Signed-off-by: Vladimir Kondratiev <qca_vkondrat@xxxxxxxxxxxxxxxx> --- nl80211.h | 180 +++++++++++++++++++++++++++++++++++++++++++------------------ 1 file changed, 127 insertions(+), 53 deletions(-) diff --git a/nl80211.h b/nl80211.h index a6959f7..179bd3a 100644 --- a/nl80211.h +++ b/nl80211.h @@ -170,6 +170,8 @@ * %NL80211_ATTR_CIPHER_GROUP, %NL80211_ATTR_WPA_VERSIONS, * %NL80211_ATTR_AKM_SUITES, %NL80211_ATTR_PRIVACY, * %NL80211_ATTR_AUTH_TYPE and %NL80211_ATTR_INACTIVITY_TIMEOUT. + * The channel to use can be set on the interface or be given using the + * %NL80211_ATTR_WIPHY_FREQ and %NL80211_ATTR_WIPHY_CHANNEL_TYPE attrs. * @NL80211_CMD_NEW_BEACON: old alias for %NL80211_CMD_START_AP * @NL80211_CMD_STOP_AP: Stop AP operation on the given interface * @NL80211_CMD_DEL_BEACON: old alias for %NL80211_CMD_STOP_AP @@ -275,6 +277,12 @@ * @NL80211_CMD_NEW_SURVEY_RESULTS: survey data notification (as a reply to * NL80211_CMD_GET_SURVEY and on the "scan" multicast group) * + * @NL80211_CMD_SET_PMKSA: Add a PMKSA cache entry, using %NL80211_ATTR_MAC + * (for the BSSID) and %NL80211_ATTR_PMKID. + * @NL80211_CMD_DEL_PMKSA: Delete a PMKSA cache entry, using %NL80211_ATTR_MAC + * (for the BSSID) and %NL80211_ATTR_PMKID. + * @NL80211_CMD_FLUSH_PMKSA: Flush all PMKSA cache entries. + * * @NL80211_CMD_REG_CHANGE: indicates to userspace the regulatory domain * has been changed and provides details of the request information * that caused the change such as who initiated the regulatory request @@ -454,6 +462,10 @@ * the frame. * @NL80211_CMD_ACTION_TX_STATUS: Alias for @NL80211_CMD_FRAME_TX_STATUS for * backward compatibility. + * + * @NL80211_CMD_SET_POWER_SAVE: Set powersave, using %NL80211_ATTR_PS_STATE + * @NL80211_CMD_GET_POWER_SAVE: Get powersave status in %NL80211_ATTR_PS_STATE + * * @NL80211_CMD_SET_CQM: Connection quality monitor configuration. This command * is used to configure connection quality monitoring notification trigger * levels. @@ -769,6 +781,13 @@ enum nl80211_commands { * section 7.3.2.25.1, e.g. 0x000FAC04) * @NL80211_ATTR_KEY_SEQ: transmit key sequence number (IV/PN) for TKIP and * CCMP keys, each six bytes in little endian + * @NL80211_ATTR_KEY_DEFAULT: Flag attribute indicating the key is default key + * @NL80211_ATTR_KEY_DEFAULT_MGMT: Flag attribute indicating the key is the + * default management key + * @NL80211_ATTR_CIPHER_SUITES_PAIRWISE: For crypto settings for connect or + * other commands, indicates which pairwise cipher suites are used + * @NL80211_ATTR_CIPHER_SUITE_GROUP: For crypto settings for connect or + * other commands, indicates which group cipher suite is used * * @NL80211_ATTR_BEACON_INTERVAL: beacon interval in TU * @NL80211_ATTR_DTIM_PERIOD: DTIM period for beaconing @@ -1004,6 +1023,8 @@ enum nl80211_commands { * @NL80211_ATTR_ACK: Flag attribute indicating that the frame was * acknowledged by the recipient. * + * @NL80211_ATTR_PS_STATE: powersave state, using &enum nl80211_ps_state values. + * * @NL80211_ATTR_CQM: connection quality monitor configuration in a * nested attribute with %NL80211_ATTR_CQM_* sub-attributes. * @@ -1061,7 +1082,7 @@ enum nl80211_commands { * flag isn't set, the frame will be rejected. This is also used as an * nl80211 capability flag. * - * @NL80211_ATTR_BSS_HTOPMODE: HT operation mode (u16) + * @NL80211_ATTR_BSS_HT_OPMODE: HT operation mode (u16) * * @NL80211_ATTR_KEY_DEFAULT_TYPES: A nested attribute containing flags * attributes, specifying what a key should be set as default as. @@ -1085,10 +1106,10 @@ enum nl80211_commands { * indicate which WoW triggers should be enabled. This is also * used by %NL80211_CMD_GET_WOWLAN to get the currently enabled WoWLAN * triggers. - + * * @NL80211_ATTR_SCHED_SCAN_INTERVAL: Interval between scheduled scan * cycles, in msecs. - + * * @NL80211_ATTR_SCHED_SCAN_MATCH: Nested attribute with one or more * sets of attributes to match during scheduled scans. Only BSSs * that match any of the sets will be reported. These are @@ -1115,7 +1136,7 @@ enum nl80211_commands { * are managed in software: interfaces of these types aren't subject to * any restrictions in their number or combinations. * - * @%NL80211_ATTR_REKEY_DATA: nested attribute containing the information + * @NL80211_ATTR_REKEY_DATA: nested attribute containing the information * necessary for GTK rekeying in the device, see &enum nl80211_rekey_data. * * @NL80211_ATTR_SCAN_SUPP_RATES: rates per to be advertised as supported in scan, @@ -1182,7 +1203,6 @@ enum nl80211_commands { * @NL80211_ATTR_FEATURE_FLAGS: This u32 attribute contains flags from * &enum nl80211_feature_flags and is advertised in wiphy information. * @NL80211_ATTR_PROBE_RESP_OFFLOAD: Indicates that the HW responds to probe - * * requests while operating in AP-mode. * This attribute holds a bitmap of the supported protocols for * offloading (see &enum nl80211_probe_resp_offload_support_attr). @@ -1520,6 +1540,11 @@ enum nl80211_attrs { #define NL80211_MAX_NR_CIPHER_SUITES 5 #define NL80211_MAX_NR_AKM_SUITES 2 +#define NL80211_MIN_REMAIN_ON_CHANNEL_TIME 10 + +/* default RSSI threshold for scan results if none specified. */ +#define NL80211_SCAN_RSSI_THOLD_OFF -300 + /** * enum nl80211_iftype - (virtual) interface types * @@ -1613,12 +1638,19 @@ struct nl80211_sta_flag_update { * * These attribute types are used with %NL80211_STA_INFO_TXRATE * when getting information about the bitrate of a station. + * There are 2 types for bitrate, legacy one that represents + * 16-bit value, and new one that represents 32-bit value. + * If rate value fits into 16 bit, both attributes reported with + * the same value. If rate is too high to fit into 16 bit (>6.5535Gbps), + * only new value included. + * User space tools encouraged to use new bitrate. * * @__NL80211_RATE_INFO_INVALID: attribute number 0 is reserved * @NL80211_RATE_INFO_BITRATE: total bitrate (u16, 100kbit/s) * @NL80211_RATE_INFO_MCS: mcs index for 802.11n (u8) * @NL80211_RATE_INFO_40_MHZ_WIDTH: 40 Mhz dualchannel bitrate * @NL80211_RATE_INFO_SHORT_GI: 400ns guard interval + * @NL80211_RATE_INFO_BITRATE32: total bitrate (u32, 100kbit/s) * @NL80211_RATE_INFO_MAX: highest rate_info number currently defined * @__NL80211_RATE_INFO_AFTER_LAST: internal use */ @@ -1628,6 +1660,7 @@ enum nl80211_rate_info { NL80211_RATE_INFO_MCS, NL80211_RATE_INFO_40_MHZ_WIDTH, NL80211_RATE_INFO_SHORT_GI, + NL80211_RATE_INFO_BITRATE32, /* keep last */ __NL80211_RATE_INFO_AFTER_LAST, @@ -1788,6 +1821,9 @@ enum nl80211_mpath_info { * @NL80211_BAND_ATTR_HT_CAPA: HT capabilities, as in the HT information IE * @NL80211_BAND_ATTR_HT_AMPDU_FACTOR: A-MPDU factor, as in 11n * @NL80211_BAND_ATTR_HT_AMPDU_DENSITY: A-MPDU density, as in 11n + * @NL80211_BAND_ATTR_VHT_MCS_SET: 32-byte attribute containing the MCS set as + * defined in 802.11ac + * @NL80211_BAND_ATTR_VHT_CAPA: VHT capabilities, as in the HT information IE * @NL80211_BAND_ATTR_MAX: highest band attribute currently defined * @__NL80211_BAND_ATTR_AFTER_LAST: internal use */ @@ -1801,6 +1837,9 @@ enum nl80211_band_attr { NL80211_BAND_ATTR_HT_AMPDU_FACTOR, NL80211_BAND_ATTR_HT_AMPDU_DENSITY, + NL80211_BAND_ATTR_VHT_MCS_SET, + NL80211_BAND_ATTR_VHT_CAPA, + /* keep last */ __NL80211_BAND_ATTR_AFTER_LAST, NL80211_BAND_ATTR_MAX = __NL80211_BAND_ATTR_AFTER_LAST - 1 @@ -1952,6 +1991,8 @@ enum nl80211_reg_rule_attr { * @__NL80211_SCHED_SCAN_MATCH_ATTR_INVALID: attribute number 0 is reserved * @NL80211_SCHED_SCAN_MATCH_ATTR_SSID: SSID to be used for matching, * only report BSS with matching SSID. + * @NL80211_SCHED_SCAN_MATCH_ATTR_RSSI: RSSI threshold (in dBm) for reporting a + * BSS in scan results. Filtering is turned off if not specified. * @NL80211_SCHED_SCAN_MATCH_ATTR_MAX: highest scheduled scan filter * attribute number currently defined * @__NL80211_SCHED_SCAN_MATCH_ATTR_AFTER_LAST: internal use @@ -1959,7 +2000,8 @@ enum nl80211_reg_rule_attr { enum nl80211_sched_scan_match_attr { __NL80211_SCHED_SCAN_MATCH_ATTR_INVALID, - NL80211_ATTR_SCHED_SCAN_MATCH_SSID, + NL80211_SCHED_SCAN_MATCH_ATTR_SSID, + NL80211_SCHED_SCAN_MATCH_ATTR_RSSI, /* keep last */ __NL80211_SCHED_SCAN_MATCH_ATTR_AFTER_LAST, @@ -1967,6 +2009,9 @@ enum nl80211_sched_scan_match_attr { __NL80211_SCHED_SCAN_MATCH_ATTR_AFTER_LAST - 1 }; +/* only for backward compatibility */ +#define NL80211_ATTR_SCHED_SCAN_MATCH_SSID NL80211_SCHED_SCAN_MATCH_ATTR_SSID + /** * enum nl80211_reg_rule_flags - regulatory rule flags * @@ -2086,78 +2131,91 @@ enum nl80211_mntr_flags { * @__NL80211_MESHCONF_INVALID: internal use * * @NL80211_MESHCONF_RETRY_TIMEOUT: specifies the initial retry timeout in - * millisecond units, used by the Peer Link Open message + * millisecond units, used by the Peer Link Open message * * @NL80211_MESHCONF_CONFIRM_TIMEOUT: specifies the initial confirm timeout, in - * millisecond units, used by the peer link management to close a peer link + * millisecond units, used by the peer link management to close a peer link * * @NL80211_MESHCONF_HOLDING_TIMEOUT: specifies the holding timeout, in - * millisecond units + * millisecond units * * @NL80211_MESHCONF_MAX_PEER_LINKS: maximum number of peer links allowed - * on this mesh interface + * on this mesh interface * * @NL80211_MESHCONF_MAX_RETRIES: specifies the maximum number of peer link - * open retries that can be sent to establish a new peer link instance in a - * mesh + * open retries that can be sent to establish a new peer link instance in a + * mesh * * @NL80211_MESHCONF_TTL: specifies the value of TTL field set at a source mesh - * point. + * point. * * @NL80211_MESHCONF_AUTO_OPEN_PLINKS: whether we should automatically - * open peer links when we detect compatible mesh peers. + * open peer links when we detect compatible mesh peers. * * @NL80211_MESHCONF_HWMP_MAX_PREQ_RETRIES: the number of action frames - * containing a PREQ that an MP can send to a particular destination (path - * target) + * containing a PREQ that an MP can send to a particular destination (path + * target) * * @NL80211_MESHCONF_PATH_REFRESH_TIME: how frequently to refresh mesh paths - * (in milliseconds) + * (in milliseconds) * * @NL80211_MESHCONF_MIN_DISCOVERY_TIMEOUT: minimum length of time to wait - * until giving up on a path discovery (in milliseconds) + * until giving up on a path discovery (in milliseconds) * * @NL80211_MESHCONF_HWMP_ACTIVE_PATH_TIMEOUT: The time (in TUs) for which mesh - * points receiving a PREQ shall consider the forwarding information from the - * root to be valid. (TU = time unit) + * points receiving a PREQ shall consider the forwarding information from + * the root to be valid. (TU = time unit) * * @NL80211_MESHCONF_HWMP_PREQ_MIN_INTERVAL: The minimum interval of time (in - * TUs) during which an MP can send only one action frame containing a PREQ - * reference element + * TUs) during which an MP can send only one action frame containing a PREQ + * reference element * * @NL80211_MESHCONF_HWMP_NET_DIAM_TRVS_TIME: The interval of time (in TUs) - * that it takes for an HWMP information element to propagate across the mesh + * that it takes for an HWMP information element to propagate across the + * mesh * * @NL80211_MESHCONF_HWMP_ROOTMODE: whether root mode is enabled or not * * @NL80211_MESHCONF_ELEMENT_TTL: specifies the value of TTL field set at a - * source mesh point for path selection elements. + * source mesh point for path selection elements. * * @NL80211_MESHCONF_HWMP_RANN_INTERVAL: The interval of time (in TUs) between - * root announcements are transmitted. + * root announcements are transmitted. * * @NL80211_MESHCONF_GATE_ANNOUNCEMENTS: Advertise that this mesh station has - * access to a broader network beyond the MBSS. This is done via Root - * Announcement frames. + * access to a broader network beyond the MBSS. This is done via Root + * Announcement frames. * * @NL80211_MESHCONF_HWMP_PERR_MIN_INTERVAL: The minimum interval of time (in - * TUs) during which a mesh STA can send only one Action frame containing a - * PERR element. + * TUs) during which a mesh STA can send only one Action frame containing a + * PERR element. * * @NL80211_MESHCONF_FORWARDING: set Mesh STA as forwarding or non-forwarding - * or forwarding entity (default is TRUE - forwarding entity) + * or forwarding entity (default is TRUE - forwarding entity) * * @NL80211_MESHCONF_RSSI_THRESHOLD: RSSI threshold in dBm. This specifies the - * threshold for average signal strength of candidate station to establish - * a peer link. - * - * @NL80211_MESHCONF_ATTR_MAX: highest possible mesh configuration attribute + * threshold for average signal strength of candidate station to establish + * a peer link. * * @NL80211_MESHCONF_SYNC_OFFSET_MAX_NEIGHBOR: maximum number of neighbors - * to synchronize to for 11s default synchronization method (see 11C.12.2.2) + * to synchronize to for 11s default synchronization method + * (see 11C.12.2.2) * * @NL80211_MESHCONF_HT_OPMODE: set mesh HT protection mode. * + * @NL80211_MESHCONF_ATTR_MAX: highest possible mesh configuration attribute + * + * @NL80211_MESHCONF_HWMP_PATH_TO_ROOT_TIMEOUT: The time (in TUs) for + * which mesh STAs receiving a proactive PREQ shall consider the forwarding + * information to the root mesh STA to be valid. + * + * @NL80211_MESHCONF_HWMP_ROOT_INTERVAL: The interval of time (in TUs) between + * proactive PREQs are transmitted. + * + * @NL80211_MESHCONF_HWMP_CONFIRMATION_INTERVAL: The minimum interval of time + * (in TUs) during which a mesh STA can send only one Action frame + * containing a PREQ element for root path confirmation. + * * @__NL80211_MESHCONF_ATTR_AFTER_LAST: internal use */ enum nl80211_meshconf_params { @@ -2184,6 +2242,9 @@ enum nl80211_meshconf_params { NL80211_MESHCONF_RSSI_THRESHOLD, NL80211_MESHCONF_SYNC_OFFSET_MAX_NEIGHBOR, NL80211_MESHCONF_HT_OPMODE, + NL80211_MESHCONF_HWMP_PATH_TO_ROOT_TIMEOUT, + NL80211_MESHCONF_HWMP_ROOT_INTERVAL, + NL80211_MESHCONF_HWMP_CONFIRMATION_INTERVAL, /* keep last */ __NL80211_MESHCONF_ATTR_AFTER_LAST, @@ -2199,34 +2260,36 @@ enum nl80211_meshconf_params { * @__NL80211_MESH_SETUP_INVALID: Internal use * * @NL80211_MESH_SETUP_ENABLE_VENDOR_PATH_SEL: Enable this option to use a - * vendor specific path selection algorithm or disable it to use the default - * HWMP. + * vendor specific path selection algorithm or disable it to use the + * default HWMP. * * @NL80211_MESH_SETUP_ENABLE_VENDOR_METRIC: Enable this option to use a - * vendor specific path metric or disable it to use the default Airtime - * metric. + * vendor specific path metric or disable it to use the default Airtime + * metric. * * @NL80211_MESH_SETUP_IE: Information elements for this mesh, for instance, a - * robust security network ie, or a vendor specific information element that - * vendors will use to identify the path selection methods and metrics in use. + * robust security network ie, or a vendor specific information element + * that vendors will use to identify the path selection methods and + * metrics in use. * * @NL80211_MESH_SETUP_USERSPACE_AUTH: Enable this option if an authentication - * daemon will be authenticating mesh candidates. + * daemon will be authenticating mesh candidates. * * @NL80211_MESH_SETUP_USERSPACE_AMPE: Enable this option if an authentication - * daemon will be securing peer link frames. AMPE is a secured version of Mesh - * Peering Management (MPM) and is implemented with the assistance of a - * userspace daemon. When this flag is set, the kernel will send peer - * management frames to a userspace daemon that will implement AMPE - * functionality (security capabilities selection, key confirmation, and key - * management). When the flag is unset (default), the kernel can autonomously - * complete (unsecured) mesh peering without the need of a userspace daemon. - * - * @NL80211_MESH_SETUP_ATTR_MAX: highest possible mesh setup attribute number + * daemon will be securing peer link frames. AMPE is a secured version of + * Mesh Peering Management (MPM) and is implemented with the assistance of + * a userspace daemon. When this flag is set, the kernel will send peer + * management frames to a userspace daemon that will implement AMPE + * functionality (security capabilities selection, key confirmation, and + * key management). When the flag is unset (default), the kernel can + * autonomously complete (unsecured) mesh peering without the need of a + * userspace daemon. * * @NL80211_MESH_SETUP_ENABLE_VENDOR_SYNC: Enable this option to use a - * vendor specific synchronization method or disable it to use the default - * neighbor offset synchronization + * vendor specific synchronization method or disable it to use the default + * neighbor offset synchronization + * + * @NL80211_MESH_SETUP_ATTR_MAX: highest possible mesh setup attribute number * * @__NL80211_MESH_SETUP_ATTR_AFTER_LAST: Internal use */ @@ -2490,12 +2553,19 @@ enum nl80211_tx_rate_attributes { * enum nl80211_band - Frequency band * @NL80211_BAND_2GHZ: 2.4 GHz ISM band * @NL80211_BAND_5GHZ: around 5 GHz band (4.9 - 5.7 GHz) + * @NL80211_BAND_60GHZ: around 60 GHz band (58.32 - 64.80 GHz) */ enum nl80211_band { NL80211_BAND_2GHZ, NL80211_BAND_5GHZ, + NL80211_BAND_60GHZ, }; +/** + * enum nl80211_ps_state - powersave state + * @NL80211_PS_DISABLED: powersave is disabled + * @NL80211_PS_ENABLED: powersave is enabled + */ enum nl80211_ps_state { NL80211_PS_DISABLED, NL80211_PS_ENABLED, @@ -2534,10 +2604,14 @@ enum nl80211_attr_cqm { * configured threshold * @NL80211_CQM_RSSI_THRESHOLD_EVENT_HIGH: The RSSI is higher than the * configured threshold + * @NL80211_CQM_RSSI_BEACON_LOSS_EVENT: The device experienced beacon loss. + * (Note that deauth/disassoc will still follow if the AP is not + * available. This event might get used as roaming event, etc.) */ enum nl80211_cqm_rssi_threshold_event { NL80211_CQM_RSSI_THRESHOLD_EVENT_LOW, NL80211_CQM_RSSI_THRESHOLD_EVENT_HIGH, + NL80211_CQM_RSSI_BEACON_LOSS_EVENT, }; -- 1.7.9.5 -- To unsubscribe from this list: send the line "unsubscribe linux-wireless" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html