Hi Kalle I used git://github.com/kvalo/ath6kl.git for-linville (Sat Oct 1 09:43:09 2011 +0300) to run AR6003 HW2.0 (hw 2.0 fw 3.1.1.149) in my ARM board. But I faced booting problem as like the following: Is there any changes for AR6003 HW2.0 with the latest ath6kl git ? ----------------------------------------------------------------------- mmc2: queuing unknown CIS tuple 0x01 (3 bytes) mmc2: queuing unknown CIS tuple 0x1a (5 bytes) mmc2: queuing unknown CIS tuple 0x1b (8 bytes) mmc2: queuing unknown CIS tuple 0x14 (0 bytes) mmc2: queuing unknown CIS tuple 0x80 (1 bytes) mmc2: queuing unknown CIS tuple 0x81 (1 bytes) mmc2: queuing unknown CIS tuple 0x82 (1 bytes) mmc2: new high speed SDIO card at address 0001 ath6kl: target_ver 0x30000384 target_type 0x3 dataset_patch 0x57e884 app_load_addr 0x543180 ath6kl: app_start_override_addr 0x0 board_ext_data_addr 0x57e500 reserved_ram_size 0x1b00 ath6kl: using fw api 1 ath6kl: temporary war to avoid sdio crc error ath6kl: writing extended board data to 0x57e500 (768 B) ath6kl: writing board file to 0x541800 (1024 B) ath6kl: writing otp to 0x543180 (3689 B) ath6kl: app_start_override_addr 0x0 ath6kl: executing OTP at 0x0 ath6kl: bmi_recv_buf FIFO empty ath6kl: Unable to read from the device: -22 ath6kl: writing firmware to 0x543180 (100694 B) ath6kl: bmi communication timeout ath6kl: Unable to write to the device: -110 ath6kl: Failed to write firmware: -110 ath6kl: Failed to init ath6kl core ath6kl_sdio: probe of mmc2:0001:1 failed with error -110 -------------------------------------------------------------------------------- Thanks Sangwook On 9 September 2011 09:54, Sangwook Lee <sangwook.lee@xxxxxxxxxx> wrote: > > Hi Kalle > > On 8 September 2011 17:27, Kalle Valo <kvalo@xxxxxxxxxxxxxxxx> wrote: > > Hi Sangwook, > > > > On 09/07/2011 04:32 PM, Sangwook Lee wrote: > >> I am running ath6kl-cleanup git. > > > > BTW, ath6kl-cleanup.git is not updated anymore. Instead there's now > > ath6kl.git which follows wireless-testing. You can find it from > > git.kernel.org (when it's up again) or from github. > > > Thanks for this info, I will use new git. > > >> If I add debug_mask values with ath6kl.ko as like followings, I get > >> the success full results, [snip] > >> $ insmod ath6kl.ko > >> $ ifconfig wlan0 up > >> $ iwlist wlan0 scan > >> With this case, there is no coming event "WMI_SCAN_COMPLETE_EVENTID". > >> After receiving "ath6kl: WMI_EXTENSION_EVENTID" > >> iwlist shows error message: > >> wlan0 Failed to read scan data : Resource temporarily unavailable > > [snip] -- To unsubscribe from this list: send the line "unsubscribe linux-wireless" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
