On Fri, 2011-02-04 at 14:08 +0100, Johannes Berg wrote:
> On Fri, 2011-02-04 at 17:55 +0530, Vivek Natarajan wrote:
> > There is a race on sending a data frame before the tx completion
> > of nullfunc frame for enabling power save. As the data quickly
> > follows the nullfunc frame, the AP thinks that the station is out
> > of power save and continues to send the frames. Whereas in the
> > station, the nullfunc ack will be processed after the tx completion
> > of data frame and mac80211 goes to powersave. Thus the power
> > save state mismatch between the station and the AP causes some
> > data loss and some applications fail because of that. This patch
> > fixes this issue.
> >
> > Signed-off-by: Vivek Natarajan <vnatarajan@xxxxxxxxxxx>
> > ---
> > net/mac80211/ieee80211_i.h | 1 +
> > net/mac80211/mlme.c | 8 ++++++--
> > net/mac80211/tx.c | 8 ++++++++
> > 3 files changed, 15 insertions(+), 2 deletions(-)
> >
> > diff --git a/net/mac80211/ieee80211_i.h b/net/mac80211/ieee80211_i.h
> > index 533fd32..6ad97f6 100644
> > --- a/net/mac80211/ieee80211_i.h
> > +++ b/net/mac80211/ieee80211_i.h
> > @@ -346,6 +346,7 @@ enum ieee80211_sta_flags {
> > IEEE80211_STA_UAPSD_ENABLED = BIT(7),
> > IEEE80211_STA_NULLFUNC_ACKED = BIT(8),
> > IEEE80211_STA_RESET_SIGNAL_AVE = BIT(9),
> > + IEEE80211_STA_PS_PENDING = BIT(10),
> > };
> >
> > struct ieee80211_if_managed {
> > diff --git a/net/mac80211/mlme.c b/net/mac80211/mlme.c
> > index e059b3a..45f736e 100644
> > --- a/net/mac80211/mlme.c
> > +++ b/net/mac80211/mlme.c
> > @@ -727,13 +727,17 @@ void ieee80211_dynamic_ps_enable_work(struct work_struct *work)
> > return;
> >
> > if ((local->hw.flags & IEEE80211_HW_PS_NULLFUNC_STACK) &&
> > - (!(ifmgd->flags & IEEE80211_STA_NULLFUNC_ACKED)))
> > + (!(ifmgd->flags & IEEE80211_STA_NULLFUNC_ACKED))) {
> > + ifmgd->flags |= IEEE80211_STA_PS_PENDING;
> > ieee80211_send_nullfunc(local, sdata, 1);
> > + }
> >
> > if (!((local->hw.flags & IEEE80211_HW_REPORTS_TX_ACK_STATUS) &&
> > (local->hw.flags & IEEE80211_HW_PS_NULLFUNC_STACK)) ||
> > - (ifmgd->flags & IEEE80211_STA_NULLFUNC_ACKED)) {
> > + ((ifmgd->flags & IEEE80211_STA_NULLFUNC_ACKED) &&
> > + ifmgd->flags & IEEE80211_STA_PS_PENDING)) {
> > ifmgd->flags &= ~IEEE80211_STA_NULLFUNC_ACKED;
> > + ifmgd->flags &= ~IEEE80211_STA_PS_PENDING;
> > local->hw.conf.flags |= IEEE80211_CONF_PS;
> > ieee80211_hw_config(local, IEEE80211_CONF_CHANGE_PS);
> > }
> > diff --git a/net/mac80211/tx.c b/net/mac80211/tx.c
> > index 8fbbc7a..e1c2256 100644
> > --- a/net/mac80211/tx.c
> > +++ b/net/mac80211/tx.c
> > @@ -185,6 +185,7 @@ ieee80211_tx_h_dynamic_ps(struct ieee80211_tx_data *tx)
> > {
> > struct ieee80211_local *local = tx->local;
> > struct ieee80211_if_managed *ifmgd;
> > + struct ieee80211_hdr *hdr;
> >
> > /* driver doesn't support power save */
> > if (!(local->hw.flags & IEEE80211_HW_SUPPORTS_PS))
> > @@ -233,6 +234,13 @@ ieee80211_tx_h_dynamic_ps(struct ieee80211_tx_data *tx)
> > && skb_get_queue_mapping(tx->skb) == 0)
> > return TX_CONTINUE;
> >
> > + hdr = (struct ieee80211_hdr *)tx->skb->data;
> > +
> > + if (!(ieee80211_is_nullfunc(hdr->frame_control) &&
> > + ieee80211_has_pm(hdr->frame_control)) &&
> > + (ifmgd->flags & IEEE80211_STA_PS_PENDING))
> > + ifmgd->flags &= ~IEEE80211_STA_PS_PENDING;
> > +
> > if (local->hw.conf.flags & IEEE80211_CONF_PS) {
>
> I don't see how this patch helps anything. Should the last line I quoted
> be replaced instead by checking if PS was requested? We used to not wait
> for the ACK -- so waiting for the ACK broke this.
Ok maybe I see how this helps -- but I don't think it's race-free. When
the PS-pending flag is cleared here, the code above that checks it might
already have passed and be in the driver callback or so.
Maybe the subif queues should be stopped, then flush, then tx nullfunc,
then stop all queues to configure the HW or something like that?
johannes
--
To unsubscribe from this list: send the line "unsubscribe linux-wireless" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
