Hi All, Can ath6kl support AP mode? If yes, how to config it? I tried a simplest config, but can't find the AP. I tried ath6kl driver in git://github.com/kvalo/ath6kl.git and the standard kernel 3.3-rc3. I am sure the HW is OK, wpa_supplicant works for me. hostapd & wpa_supplicant is the latest version build form git://w1.fi/srv/git/hostap.git, hostapd -v hostapd v1.0-rc2 User space daemon for IEEE 802.11 AP management, IEEE 802.1X/WPA/WPA2/EAP/RADIUS Authenticator Copyright (c) 2002-2012, Jouni Malinen <j@xxxxx> and contributors Firmware is form linux-firmware, here is the kernel log: [ 14.534308] mmc1: new high speed SDIO card at address 0001 [ 15.245538] ath6kl: ar6003 hw 2.1.1 sdio fw 3.1.1.609 I used the simplest config: cat /etc/hostapd.conf #change wlan0 to your wireless device interface=wlan0 driver=nl80211 ssid=test channel=1 here is the log: hostapd -d /etc/hostapd.conf random: Trying to read entropy from /dev/random Configuration file: /etc/hostapd.conf nl80211: interface wlan0 in phy phy0 rfkill: initial event: idx=0 type=1 op=0 soft=0 hard=0 nl80211: Using driver-based roaming nl80211: Add own interface ifindex 3 nl80211: Set mode ifindex 3 iftype 3 (AP) nl80211: Create interface iftype 6 (MONITOR) Failed to create interface mon.wlan0: -95 (Operation not supported) nl80211: Driver does not support monitor interface type - try to run without it BSS count 1, BSSID mask 00:00:00:00:00:00 (0 bits) nl80211: Regulatory information - country=00 nl80211: 2402-2472 @ 40 MHz nl80211: 2457-2482 @ 20 MHz nl80211: 2474-2494 @ 20 MHz nl80211: 5170-5250 @ 40 MHz nl80211: 5735-5835 @ 40 MHz nl80211: Added 802.11b mode based on 802.11g information Completing interface initialization Mode: IEEE 802.11b Channel: 1 Frequency: 2412 MHz nl80211: Set freq 2412 (ht_enabled=0 sec_channel_offset=0) Failed to update rate sets in kernel module RATE[0] rate=10 flags=0x1 RATE[1] rate=20 flags=0x1 RATE[2] rate=55 flags=0x0 RATE[3] rate=110 flags=0x0 Flushing old station entries Could not connect to kernel driver. Deauthenticate all stations nl80211: Frame command failed: ret=-22 (Invalid argument) (freq=0 wait=0) wpa_driver_nl80211_set_key: ifindex=3 alg=0 addr=(nil) key_idx=0 set_tx=0 seq_len=0 key_len=0 wpa_driver_nl80211_set_key: ifindex=3 alg=0 addr=(nil) key_idx=1 set_tx=0 seq_len=0 key_len=0 wpa_driver_nl80211_set_key: ifindex=3 alg=0 addr=(nil) key_idx=2 set_tx=0 seq_len=0 key_len=0 wpa_driver_nl80211_set_key: ifindex=3 alg=0 addr=(nil) key_idx=3 set_tx=0 seq_len=0 key_len=0 Using interface wlan0 with hwaddr 00:03:7f:be:f0:a0 and ssid 'test' nl80211: Set beacon (beacon_set=0) nl80211: Ignore AP isolation configuration error since isolation is not used wpa_driver_nl80211_set_operstate: operstate 0->1 (UP) netlink: Operstate: linkmode=-1, operstate=6 Failed to set TX queue parameters for queue 0. Failed to set TX queue parameters for queue 1. Failed to set TX queue parameters for queue 2. Failed to set TX queue parameters for queue 3. wlan0: Setup of interface done. RTM_NEWLINK: operstate=1 ifi_flags=0x1003 ([UP]) RTM_NEWLINK, IFLA_IFNAME: Interface 'wlan0' added Unknown event 5 Best Regards! Tony -- To unsubscribe from this list: send the line "unsubscribe linux-wireless" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
