain: 0x0 [ 18.047767] ath: EEPROM indicates default country code should be used [ 18.047780] ath: doing EEPROM country->regdmn map search [ 18.047801] ath: country maps to regdmn code: 0x3a [ 18.047816] ath: Country alpha2 being used: US [ 18.047830] ath: Regpair used: 0x3a [ 18.051916] ath5k: phy1: Atheros AR5414 chip found (MAC: 0xa5, PHY: 0x61) root@srv-ldeb-mesh01:~# *** ÿôèº{.nÇ+?·?®??+%?Ëÿ±éݶ¥?wÿº{.nÇ+?·¥?{±ÿ«zW¬³ø§¶?¡Ü¨}©?²Æ zÚ&j:+v?¨þø¯ù®w¥þ?à2?Þ?¨èÚ&¢)ß¡«a¶Úÿÿûàz¿äz¹Þ?ú+?ù???Ý¢jÿ?wèþf