Fast channel change fixes:
a) Always set OFDM timings
b) Don't re-activate PHY
c) Enable only NF calibration, not AGC
Signed-off-by: Nick Kossifidis <mickflemm@xxxxxxxxx>
---
drivers/net/wireless/ath/ath5k/phy.c | 142 +++++++++++++++++++++-------------
1 files changed, 87 insertions(+), 55 deletions(-)
diff --git a/drivers/net/wireless/ath/ath5k/phy.c b/drivers/net/wireless/ath/ath5k/phy.c
index 78c26fd..d673ab2 100644
--- a/drivers/net/wireless/ath/ath5k/phy.c
+++ b/drivers/net/wireless/ath/ath5k/phy.c
@@ -282,6 +282,34 @@ int ath5k_hw_phy_disable(struct ath5k_hw *ah)
return 0;
}
+/*
+ * Wait for synth to settle
+ */
+static void ath5k_hw_wait_for_synth(struct ath5k_hw *ah,
+ struct ieee80211_channel *channel)
+{
+ /*
+ * On 5211+ read activation -> rx delay
+ * and use it (100ns steps).
+ */
+ if (ah->ah_version != AR5K_AR5210) {
+ u32 delay;
+ delay = ath5k_hw_reg_read(ah, AR5K_PHY_RX_DELAY) &
+ AR5K_PHY_RX_DELAY_M;
+ delay = (channel->hw_value & CHANNEL_CCK) ?
+ ((delay << 2) / 22) : (delay / 10);
+ if (ah->ah_bwmode == AR5K_BWMODE_10MHZ)
+ delay = delay << 1;
+ if (ah->ah_bwmode == AR5K_BWMODE_5MHZ)
+ delay = delay << 2;
+ /* XXX: /2 on turbo ? Let's be safe
+ * for now */
+ udelay(100 + delay);
+ } else {
+ mdelay(1);
+ }
+}
+
/**********************\
* RF Gain optimization *
@@ -3237,6 +3265,13 @@ int ath5k_hw_phy_init(struct ath5k_hw *ah, struct ieee80211_channel *channel,
/* Failed */
if (i >= 100)
return -EIO;
+
+ /* Set channel and wait for synth */
+ ret = ath5k_hw_channel(ah, channel);
+ if (ret)
+ return ret;
+
+ ath5k_hw_wait_for_synth(ah, channel);
}
/*
@@ -3251,13 +3286,53 @@ int ath5k_hw_phy_init(struct ath5k_hw *ah, struct ieee80211_channel *channel,
if (ret)
return ret;
+ /* Write OFDM timings on 5212*/
+ if (ah->ah_version == AR5K_AR5212 &&
+ channel->hw_value & CHANNEL_OFDM) {
+
+ ret = ath5k_hw_write_ofdm_timings(ah, channel);
+ if (ret)
+ return ret;
+
+ /* Spur info is available only from EEPROM versions
+ * greater than 5.3, but the EEPROM routines will use
+ * static values for older versions */
+ if (ah->ah_mac_srev >= AR5K_SREV_AR5424)
+ ath5k_hw_set_spur_mitigation_filter(ah,
+ channel);
+ }
+
+ /* If we used fast channel switching
+ * we are done, release RF bus and
+ * fire up NF calibration.
+ *
+ * Note: Only NF calibration due to
+ * channel change, not AGC calibration
+ * since AGC is still running !
+ */
+ if (fast) {
+ /*
+ * Release RF Bus grant
+ */
+ AR5K_REG_DISABLE_BITS(ah, AR5K_PHY_RFBUS_REQ,
+ AR5K_PHY_RFBUS_REQ_REQUEST);
+
+ /*
+ * Start NF calibration
+ */
+ AR5K_REG_ENABLE_BITS(ah, AR5K_PHY_AGCCTL,
+ AR5K_PHY_AGCCTL_NF);
+
+ return ret;
+ }
+
/*
* For 5210 we do all initialization using
* initvals, so we don't have to modify
* any settings (5210 also only supports
* a/aturbo modes)
*/
- if ((ah->ah_version != AR5K_AR5210) && !fast) {
+ if (ah->ah_version != AR5K_AR5210) {
/*
* Write initial RF gain settings
@@ -3276,22 +3351,6 @@ int ath5k_hw_phy_init(struct ath5k_hw *ah, struct ieee80211_channel *channel,
if (ret)
return ret;
- /* Write OFDM timings on 5212*/
- if (ah->ah_version == AR5K_AR5212 &&
- channel->hw_value & CHANNEL_OFDM) {
-
- ret = ath5k_hw_write_ofdm_timings(ah, channel);
- if (ret)
- return ret;
-
- /* Spur info is available only from EEPROM versions
- * greater than 5.3, but the EEPROM routines will use
- * static values for older versions */
- if (ah->ah_mac_srev >= AR5K_SREV_AR5424)
- ath5k_hw_set_spur_mitigation_filter(ah,
- channel);
- }
-
/*Enable/disable 802.11b mode on 5111
(enable 2111 frequency converter + CCK)*/
if (ah->ah_radio == AR5K_RF5111) {
@@ -3322,47 +3381,20 @@ int ath5k_hw_phy_init(struct ath5k_hw *ah, struct ieee80211_channel *channel,
*/
ath5k_hw_reg_write(ah, AR5K_PHY_ACT_ENABLE, AR5K_PHY_ACT);
+ ath5k_hw_wait_for_synth(ah, channel);
+
/*
- * On 5211+ read activation -> rx delay
- * and use it.
+ * Perform ADC test to see if baseband is ready
+ * Set tx hold and check adc test register
*/
- if (ah->ah_version != AR5K_AR5210) {
- u32 delay;
- delay = ath5k_hw_reg_read(ah, AR5K_PHY_RX_DELAY) &
- AR5K_PHY_RX_DELAY_M;
- delay = (channel->hw_value & CHANNEL_CCK) ?
- ((delay << 2) / 22) : (delay / 10);
- if (ah->ah_bwmode == AR5K_BWMODE_10MHZ)
- delay = delay << 1;
- if (ah->ah_bwmode == AR5K_BWMODE_5MHZ)
- delay = delay << 2;
- /* XXX: /2 on turbo ? Let's be safe
- * for now */
- udelay(100 + delay);
- } else {
- mdelay(1);
- }
-
- if (fast)
- /*
- * Release RF Bus grant
- */
- AR5K_REG_DISABLE_BITS(ah, AR5K_PHY_RFBUS_REQ,
- AR5K_PHY_RFBUS_REQ_REQUEST);
- else {
- /*
- * Perform ADC test to see if baseband is ready
- * Set tx hold and check adc test register
- */
- phy_tst1 = ath5k_hw_reg_read(ah, AR5K_PHY_TST1);
- ath5k_hw_reg_write(ah, AR5K_PHY_TST1_TXHOLD, AR5K_PHY_TST1);
- for (i = 0; i <= 20; i++) {
- if (!(ath5k_hw_reg_read(ah, AR5K_PHY_ADC_TEST) & 0x10))
- break;
- udelay(200);
- }
- ath5k_hw_reg_write(ah, phy_tst1, AR5K_PHY_TST1);
+ phy_tst1 = ath5k_hw_reg_read(ah, AR5K_PHY_TST1);
+ ath5k_hw_reg_write(ah, AR5K_PHY_TST1_TXHOLD, AR5K_PHY_TST1);
+ for (i = 0; i <= 20; i++) {
+ if (!(ath5k_hw_reg_read(ah, AR5K_PHY_ADC_TEST) & 0x10))
+ break;
+ udelay(200);
}
+ ath5k_hw_reg_write(ah, phy_tst1, AR5K_PHY_TST1);
/*
* Start automatic gain control calibration
--
To unsubscribe from this list: send the line "unsubscribe linux-wireless" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
