From: Mohammed Shafi Shajakhan <mohammed@xxxxxxxxxxxxxxxx>
here we check for BT state and if BT calibration has started,
give 25ms for BT Calibration to finish. we also take care of 2G/5G
switch and LNA transfer incase WLAN is operating in 5G. in case the BT
state is awake when we do WLAN calibration re-calibrate and we reset
the message exchange between WLAN and BT. BT is given preference when
simultaneous CAL request happens. calibration for WLAN/BT is done
assuming that the other co-existing module is in awake state, if not
we continue to do calibration while if the other module's state changes
we need to do restart the calibration handshake
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@xxxxxxxxxxxxxxxx>
---
drivers/net/wireless/ath/ath9k/hw.c | 132 +++++++++++++++++++++++++++++++++++
1 files changed, 132 insertions(+), 0 deletions(-)
diff --git a/drivers/net/wireless/ath/ath9k/hw.c b/drivers/net/wireless/ath/ath9k/hw.c
index 1d71d1b..e2860d7 100644
--- a/drivers/net/wireless/ath/ath9k/hw.c
+++ b/drivers/net/wireless/ath/ath9k/hw.c
@@ -1514,6 +1514,7 @@ int ath9k_hw_reset(struct ath_hw *ah, struct ath9k_channel *chan,
struct ath9k_hw_cal_data *caldata, bool bChannelChange)
{
struct ath_common *common = ath9k_hw_common(ah);
+ struct ath9k_hw_mci *mci_hw = &ah->btcoex_hw.mci;
u32 saveLedState;
struct ath9k_channel *curchan = ah->curchan;
u32 saveDefAntenna;
@@ -1521,6 +1522,53 @@ int ath9k_hw_reset(struct ath_hw *ah, struct ath9k_channel *chan,
u64 tsf = 0;
int i, r;
bool allow_fbs = false;
+ bool mci = !!(ah->caps.hw_caps & ATH9K_HW_CAP_MCI);
+ bool save_fullsleep = ah->chip_fullsleep;
+
+ if (mci) {
+
+ ar9003_mci_2g5g_changed(ah, IS_CHAN_2GHZ(chan));
+
+ if (mci_hw->bt_state == MCI_BT_CAL_START) {
+ u32 payload[4] = {0, 0, 0, 0};
+
+ ath_dbg(common, ATH_DBG_MCI, "MCI stop rx for BT CAL");
+
+ mci_hw->bt_state = MCI_BT_CAL;
+
+ /*
+ * MCI FIX: disable mci interrupt here. This is to avoid
+ * SW_MSG_DONE or RX_MSG bits to trigger MCI_INT and
+ * lead to mci_intr reentry.
+ */
+
+ ar9003_mci_disable_interrupt(ah);
+
+ ath_dbg(common, ATH_DBG_MCI, "send WLAN_CAL_GRANT");
+ MCI_GPM_SET_CAL_TYPE(payload, MCI_GPM_WLAN_CAL_GRANT);
+ ar9003_mci_send_message(ah, MCI_GPM, 0, payload,
+ 16, true, false);
+
+ ath_dbg(common, ATH_DBG_MCI, "\nMCI BT is calibrating");
+
+ /* Wait BT calibration to be completed for 25ms */
+
+ if (ar9003_mci_wait_for_gpm(ah, MCI_GPM_BT_CAL_DONE,
+ 0, 25000))
+ ath_dbg(common, ATH_DBG_MCI,
+ "MCI got BT_CAL_DONE\n");
+ else
+ ath_dbg(common, ATH_DBG_MCI,
+ "MCI ### BT cal takes to long, force"
+ "bt_state to be bt_awake\n");
+ mci_hw->bt_state = MCI_BT_AWAKE;
+ /* MCI FIX: enable mci interrupt here */
+ ar9003_mci_enable_interrupt(ah);
+
+ return true;
+ }
+ }
+
if (!ath9k_hw_setpower(ah, ATH9K_PM_AWAKE))
return -EIO;
@@ -1558,12 +1606,29 @@ int ath9k_hw_reset(struct ath_hw *ah, struct ath9k_channel *chan,
if (ath9k_hw_channel_change(ah, chan)) {
ath9k_hw_loadnf(ah, ah->curchan);
ath9k_hw_start_nfcal(ah, true);
+ if (mci && mci_hw->ready)
+ ar9003_mci_2g5g_switch(ah, true);
+
if (AR_SREV_9271(ah))
ar9002_hw_load_ani_reg(ah, chan);
return 0;
}
}
+ if (mci) {
+ ar9003_mci_disable_interrupt(ah);
+
+ if (mci_hw->ready && !save_fullsleep) {
+ ar9003_mci_mute_bt(ah);
+ udelay(20);
+ REG_WRITE(ah, AR_BTCOEX_CTRL, 0);
+ }
+
+ mci_hw->bt_state = MCI_BT_SLEEP;
+ mci_hw->ready = false;
+ }
+
+
saveDefAntenna = REG_READ(ah, AR_DEF_ANTENNA);
if (saveDefAntenna == 0)
saveDefAntenna = 1;
@@ -1619,6 +1684,9 @@ int ath9k_hw_reset(struct ath_hw *ah, struct ath9k_channel *chan,
if (r)
return r;
+ if (mci)
+ ar9003_mci_reset(ah, false, IS_CHAN_2GHZ(chan), save_fullsleep);
+
/*
* Some AR91xx SoC devices frequently fail to accept TSF writes
* right after the chip reset. When that happens, write a new
@@ -1736,6 +1804,55 @@ int ath9k_hw_reset(struct ath_hw *ah, struct ath9k_channel *chan,
ath9k_hw_loadnf(ah, chan);
ath9k_hw_start_nfcal(ah, true);
+ if (mci && mci_hw->ready) {
+
+ if (IS_CHAN_2GHZ(chan) &&
+ (mci_hw->bt_state == MCI_BT_SLEEP)) {
+
+ if (ar9003_mci_check_int(ah,
+ AR_MCI_INTERRUPT_RX_MSG_REMOTE_RESET) ||
+ ar9003_mci_check_int(ah,
+ AR_MCI_INTERRUPT_RX_MSG_REQ_WAKE)) {
+
+ /*
+ * BT is sleeping. Check if BT wakes up during
+ * WLAN calibration. If BT wakes up during
+ * WLAN calibration, need to go through all
+ * message exchanges again and recal.
+ */
+
+ ath_dbg(common, ATH_DBG_MCI, "MCI BT wakes up"
+ "during WLAN calibration\n");
+
+ REG_WRITE(ah, AR_MCI_INTERRUPT_RX_MSG_RAW,
+ AR_MCI_INTERRUPT_RX_MSG_REMOTE_RESET |
+ AR_MCI_INTERRUPT_RX_MSG_REQ_WAKE);
+ ath_dbg(common, ATH_DBG_MCI, "MCI send"
+ "REMOTE_RESET\n");
+ ar9003_mci_remote_reset(ah, true);
+ ar9003_mci_send_sys_waking(ah, true);
+ udelay(1);
+ if (IS_CHAN_2GHZ(chan))
+ ar9003_mci_send_lna_transfer(ah, true);
+
+ mci_hw->bt_state = MCI_BT_AWAKE;
+
+ ath_dbg(common, ATH_DBG_MCI, "MCI re-cal\n");
+
+ if (caldata) {
+ caldata->done_txiqcal_once = false;
+ caldata->done_txclcal_once = false;
+ caldata->rtt_hist.num_readings = 0;
+ }
+
+ if (!ath9k_hw_init_cal(ah, chan))
+ return -EIO;
+
+ }
+ }
+ ar9003_mci_enable_interrupt(ah);
+ }
+
ENABLE_REGWRITE_BUFFER(ah);
ath9k_hw_restore_chainmask(ah);
@@ -1778,6 +1895,21 @@ int ath9k_hw_reset(struct ath_hw *ah, struct ath9k_channel *chan,
if (ah->btcoex_hw.enabled)
ath9k_hw_btcoex_enable(ah);
+ if (mci && mci_hw->ready) {
+ /*
+ * check BT state again to make
+ * sure it's not changed.
+ */
+
+ ar9003_mci_sync_bt_state(ah);
+ ar9003_mci_2g5g_switch(ah, true);
+
+ if ((mci_hw->bt_state == MCI_BT_AWAKE) &&
+ (mci_hw->query_bt == true)) {
+ mci_hw->need_flush_btinfo = true;
+ }
+ }
+
if (AR_SREV_9300_20_OR_LATER(ah)) {
ar9003_hw_bb_watchdog_config(ah);
--
1.7.0.4
--
To unsubscribe from this list: send the line "unsubscribe linux-wireless" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
