Search Linux Wireless

[PATCH v2 30/40] wl12xx: AP-mode - configure HT rate support to the FW

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



From: Arik Nemtsov <arik@xxxxxxxxxx>

Unconditionally configure HT rate support to the FW on all ACs
when starting the AP.

When 11n support is disabled by usermode (hostapd), each STA joining
the AP will appear as a non-HT STA. This will stop us from accidentally
transmitting using MCS rates.

Signed-off-by: Arik Nemtsov <arik@xxxxxxxxxx>
Signed-off-by: Eliad Peller <eliad@xxxxxxxxxx>
---
 drivers/net/wireless/wl12xx/conf.h |    5 +++++
 drivers/net/wireless/wl12xx/init.c |    3 +++
 2 files changed, 8 insertions(+), 0 deletions(-)

diff --git a/drivers/net/wireless/wl12xx/conf.h b/drivers/net/wireless/wl12xx/conf.h
index 76b5c62..82f205c 100644
--- a/drivers/net/wireless/wl12xx/conf.h
+++ b/drivers/net/wireless/wl12xx/conf.h
@@ -438,12 +438,17 @@ struct conf_rx_settings {
 
 #define CONF_TX_OFDM_RATES (CONF_HW_BIT_RATE_6MBPS |             \
 	CONF_HW_BIT_RATE_12MBPS | CONF_HW_BIT_RATE_24MBPS |      \
 	CONF_HW_BIT_RATE_36MBPS | CONF_HW_BIT_RATE_48MBPS |      \
 	CONF_HW_BIT_RATE_54MBPS)
 
+#define CONF_TX_MCS_RATES (CONF_HW_BIT_RATE_MCS_0 |              \
+	CONF_HW_BIT_RATE_MCS_1 | CONF_HW_BIT_RATE_MCS_2 |        \
+	CONF_HW_BIT_RATE_MCS_3 | CONF_HW_BIT_RATE_MCS_4 |        \
+	CONF_HW_BIT_RATE_MCS_5 | CONF_HW_BIT_RATE_MCS_6 |        \
+	CONF_HW_BIT_RATE_MCS_7)
 
 /*
  * Default rates for management traffic when operating in AP mode. This
  * should be configured according to the basic rate set of the AP
  */
 #define CONF_TX_AP_DEFAULT_MGMT_RATES  (CONF_HW_BIT_RATE_1MBPS | \
diff --git a/drivers/net/wireless/wl12xx/init.c b/drivers/net/wireless/wl12xx/init.c
index a374c21..b13bebe 100644
--- a/drivers/net/wireless/wl12xx/init.c
+++ b/drivers/net/wireless/wl12xx/init.c
@@ -512,12 +512,15 @@ int wl1271_init_ap_rates(struct wl1271 *wl)
 	 */
 	if ((wl->basic_rate_set & CONF_TX_OFDM_RATES))
 		supported_rates = CONF_TX_OFDM_RATES;
 	else
 		supported_rates = CONF_TX_AP_ENABLED_RATES;
 
+	/* unconditionally enable HT rates */
+	supported_rates |= CONF_TX_MCS_RATES;
+
 	/* configure unicast TX rate classes */
 	for (i = 0; i < wl->conf.tx.ac_conf_count; i++) {
 		rc.enabled_rates = supported_rates;
 		rc.short_retry_limit = 10;
 		rc.long_retry_limit = 10;
 		rc.aflags = 0;
-- 
1.7.6.401.g6a319

--
To unsubscribe from this list: send the line "unsubscribe linux-wireless" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html


[Index of Archives]     [Linux Host AP]     [ATH6KL]     [Linux Bluetooth]     [Linux Netdev]     [Kernel Newbies]     [Linux Kernel]     [IDE]     [Security]     [Git]     [Netfilter]     [Bugtraq]     [Yosemite News]     [MIPS Linux]     [ARM Linux]     [Linux Security]     [Linux RAID]     [Linux ATA RAID]     [Samba]     [Device Mapper]
  Powered by Linux