Support the fast channel change across band switch only when there
are available of reusable cabliration results. And also observed that
doing agc control calibration on fastcc, sometimes causing calibration
timeout. Hence changing agc control to be run only on full chip reset.
Signed-off-by: Rajkumar Manoharan <rmanohar@xxxxxxxxxxxxxxxx>
---
drivers/net/wireless/ath/ath9k/ar9003_calib.c | 3 +--
drivers/net/wireless/ath/ath9k/hw.c | 14 ++++++++++++--
drivers/net/wireless/ath/ath9k/hw.h | 1 +
3 files changed, 14 insertions(+), 4 deletions(-)
diff --git a/drivers/net/wireless/ath/ath9k/ar9003_calib.c b/drivers/net/wireless/ath/ath9k/ar9003_calib.c
index 47f140c..16851cb 100644
--- a/drivers/net/wireless/ath/ath9k/ar9003_calib.c
+++ b/drivers/net/wireless/ath/ath9k/ar9003_calib.c
@@ -1008,8 +1008,7 @@ static bool ar9003_hw_init_cal(struct ath_hw *ah,
REG_WRITE(ah, AR_PHY_ACTIVE, AR_PHY_ACTIVE_EN);
skip_tx_iqcal:
-
- if (run_agc_cal) {
+ if (run_agc_cal || !(ah->ah_flags & AH_FASTCC)) {
/* Calibrate the AGC */
REG_WRITE(ah, AR_PHY_AGC_CONTROL,
REG_READ(ah, AR_PHY_AGC_CONTROL) |
diff --git a/drivers/net/wireless/ath/ath9k/hw.c b/drivers/net/wireless/ath/ath9k/hw.c
index 0ef8566..b51035f 100644
--- a/drivers/net/wireless/ath/ath9k/hw.c
+++ b/drivers/net/wireless/ath/ath9k/hw.c
@@ -1452,6 +1452,7 @@ static bool ath9k_hw_channel_change(struct ath_hw *ah,
ath9k_hw_spur_mitigate_freq(ah, chan);
if (edma && (band_switch || mode_diff)) {
+ ah->ah_flags |= AH_FASTCC;
if (band_switch || ini_reloaded)
ah->eep_ops->set_board_values(ah, chan);
@@ -1459,6 +1460,7 @@ static bool ath9k_hw_channel_change(struct ath_hw *ah,
if (band_switch || ini_reloaded)
ath9k_hw_init_cal(ah, chan);
+ ah->ah_flags &= ~AH_FASTCC;
}
return true;
@@ -1516,6 +1518,7 @@ int ath9k_hw_reset(struct ath_hw *ah, struct ath9k_channel *chan,
u32 macStaId1;
u64 tsf = 0;
int i, r;
+ bool allow_fbs = false;
if (!ath9k_hw_setpower(ah, ATH9K_PM_AWAKE))
return -EIO;
@@ -1537,12 +1540,19 @@ int ath9k_hw_reset(struct ath_hw *ah, struct ath9k_channel *chan,
if (AR_SREV_9280(ah) && common->bus_ops->ath_bus_type == ATH_PCI)
bChannelChange = false;
+ if (caldata &&
+ caldata->done_txiqcal_once &&
+ caldata->done_txclcal_once &&
+ caldata->rtt_hist.num_readings)
+ allow_fbs = true;
+
if (bChannelChange &&
(ah->chip_fullsleep != true) &&
(ah->curchan != NULL) &&
(chan->channel != ah->curchan->channel) &&
- ((chan->channelFlags & CHANNEL_ALL) ==
- (ah->curchan->channelFlags & CHANNEL_ALL))) {
+ (allow_fbs ||
+ ((chan->channelFlags & CHANNEL_ALL) ==
+ (ah->curchan->channelFlags & CHANNEL_ALL)))) {
if (ath9k_hw_channel_change(ah, chan)) {
ath9k_hw_loadnf(ah, ah->curchan);
ath9k_hw_start_nfcal(ah, true);
diff --git a/drivers/net/wireless/ath/ath9k/hw.h b/drivers/net/wireless/ath/ath9k/hw.h
index 64f5a92..3ed3619 100644
--- a/drivers/net/wireless/ath/ath9k/hw.h
+++ b/drivers/net/wireless/ath/ath9k/hw.h
@@ -660,6 +660,7 @@ enum ath_cal_list {
/* ah_flags */
#define AH_USE_EEPROM 0x1
#define AH_UNPLUGGED 0x2 /* The card has been physically removed. */
+#define AH_FASTCC 0x4
struct ath_hw {
struct ath_ops reg_ops;
--
1.7.7
--
To unsubscribe from this list: send the line "unsubscribe linux-wireless" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
